What Are the Differences in Tail Pipe and Muffler Assembly Construction Between the Production and Service Version for PZEV and Non-PZEV on Ford Focus?

The production muffler and tailpipe assembly is built into one piece but the service version contains three pieces for Partial Zero Emissions Vehicles (PZEV) and two pieces for non-PZEV. The installation of service sections requires the production exhaust system to be cut at an accurate position before moving forward. Position the vehicle at neutral mode on a hoist. A support wrap or splint must be added around the exhaust flexible pipe to stop bending or twisting that would harm the pipe. The PZEV removal procedure includes taking out the two exhaust flexible pipe nuts which must be discarded alongside the gasket. The removal process for non-PZEV requires separating the two muffler tailpipe connector nuts while removing both nuts along with the gasket. The muffler-tailpipe assembly must be separated from both front exhaust hanger isolators before cutting the exhaust system according to specifications. Remove the front muffler section by disconnecting the two exhaust hanger isolators followed by the rear muffler section. Install the exhaust hanger isolators with attention to their correct specification to prevent damage to the components. Inspection for wear and fatigue should occur and damaged parts require immediate replacement. Start with the installation of a non-tightened front muffler service section using a service clamp. The next step involves placing the rear muffler service section followed by hanger isolator attachment on the rear exhaust. The front section of the muffler requires a service clamp that connects to the rear section before installation of four exhaust hanger isolators on the front assembly. The service clamps should be tightened to reach 47 Nm (35 lb-ft) torque. The installation of non-PZEV requires a new gasket between the catalytic converter and muffler and tailpipe assembly with two new nuts tightened up to 47 Nm (35 lb-ft). To install the exhaust flexible pipe on PZEV vehicles users must use new gasket installation between the muffler and tailpipe assembly while tightening two new nuts to 47 Nm (35 lb-ft). Terminate support to the exhaust flexible pipe while making sure the conduit remains straight and not twisted since both issues may harm the system.

OEM Ford Focus Tail Pipe

Exhaust Tail Pipe

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

29 Tail Pipes found

View related parts
Ford Focus Exhaust Pipe Part Number: 9S4Z-5255-A
$221.23 MSRP: $306.04
You Save: $84.81 (28%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Pipe - Exhaust; Exhaust Tail Pipe; Tailpipe; Tail Pipe
- Replaces: 8S4Z-5255-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2008-2011 Ford Focus | S, SE, SEL, SES | 4 Cyl 2.0 L GAS
View related parts
Ford Focus Exhaust Pipe, Rear Part Number: F1FZ-5230-V
$377.05 MSRP: $495.82
You Save: $118.77 (24%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Pipe - Exhaust; Exhaust Intermediate Pipe, Rear; Tail Pipe; Muffler; Center Muffler
- Position: Rear
- Replaces: F1FZ-5230-B
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2015-2018 Ford Focus | S, SE, SEL, Titanium | 3 Cyl 1.0 L GAS, 4 Cyl 2.0 L FLEX, 4 Cyl 2.0 L GAS
View related parts
Ford Focus Rear Muffler Part Number: CV6Z-5A289-A
$187.27 MSRP: $258.81
You Save: $71.54 (28%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Muffler Assembly - Rear; Exhaust Muffler; Exhaust Muffler Assembly; Muffler
- Position: Rear
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2012-2018 Ford Focus | SE, SEL, Titanium | 3 Cyl 1.0 L GAS, 4 Cyl 2.0 L FLEX, 4 Cyl 2.0 L GAS
View related parts
Ford Focus Flex Tube Part Number: 7S4Z-5G203-A
$677.68 MSRP: $937.50
You Save: $259.82 (28%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Tube Assembly; Exhaust Pipe; Flex Pipe
- Replaces: 6S4Z-5G203-AA, 6S4Z-5G232-AA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2006-2007 Ford Focus | S, SE, SES, ZX3, ZX4, ZX5, ZXW | 4 Cyl 2.0 L GAS
View related parts
Ford Focus Exhaust Pipe Part Number: YS4Z-5G203-AA
$17.27 MSRP: $23.89
You Save: $6.62 (28%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Tube Assembly; Direct-Fit Exhaust; Exhaust System Kit; Flex Pipe; Flex Tube
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2000-2004 Ford Focus | LX, SE | 4 Cyl 2.0 L GAS
View related parts
Ford Focus Exhaust Pipe Part Number: YS4Z-5G203-BB
$142.38 MSRP: $196.97
You Save: $54.59 (28%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Tube Assembly; Flex Pipe; Flex Tube
- Manufacturer Note: Flex tube
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2000-2004 Ford Focus | LX, SE, Sony Limited Edition, SVT, ZTS, ZTW, ZX3, ZX5 | 4 Cyl 2.0 L GAS, 4 Cyl 2.3 L GAS
View related parts
Ford Focus Rear Muffler Part Number: 3S4Z-5A289-AA
$733.15 MSRP: $1014.24
You Save: $281.09 (28%)
ADD TO CART
Product Specifications
- Other Name: Muffler Assembly - Rear; Exhaust Muffler; Direct-Fit Exhaust; Exhaust System Kit; Muffler
- Manufacturer Note: Rear Muffler
- Position: Rear
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2003-2007 Ford Focus | S, SE, SES, ST, ZX3, ZX4 ST, ZX5 | 4 Cyl 2.0 L GAS, 4 Cyl 2.3 L GAS
View related parts
Ford Focus Tailpipe Extension Part Number: YS4Z-5K238-BA
$97.73 MSRP: $132.99
You Save: $35.26 (27%)
ADD TO CART
Product Specifications
- Other Name: Extension - Exhaust; Exhaust Tail Pipe; Exhaust System; Exhaust Pipe; Extension - Exhaust Pipe; Tail Pipe
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2000-2005 Ford Focus | LX, SE, Sony Limited Edition, SVT, ZTS, ZTW, ZX3, ZX4 ST, ZX5 | 4 Cyl 2.0 L GAS, 4 Cyl 2.3 L GAS
View related parts
Ford Focus Tailpipe Extension Part Number: 6S4Z-5255-AA
$59.38 MSRP: $80.80
You Save: $21.42 (27%)
ADD TO CART
Product Specifications
- Other Name: Pipe - Exhaust; Exhaust Tail Pipe; Direct-Fit Exhaust; Exhaust System Kit; Exhaust System; Exhaust Pipe; Tail Pipe
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2005-2007 Ford Focus | S, SE, SES, ST, ZX3, ZX4, ZX4 ST, ZX5, ZXW | 4 Cyl 2.0 L GAS, 4 Cyl 2.3 L GAS
View related parts
Ford Focus Tailpipe Extension Part Number: YS4Z-5K238-AA
Product Specifications
- Other Name: Extension - Exhaust; Exhaust Tail Pipe; Exhaust System; Exhaust Pipe; Extension - Exhaust Pipe; Tail Pipe
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2000-2005 Ford Focus | LX, SE, Sony Limited Edition, SVT, ZTS, ZTW, ZX3, ZX4 ST, ZX5 | 4 Cyl 2.0 L GAS, 4 Cyl 2.3 L GAS
View related parts
Ford Focus Rear Muffler Part Number: 3S4Z-5A289-BB
Product Specifications
- Other Name: Muffler Assembly - Rear; Exhaust Muffler; Direct-Fit Exhaust; Exhaust System Kit; Muffler
- Manufacturer Note: Rear Muffler
- Position: Rear
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2003-2007 Ford Focus | LX, S, SE, SES, ST, ZTS, ZX4 ST | 4 Cyl 2.0 L GAS, 4 Cyl 2.3 L GAS
View related parts
Ford Focus Exhaust Pipe Part Number: 3S4Z-5G203-BA
Product Specifications
- Other Name: Tube Assembly; Flex Pipe; Flex Tube
- Manufacturer Note: Flex tube, automatic transmission
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2003-2004 Ford Focus | LX, SE, ZTS, ZTW, ZX3, ZX5 | 4 Cyl 2.3 L GAS
View related parts
Ford Focus Exhaust Pipe Part Number: 3S4Z-5G203-CA
Product Specifications
- Other Name: Tube Assembly; Flex Pipe; Flex Tube
- Manufacturer Note: Flex tube, manual transmission
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2003-2004 Ford Focus | LX, SE, ZTS, ZTW, ZX3, ZX5 | 4 Cyl 2.3 L GAS
View related parts
Ford Focus Tailpipe Part Number: 6S4Z-5255-CA
Product Specifications
- Other Name: Pipe - Exhaust; Exhaust Tail Pipe; Exhaust Pipe; Tail Pipe
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2006-2007 Ford Focus | ST, ZX4 ST | 4 Cyl 2.3 L GAS
View related parts
Ford Focus Flex Tube Part Number: 7S4Z-5G203-B
Product Specifications
- Other Name: Tube Assembly; Exhaust Manifold; Flex Pipe; Manifold
- Replaces: 6S4Z-5G203-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2005-2007 Ford Focus | S, SE, SES, ZX3, ZX4, ZX5, ZXW | 4 Cyl 2.0 L GAS
View related parts
Ford Focus Muffler, Rear Part Number: 8S4Z-5A289-B
Product Specifications
- Other Name: Muffler Assembly - Rear; Exhaust Muffler
- Position: Rear
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2008-2011 Ford Focus | S, SE, SEL, SES | 4 Cyl 2.0 L GAS
View related parts
Ford Focus Rear Muffler Part Number: 8S4Z-5A289-C
Product Specifications
- Other Name: Muffler Assembly - Rear; Exhaust Muffler; Muffler
- Position: Rear
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2008-2011 Ford Focus | S, SE, SEL, SES | 4 Cyl 2.0 L GAS
View related parts
Ford Focus Rear Muffler Part Number: YS4Z-5A289-AA
Product Specifications
- Other Name: Muffler Assembly - Rear; Exhaust Muffler; Muffler
- Position: Rear
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2000-2004 Ford Focus | LX, SE, ZTS, ZTW, ZX3, ZX5 | 4 Cyl 2.0 L GAS, 4 Cyl 2.3 L GAS
View related parts
Ford Focus Rear Muffler Part Number: YS4Z-5A289-AB
Product Specifications
- Other Name: Muffler Assembly - Rear; Exhaust Muffler; Muffler
- Position: Rear
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2000-2004 Ford Focus | LX, SE, ZTS, ZTW, ZX3, ZX5 | 4 Cyl 2.0 L GAS
View related parts
Ford Focus Rear Muffler Part Number: YS4Z-5A289-AGA
Product Specifications
- Other Name: Muffler Assembly - Rear; Exhaust Muffler; Direct-Fit Exhaust; Exhaust System Kit; Muffler
- Position: Rear
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2000-2004 Ford Focus | LX, SE, Sony Limited Edition, ZTS | 4 Cyl 2.0 L GAS

| Page 1 of 2 |Next >

1-20 of 29 Results

Ford Focus Tail Pipe

OEM Tail Pipe boasts unmatched quality. Each part goes through full quality checks. They adhere to Ford's official factory standards. These steps remove flaws and inconsistencies. So you can get Tail Pipe with long life and a perfect fit. Come to our website and find genuine Ford Focus parts. We keep a wide inventory of OEM Focus parts at the highly affordable prices. It's easy to search, compare, and pick what you need. You'll love the clear info and simple checkout. We offer top-rated customer service, and we reply fast. We also ship promptly to ensure your order arrives on time.

The Tail Pipe is actually an exhaust system of Ford Focus which is made explicitly to direct exhaust gaseous emitted out of the engine to the rear of the car, thus effectively venting into atmosphere. Being a well-known car maker, Ford offers the Tail Pipe that not only improves productivity of the car but also boosts its look and sometimes it can raise chromed tips. The practicality of adaptation is also a major point to consider since the Tail Pipe is produced to be installed in different Focus models; right-side exhausts for Japanese markets and left-side for European ones. This flexibility not only optimizes the Focus's drive but also assumes a critical function of guaranteeing the smooth flow of exhaust for safety. The Tail Pipe comes in several attachment styles that make it easy to fit and several style of the pipe can be welded on the car. Also, the Tail Pipe constitutes a positive image in the market place both in terms of utility value and artistic elegance that expresses quality. Recent Focus models have incorporated improved techniques in relation to the cars' productivity and with the help of the Tail Pipe these cars are excellent for driving for those individuals who are seeking durable and fashionable cars as the Ford Focus. Altogether, the Tail Pipe is an example of more careful and attentive approach of the brand, demonstrating the company's constant strive for innovation and effective solutions for the clientele.

Ford Focus Tail Pipe Parts and Q&A

Exhaust Pipe
7S4Z-5G203-C
Q: What Are the Differences in Tail Pipe and Muffler Assembly Construction Between the Production and Service Version for PZEV and Non-PZEV on Ford Focus?
A:
The production muffler and tailpipe assembly is built into one piece but the service version contains three pieces for Partial Zero Emissions Vehicles (PZEV) and two pieces for non-PZEV. The installation of service sections requires the production exhaust system to be cut at an accurate position before moving forward. Position the vehicle at neutral mode on a hoist. A support wrap or splint must be added around the exhaust flexible pipe to stop bending or twisting that would harm the pipe. The PZEV removal procedure includes taking out the two exhaust flexible pipe nuts which must be discarded alongside the gasket. The removal process for non-PZEV requires separating the two muffler tailpipe connector nuts while removing both nuts along with the gasket. The muffler-tailpipe assembly must be separated from both front exhaust hanger isolators before cutting the exhaust system according to specifications. Remove the front muffler section by disconnecting the two exhaust hanger isolators followed by the rear muffler section. Install the exhaust hanger isolators with attention to their correct specification to prevent damage to the components. Inspection for wear and fatigue should occur and damaged parts require immediate replacement. Start with the installation of a non-tightened front muffler service section using a service clamp. The next step involves placing the rear muffler service section followed by hanger isolator attachment on the rear exhaust. The front section of the muffler requires a service clamp that connects to the rear section before installation of four exhaust hanger isolators on the front assembly. The service clamps should be tightened to reach 47 Nm (35 lb-ft) torque. The installation of non-PZEV requires a new gasket between the Catalytic Converter and muffler and tailpipe assembly with two new nuts tightened up to 47 Nm (35 lb-ft). To install the exhaust flexible pipe on PZEV vehicles users must use new gasket installation between the muffler and tailpipe assembly while tightening two new nuts to 47 Nm (35 lb-ft). Terminate support to the exhaust flexible pipe while making sure the conduit remains straight and not twisted since both issues may harm the system.