How to Service and Repair the ABS Control Module on Ford Explorer?

Service and repair work on Electronic Brake Control Module requires beginning by disconnecting the battery ground cable. The first steps for pre-March 2002 vehicles include disconnecting electrical connectors then removing three bolts before using a hoist to position the vehicle in neutral and finally removing lower bracket three nuts to safely set aside the anti-lock control module and hydraulic control unit. Remove the screws which fasten the anti-lock brake control module for vehicles built after March 2002 to remove the module. The new module installation demands that the user must keep in mind a potential requirement to enter module configuration details. The vehicle will go through an adaptive learning process after reconnecting the battery because of which it may produce irregular drive symptoms requiring at least 16 km (10 mi) of driving to relearn the adaptive strategy. The installation should be finished by following the opposite order of the removal steps.

How to Properly Bleed the ABS Control Module on Ford Explorer?

Brake fluid used to bleed the ABS Hydraulic Control Unit (HCU) should be new material that meets manufacturer specs without containing previously drained fluid because contamination will cause system damage. The braking system requires an adequate amount of brake fluid in the master cylinder throughout the bleeding operation for proper maintenance and to protect its components from damage. Wash away spilled brake fluid immediately with water because it harms painted and plastic surfaces. The bleeding process serves a specific purpose to remove air from the system which naturally enters following disconnected HCU installations or any part of the hydraulic system's disconnection. Bleeding of the hydraulic system works both by hand and through pressure bleeding tools. The first step requires tool connection to the vehicle for accessing ABS HCU bleed function after verifying that HCU module receives sufficient voltage during anti-lock control. First complete the scan tool instructions after that perform manual brake hydraulic system bleeding. The total system requires two scan tool cycles and two manual bleed cycles in order to eliminate all trapped air from the system.

OEM Ford Explorer ABS Control Module

Anti Lock Brake Control Module

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

34 ABS Control Modules found

View related parts
Ford Explorer Control Module Part Number: EB5Z-2C219-B
$409.33 MSRP: $468.77
You Save: $59.44 (13%)
ADD TO CART
Product Specifications
- Other Name: Control; ABS Control Module; Module
- Replaces: EB5Z-2C219-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2014-2015 Ford Explorer | Base, Limited, Sport, XLT | 4 Cyl 2.0 L GAS, 6 Cyl 3.5 L GAS
View related parts
Ford Explorer Modulator Valve Part Number: DB5Z-2C405-E
$800.60 MSRP: $1006.67
You Save: $206.07 (21%)
ADD TO CART
Product Specifications
- Other Name: Unit Assembly - Control; ABS Hydraulic Assembly; ABS Control Module; Control Assembly
- Replaces: DB5Z-2C405-A, CB5Z-2C405-C, DB5Z-2C405-C
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2011-2014 Ford Explorer | Base, Limited, Sport, XLT | 4 Cyl 2.0 L GAS, 6 Cyl 3.5 L GAS
View related parts
Ford Explorer Control Module Part Number: 4L2Z-2B373-BD
Product Specifications
- Other Name: Control; ABS Control Module
- Manufacturer Note: ECU
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2004-2005 Ford Explorer | Eddie Bauer, Limited, NBX, XLS, XLS Sport, XLT, XLT Sport | 6 Cyl 4.0 L FLEX, 6 Cyl 4.0 L GAS, 8 Cyl 4.6 L GAS
View related parts
Ford Explorer Control Module Part Number: 7A2Z-2C219-E
Product Specifications
- Other Name: Control; ABS Control Module; ABS Control Unit
- Replaces: 7A2Z-2C219-D
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2006-2008 Ford Explorer | Eddie Bauer, Limited, XLS, XLT | 6 Cyl 4.0 L GAS, 8 Cyl 4.6 L GAS
View related parts
Ford Explorer Control Module Part Number: 1L5Z-2B373-BC
Product Specifications
- Other Name: Control; ABS Hydraulic Assembly; ABS Control Module; ABS Control Unit
- Manufacturer Note: ECU only
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2001 Ford Explorer | Eddie Bauer, Limited, Postal, XL Fleet, XLS, XLT | 6 Cyl 4.0 L GAS, 8 Cyl 5.0 L GAS
View related parts
Ford Explorer Control Module Part Number: 1L5Z-2B373-AC
Product Specifications
- Other Name: Control; ABS Hydraulic Assembly; ABS Control Module; ABS Control Unit
- Manufacturer Note: ECU only
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2001 Ford Explorer | Eddie Bauer, Limited, Postal, XL Fleet, XLS, XLT | 6 Cyl 4.0 L GAS, 8 Cyl 5.0 L GAS
View related parts
Ford Explorer Modulator Valve Part Number: 2C5Z-2C215-AA
Product Specifications
- Other Name: Module; ABS Control Module; ABS Control Unit
- Manufacturer Note: HCU
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2002-2003 Ford Explorer | Eddie Bauer, Limited, XLS, XLT | 6 Cyl 4.0 L FLEX, 6 Cyl 4.0 L GAS, 8 Cyl 4.6 L GAS
View related parts
Ford Explorer Control Module Part Number: 2L2Z-2B373-AA
Product Specifications
- Other Name: Control; ABS Control Module
- Manufacturer Note: ECU
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2002-2003 Ford Explorer | Eddie Bauer, Limited, XLS, XLT | 6 Cyl 4.0 L FLEX, 6 Cyl 4.0 L GAS, 8 Cyl 4.6 L GAS
View related parts
Ford Explorer Modulator Valve Part Number: 2L2Z-2C215-AA
Product Specifications
- Other Name: Module; ABS Hydraulic Assembly; ABS Control Module; ABS Control Unit
- Manufacturer Note: HCU
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2002-2003 Ford Explorer | Eddie Bauer, Limited, XLS, XLT | 6 Cyl 4.0 L FLEX, 6 Cyl 4.0 L GAS, 8 Cyl 4.6 L GAS
View related parts
Ford Explorer Control Module Part Number: 3L2Z-2B373-DA
Product Specifications
- Other Name: Control; ABS Control Module; ABS Control Unit
- Manufacturer Note: ECU
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2002-2003 Ford Explorer | Eddie Bauer, Limited, XLS, XLT | 6 Cyl 4.0 L FLEX, 6 Cyl 4.0 L GAS, 8 Cyl 4.6 L GAS
View related parts
Ford Explorer Control Module Part Number: 4L1Z-2B373-AA
Product Specifications
- Other Name: Control; ABS Hydraulic Assembly; ABS Control Module; ABS Control Unit
- Replaces: 2L1Z-2B373-AB
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2002-2003 Ford Explorer | Eddie Bauer, Limited, XLS, XLT | 6 Cyl 4.0 L FLEX, 6 Cyl 4.0 L GAS, 8 Cyl 4.6 L GAS
View related parts
Ford Explorer Control Module Part Number: 4L2Z-2B373-AD
Product Specifications
- Other Name: Control; ABS Control Module
- Manufacturer Note: ECU
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2004-2005 Ford Explorer | Eddie Bauer, Limited, NBX, XLS, XLS Sport, XLT, XLT Sport | 6 Cyl 4.0 L FLEX, 6 Cyl 4.0 L GAS, 8 Cyl 4.6 L GAS
View related parts
Ford Explorer Control Module Part Number: 4L2Z-2B373-CB
Product Specifications
- Other Name: Control; ABS Control Module
- Manufacturer Note: ECU
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2004-2005 Ford Explorer | Eddie Bauer, Limited, NBX, XLS, XLS Sport, XLT, XLT Sport | 6 Cyl 4.0 L FLEX, 6 Cyl 4.0 L GAS, 8 Cyl 4.6 L GAS
View related parts
Ford Explorer Modulator Valve Part Number: 4L2Z-2C215-AA
Product Specifications
- Other Name: Module; ABS Hydraulic Assembly; ABS Control Module; ABS Control Unit
- Manufacturer Note: HCU
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2004-2005 Ford Explorer | Eddie Bauer, Limited, NBX, XLS, XLS Sport, XLT, XLT Sport | 6 Cyl 4.0 L FLEX, 6 Cyl 4.0 L GAS, 8 Cyl 4.6 L GAS
View related parts
Ford Explorer Modulator Valve Part Number: 4L2Z-2C215-BA
Product Specifications
- Other Name: Module; ABS Hydraulic Assembly; ABS Control Module; ABS Control Unit
- Manufacturer Note: HCU
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2004-2005 Ford Explorer | Eddie Bauer, Limited, NBX, XLS, XLS Sport, XLT, XLT Sport | 6 Cyl 4.0 L FLEX, 6 Cyl 4.0 L GAS, 8 Cyl 4.6 L GAS
View related parts
Ford Explorer Control Module Part Number: 5L2Z-2C219-A
Product Specifications
- Other Name: Control; ABS Control Module
- Replaces: 5L2Z-2C219-DA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2005 Ford Explorer | Eddie Bauer, Limited, XLS, XLS Sport, XLT, XLT Sport | 6 Cyl 4.0 L FLEX, 6 Cyl 4.0 L GAS, 8 Cyl 4.6 L GAS
View related parts
Ford Explorer Control Module Part Number: F57Z-2C219-A
Product Specifications
- Other Name: Module & Bracket Assembly; ABS Control Module; Module & Brkt Assembly-Power Steering
- Manufacturer Note: ECU, 4 wheel ABS
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1995-1997 Ford Explorer | Eddie Bauer, Expedition, Limited, Sport, XL, XLT | 6 Cyl 4.0 L GAS, 8 Cyl 5.0 L GAS
View related parts
Ford Explorer ABS Control Unit Part Number: F5TZ2C215B
Product Specifications
- Other Name: Module; ABS Hydraulic Assembly; ABS Control Module; Hydraulic Unit
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1995-1997 Ford Explorer | Eddie Bauer, Expedition, Limited, Sport, XL, XLT | 6 Cyl 4.0 L GAS, 8 Cyl 5.0 L GAS
View related parts
Ford Explorer Pressure Valve Part Number: F87Z-2B373-AE
Product Specifications
- Other Name: Valve Assembly - Modulator; Brake Proportioning Valve; Modulator Valve; Valve Assembly; Proportioner Valve
- Replaces: F87Z-2B373-ARM
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1991-2001 Ford Explorer | Eddie Bauer, Expedition, Limited, Postal, Sport, XL, XL Fleet, XLS, XLT | 6 Cyl 4.0 L GAS, 8 Cyl 5.0 L GAS
View related parts
Ford Explorer ABS Control Unit Part Number: XL2Z-2C215-AA
Product Specifications
- Other Name: Module; ABS Hydraulic Assembly; ABS Control Module; Hydraulic Unit
- Manufacturer Note: Hydraulic control unit only
- Replaces: F87Z-2C215-AA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1998-2001 Ford Explorer | Eddie Bauer, Limited, Postal, Sport, XL, XL Fleet, XLS, XLT | 6 Cyl 4.0 L GAS, 8 Cyl 5.0 L GAS

| Page 1 of 2 |Next >

1-20 of 34 Results

Ford Explorer ABS Control Module

OEM ABS Control Module boasts unmatched quality. Each part goes through full quality checks. They adhere to Ford's official factory standards. These steps remove flaws and inconsistencies. So you can get ABS Control Module with long life and a perfect fit. Come to our website and find genuine Ford Explorer parts. We keep a wide inventory of OEM Explorer parts at the highly affordable prices. It's easy to search, compare, and pick what you need. You'll love the clear info and simple checkout. We offer top-rated customer service, and we reply fast. We also ship promptly to ensure your order arrives on time.

The function of the Ford Explorer ABS Control Module is critical to the proper functioning of the Ford Explorer's anti-lock brake system in avoiding lockups throughout the brake operation. With regard to critical features of a car, the ABS Control Module ensures that wheel lock-age occurs and this is essential because it increases the level of control when braking and thus, minimizes possible skidding of the car. Proceeding with the advanced module, this system works in conjunction with the wheel speed sensors, valves, a pump along with an ECU; these components are responsible for maintaining wheel speed and adjusting the pressure of the brake. The Ford Explorer has been in production since 1991 and has undergone many changes in the type of ABS Control Module used; most contemporary vehicles main a computerized type that is combined with an ESC system for stability during aggressive control conditions. Where models of different generations of the Explorer are compatible, drivers receive improvements in braking and safety. The key to why the Ford Explorer ABS Control Module is unique in the automotive market is partly because of its complex casting and the additional sensors which make the control of vehicle direction correction during skids even finer. Being the highly popular and sought-after model of America's automobiles, the Ford Explorer still undergoes upgrade and changes; thus, the ABS Control Module does not only signify Ford's dedication to power and protection, yet it is a must-have addition for every one owning an Explorer vehicle due to its reliability and assurance for every driver on the highway.

Ford Explorer ABS Control Module Parts and Q&A

Control Module
1L2Z-2C219-AA
Q: How to Service and Repair the ABS Control Module on Ford Explorer?
A:
Service and repair work on Electronic Brake Control Module requires beginning by disconnecting the battery ground cable. The first steps for pre-March 2002 vehicles include disconnecting electrical connectors then removing three bolts before using a hoist to position the vehicle in neutral and finally removing lower bracket three nuts to safely set aside the anti-lock control module and hydraulic control unit. Remove the screws which fasten the anti-lock brake control module for vehicles built after March 2002 to remove the module. The new module installation demands that the user must keep in mind a potential requirement to enter module configuration details. The vehicle will go through an adaptive learning process after reconnecting the battery because of which it may produce irregular drive symptoms requiring at least 16 km (10 mi) of driving to relearn the adaptive strategy. The installation should be finished by following the opposite order of the removal steps.
Control Module
7L2Z-2C215-A
Q: How to Properly Bleed the ABS Control Module on Ford Explorer?
A:
Brake fluid used to bleed the ABS Hydraulic Control Unit (HCU) should be new material that meets manufacturer specs without containing previously drained fluid because contamination will cause system damage. The braking system requires an adequate amount of brake fluid in the master cylinder throughout the bleeding operation for proper maintenance and to protect its components from damage. Wash away spilled brake fluid immediately with water because it harms painted and plastic surfaces. The bleeding process serves a specific purpose to remove air from the system which naturally enters following disconnected HCU installations or any part of the hydraulic system's disconnection. Bleeding of the hydraulic system works both by hand and through pressure bleeding tools. The first step requires tool connection to the vehicle for accessing ABS HCU bleed function after verifying that HCU module receives sufficient voltage during anti-lock control. First complete the scan tool instructions after that perform manual brake hydraulic system bleeding. The total system requires two scan tool cycles and two manual bleed cycles in order to eliminate all trapped air from the system.