How to Service and Repair the Front Blend Door Actuator for the Floor Defrost Door on 2007 Ford Crown Victoria?

Start the vacuum control motor floor defrost door servicing and repair process by taking out the left-hand lower instrument panel insulator then removing both pin-type retainers followed by removing the trim panel. Remove first the two screws which secure the data link connector while detaching simultaneously the vacuum line. Begin by taking out the lighting control module through unscrewing screws which allows disengaging the clip before disconnecting electrical connectors. The second step involves taking off the screws along with the lighting control module bracket. Reach the floor/defrost door vacuum control motor by removing first its clip and then the two nuts holding it before removing the motor. Detach the vacuum connectors from the floor/defrost door vacuum control motor as the final step. The installation process ends with inverse execution of removal tasks.

OEM 2007 Ford Crown Victoria Blend Door Actuator

Air Blend Door Actuator

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

2 Blend Door Actuators found

View related parts
2007 Ford Crown Victoria Door Actuator Part Number: AW7Z-19E616-A
$50.15 MSRP: $80.91
You Save: $30.76 (39%)
ADD TO CART
Product Specifications
- Other Name: Motor Assembly; HVAC Air Inlet Door Actuator; HVAC Heater Blend Door Actuator; Actuator Assembly
- Replaces: 1W7Z-19E616-AA, XW7Z-19E616-AA
- Base No.: 19E616
- Item Weight: 0.60 Pounds
- Item Dimensions: 8.5 x 7.7 x 7.9 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: AW7Z-19E616-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2007 Ford Crown Victoria Submodels:
- Base, LWB, LX, LX Sport, Police Interceptor, S, Special Edition | 8 Cyl 4.6 L CNG, 8 Cyl 4.6 L FLEX, 8 Cyl 4.6 L GAS
View related parts
2007 Ford Crown Victoria Door Actuator Part Number: XW7Z-19E616-BA
$47.22 MSRP: $76.18
You Save: $28.96 (39%)
ADD TO CART
Product Specifications
- Other Name: Motor Assembly; HVAC Air Inlet Door Actuator; HVAC Heater Blend Door Actuator; HVAC Blend Door Actuator; Actuator Assembly
- Replaces: F8VZ-19E616-BA
- Base No.: 19E616
- Item Weight: 0.60 Pounds
- Item Dimensions: 8.4 x 7.7 x 7.9 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: XW7Z-19E616-BA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2007 Ford Crown Victoria Submodels:
- Base, LWB, LX, LX Sport, Police Interceptor, S, Special Edition, Touring Sedan | 8 Cyl 4.6 L CNG, 8 Cyl 4.6 L FLEX, 8 Cyl 4.6 L GAS

2007 Ford Crown Victoria Blend Door Actuator

If you're seeking quality and affordability, look no further than our extensive inventory of genuine 2007 Ford Crown Victoria Blend Door Actuator available at FordPartsDeal.com. You can confidently purchase our OEM 2007 Ford Crown Victoria Blend Door Actuator as they are supported by the manufacturer's warranty and our hassle-free return policy, alongside the benefit of our fast delivery service.

2007 Ford Crown Victoria Blend Door Actuator Parts Q&A

Q: How to Service and Repair the Front Blend Door Actuator for the Floor Defrost Door on 2007 Ford Crown Victoria?
A: Start the vacuum control motor floor defrost door servicing and repair process by taking out the left-hand lower instrument panel insulator then removing both pin-type retainers followed by removing the trim panel. Remove first the two screws which secure the data link connector while detaching simultaneously the vacuum line. Begin by taking out the lighting control module through unscrewing screws which allows disengaging the clip before disconnecting electrical connectors. The second step involves taking off the screws along with the lighting control module bracket. Reach the floor/defrost door vacuum control motor by removing first its clip and then the two nuts holding it before removing the motor. Detach the vacuum connectors from the floor/defrost door vacuum control motor as the final step. The installation process ends with inverse execution of removal tasks.