FordParts
My Garage
My Account
Cart
OEM 2005 Mercury Monterey Brake Pads
Disc Brake Pad Set- Select Vehicle by Model
- Select Vehicle by VIN
Select Vehicle by Model
orMake
Model
Year
Select Vehicle by VIN
For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).
2 Brake Pads found
2005 Mercury Monterey Brake Pads Part Number: 6F2Z-2001-S
$45.93 MSRP: $62.50You Save: $16.57 (27%)Product Specifications- Other Name: Kit - Brake Shoe; Disc Brake Pad Set; Front Pads
- Manufacturer Note: Warranty Eligible
- Base No.: 2001
- Item Weight: 5.00 Pounds
- Item Dimensions: 0.7 x 2.8 x 7.2 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 6F2Z-2001-S
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
2005 Mercury Monterey Brake Pads Part Number: 5F2Z-2200-AA
$40.96 MSRP: $55.74You Save: $14.78 (27%)Product Specifications- Other Name: Kit - Brake Shoe And Lining; Disc Brake Pad Set; Rear Pads
- Manufacturer Note: Warranty Eligible
- Replaces: 3F2Z-2200-AA
- Base No.: 2200
- Item Weight: 3.30 Pounds
- Item Dimensions: 6.6 x 4.5 x 3.0 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 5F2Z-2200-AA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
2005 Mercury Monterey Brake Pads
If you're seeking quality and affordability, look no further than our extensive inventory of genuine 2005 Mercury Monterey Brake Pads available at FordPartsDeal.com. You can confidently purchase our OEM 2005 Mercury Monterey Brake Pads as they are supported by the manufacturer's warranty and our hassle-free return policy, alongside the benefit of our fast delivery service.
2005 Mercury Monterey Brake Pads Parts Q&A
- Q: How to service and repair the front brake pads on 2005 Mercury Monterey?A: Start service and repair of front brake pads with DOT 3 brake fluid made for motor vehicles since alternative types will damage brake elements permanently and disable the brakes which creates hazards for personal safety. Handle brake fluid with extreme caution to avoid eye contact so wash your hands thoroughly after use but handle contact by flushing eyes with running water for 15 minutes along with seeking medical help for continuing irritation. Swallowing brake fluid requires you to drink water followed by vomiting which must be accompanied by urgent medical aid. Brake fluid poses a danger to painted and plastic materials so you must rinse away all leaks immediately with water. The brake master cylinder reservoir requires checking for fluid level and you should drain the fluid down to half capacity when needed. Position the vehicle with neutral gear into a hoist. Support the disc brake caliper when removing it from the flexible hose during your work. Separate the brake caliper through removing its two bolts before positioning it aside. It is important to replace brake pads when they wear past the metal backing plate threshold yet maintain serviceable position while only changing brake pads in pairs for the complete axle system. Brake pads with the attached four spring clips should be removed while discarding all spring clips. Proper inspection of guide and locator pin boots should be followed by necessary replacement or pin lubrication application. The new spring clips should be installed with their tabs facing away from the brake disc. A proper tool should compress the disc brake caliper pistons into the caliper piston bore through protection of both pistons and boots without forcing them in the sight hole to reduce any potential damage. Begin installation of the brake caliper by tightening the bottom locator pin caliper bolt until you move to securing the top guide pin caliper bolt. Position the caliper into its final location before installing and torquing its two bolts to 35 Nm (26 ft. lbs.). Check brake fluid reservoir with clean brake fluid then perform a brake operation test to assure normal functions.