FordParts
My Garage
My Account
Cart
OEM 2003 Ford Mustang Brake Pads
Disc Brake Pad Set- Select Vehicle by Model
- Select Vehicle by VIN
Select Vehicle by Model
orMake
Model
Year
Select Vehicle by VIN
For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).
4 Brake Pads found
2003 Ford Mustang Brake Pads, Front Part Number: YU2Z-2V001-DA
$45.79 MSRP: $66.65You Save: $20.86 (32%)Product Specifications- Other Name: Pad; Disc Brake Pad Set, Front; Front Pads; Disc Brake Pad Set
- Position: Front
- Replaces: XR3Z-2001-AA, BRF-1491
- Base No.: 2001
- Item Weight: 4.60 Pounds
- Item Dimensions: 2.5 x 5.3 x 8.8 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: YU2Z-2V001-DA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
2003 Ford Mustang Brake Pads, Rear Part Number: 1U2Z-2V200-FA
$50.07 MSRP: $74.98You Save: $24.91 (34%)Product Specifications- Other Name: Kit - Brake Shoe And Lining; Disc Brake Pad Set, Rear; Rear Pads; Disc Brake Pad Set
- Manufacturer Note: Ford Retail Spec
- Position: Rear
- Replaces: F5ZZ-2200-A, F4ZZ-2200-A, XU2Z-2V200-MA, BRF-1489
- Base No.: 2200
- Item Weight: 2.10 Pounds
- Item Dimensions: 2.7 x 4.5 x 5.4 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 1U2Z-2V200-FA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Product Specifications- Other Name: Kit - Brake Shoe And Hardware; Disc Brake Caliper, Rear Left; Disc Brake Pad Set, Rear; Disc Brake Pad Kit; Rear Pads; Kit - Brake Shoe And Lining; Disc Brake Pad Set
- Manufacturer Note: Warranty Eligible
- Position: Rear Driver Side
- Base No.: 2200
- Item Weight: 2.10 Pounds
- Item Dimensions: 6.7 x 4.1 x 3.3 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 3R3Z-2200-AA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
2003 Ford Mustang Brake Pads, Front Part Number: F5ZZ-2001-A
Product Specifications- Other Name: Kit - Brake Shoe; Disc Brake Pad Set, Front; Disc Brake Pad Kit; Front Pads; Disc Brake Pad Set
- Position: Front
- Base No.: 2001
- Item Weight: 4.40 Pounds
- Item Dimensions: 4.3 x 5.1 x 6.0 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: F5ZZ-2001-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
2003 Ford Mustang Brake Pads
If you're seeking quality and affordability, look no further than our extensive inventory of genuine 2003 Ford Mustang Brake Pads available at FordPartsDeal.com. You can confidently purchase our OEM 2003 Ford Mustang Brake Pads as they are supported by the manufacturer's warranty and our hassle-free return policy, alongside the benefit of our fast delivery service.
2003 Ford Mustang Brake Pads Parts Q&A
- Q: How to service and repair the front brake pads on 2003 Ford Mustang?A: You should start pad and brake repair by opening the master cylinder filler cap and checking reservoir fluid before draining some fluid when it reaches half its capacity. Beginning service on the front brake pads requires wheel and tire removal after raising and supporting the vehicle. Brake pad replacement needs new pads because they reach the specified metal backing plate or rivet thickness points and pad installation should occur as complete axle units. Check the pads for indications of wear together with any presence of contamination. Proceed to detach the caliper bolts but maintain the guide pins in their current position before discarding the bolts altogether. The caliper sight hole should be avoided for piston retraction because probing will cause damage to the components; supporting the caliper will keep it from hanging by the brake hose. You should shift the caliper off the anchor plate before taking out the pads together with pad slippers. After pad removal complete a pad thickness verification and eliminate the slippers. The disc measurement should be checked for specification. If outside range, get a new replacement disc. The disc brake caliper needs examination for leaks alongside boot integrity because these issues will require tear-down but the front disc brake anchor plate requires inspection for worn guide pin boots or binding guide pins or damaged pins that need replacement. The installation process requires pad lining material to remain free from grease, oil and brake fluid or other contaminants and exclusive use of uncorrupted pads. Start pad installation by fitting all hardware kit contents that begin with the new pad slippers followed by the pads. A wood block or used pad can safeguard pistons and boots during compression of caliper pistons. The installation of the disc brake caliper requires the anti-rattle spring to be positioned correctly within the caliper before securing the guide pins while caliper bolt installation occurs. Install the wheel assembly and lower the vehicle before filling the master cylinder reservoir with clean brake fluid C6AZ-19542-AB or an equivalent DOT 3 fluid Ford specifies as ESA-M6C25-A. Follow the procedure by replacing the filler cap afterward. Finally, inspect the brake operation.
Related 2003 Ford Mustang Parts
2003 Ford Mustang ABS Sensor
2003 Ford Mustang Wheel Bearing
2003 Ford Mustang Wheel Hub
2003 Ford Mustang Brake Caliper
2003 Ford Mustang ABS Reluctor Ring
2003 Ford Mustang Brake Backing Plate
2003 Ford Mustang Brake Caliper Piston
2003 Ford Mustang Brake Line
2003 Ford Mustang Hydraulic Hose
2003 Ford Mustang Spindle Nut
2003 Ford Mustang Wheel Bearing Dust Cap
2003 Ford Mustang Wheel Cylinder Repair Kit