FordParts
My Garage
My Account
Cart
OEM 2000 Lincoln Town Car ABS Control Module
Anti Lock Brake Control Module- Select Vehicle by Model
- Select Vehicle by VIN
Select Vehicle by Model
orMake
Model
Year
Select Vehicle by VIN
For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).
3 ABS Control Modules found
2000 Lincoln Town Car ABS Pump Assembly
Part Number: 1W1Z-2C286-DAProduct Specifications- Other Name: Control; ABS Pump And Motor Assembly
- Manufacturer Note: Complete unit with bracket, ABS & TC Less Special purpose vehicle
- Base No.: 2C286
- Item Weight: 5.40 Pounds
- Item Dimensions: 2.6 x 6.4 x 7.5 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 1W1Z-2C286-DA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
2000 Lincoln Town Car Control Module
Part Number: XW7Z-2C219-AAProduct Specifications- Other Name: Control; ABS Control Module
- Manufacturer Note: w/ Traction assist
- Base No.: 2C219
- Item Weight: 1.70 Pounds
- Item Dimensions: 2.7 x 6.4 x 7.6 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: XW7Z-2C219-AA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
2000 Lincoln Town Car Control Module
Part Number: F8VZ-2C219-BAProduct Specifications- Other Name: Control; ABS Control Module
- Manufacturer Note: ECU only, w/o Traction assist
- Base No.: 2C219
- Item Weight: 1.80 Pounds
- Item Dimensions: 2.6 x 6.4 x 7.4 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: F8VZ-2C219-BA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
2000 Lincoln Town Car ABS Control Module
If you're seeking quality and affordability, look no further than our extensive inventory of genuine 2000 Lincoln Town Car ABS Control Module available at FordPartsDeal.com. You can confidently purchase our OEM 2000 Lincoln Town Car ABS Control Module as they are supported by the manufacturer's warranty and our hassle-free return policy, alongside the benefit of our fast delivery service.
2000 Lincoln Town Car ABS Control Module Parts Questions & Experts Answers
- Q: How to Bleed the Brake System After Installing a New ABS Control Module on 2000 Lincoln Town Car?A: The first step to bleed the brake system after installing a new four-wheel anti-lock brake (4WABS) hydraulic control unit (HCU) or opening the HCU lines starts by cleaning the area around the brake master cylinder filler cap followed by removing the cap to fill the reservoir with approved DOT 3 brake fluid while avoiding dry-out of the master cylinder during the procedure. Connect a clear waste line to the right-hand (RH) rear bleeder screw while directing the other end to a container filled with recommended brake fluid to a certain extent. Allow the RH rear bleeder screw to loosen as fluid starts flowing which allows an assistant to apply brake pedal pressure for screw tightening. Continuously perform this task until only clear fluid flows out of the bleeder screws while(regularly) replenishing the master cylinder reservoir with new brake fluid. The process continues with tightening the RH rear bleeder screw and waste line disconnection followed by LH rear bleeder screw and an order of RH then LH front disc brake caliper bleeder screws. The scan tool DCL cable adapter needs connection to the vehicle data link connector (DLC) under the dash before following scan tool instructions for a second bleeding procedure execution.
Related 2000 Lincoln Town Car Parts
2000 Lincoln Town Car Brake Pads
2000 Lincoln Town Car ABS Pump And Motor Assembly
2000 Lincoln Town Car ABS Reluctor Ring
2000 Lincoln Town Car ABS Sensor
2000 Lincoln Town Car Brake Controller
2000 Lincoln Town Car Brake Disc
2000 Lincoln Town Car Brake Line
2000 Lincoln Town Car Brake Shoe
2000 Lincoln Town Car Hydraulic Hose
2000 Lincoln Town Car Parking Brake Shoe
2000 Lincoln Town Car Wheel Bearing Dust Cap
2000 Lincoln Town Car Wheel Hub