How to service the front bumper cover on Ford Windstar?

The service procedure of the front bumper cover begins with the removal of pin-type retainers together with screws that extend to both sides of the fixture. You should first pull down the front corner splash shield from both sides before you take off the nuts that are installed there. According to the maintenance procedure, press the tabs located at the upper corners of front bumper cover (part number 17D957) before removing the front bumper cover section. Enter the side marker lamp removal process after detaching its electrical connection and unfastening its nuts. First detach the matte finish front bumper grille (part number 17B968) alongside the lower radiator splash shield. Customers need to take off their chrome garnish moulding before continuing with the modification work. Follow the removal procedure to install these components in the reverse order.

How to remove the front bumper cover on Ford Windstar?

The process of removing the front bumper cover begins with disassembling pin-type retainers and screws alongside six screws that are divided into three on each side. The installation process requires removal of both additional J-nuts and four splash shield screws which allows setting aside the splash shields. You should next remove the four front bumper cover nuts from the wheel opening by taking out two nuts on each side. One must detach electrical connectors that service side lamps whenever they are applicable (each side requires a single connector). The installation requires users to disconnect two tabs positioned at the upper front bumper cover corners that are found one on each side and after this disconnection to remove the front bumper cover. Installation requires following the opposite order of removal actions and transferring required components.

OEM Ford Windstar Bumper

Bumper Fascia

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

23 Bumpers found

View related parts
Ford Windstar Impact Bar, Front Part Number: 3F2Z-17757-AA
$104.39 MSRP: $142.06
You Save: $37.67 (27%)
ADD TO CART
Product Specifications
- Other Name: Bumper Assembly - Front; Bumper Impact Bar, Front
- Position: Front
- Replaces: XF2Z-17757-AA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1999-2003 Ford Windstar | 3.0L, Base, Limited, LX, SE, SE Sport, SEL | 6 Cyl 3.0 L GAS, 6 Cyl 3.8 L GAS
View related parts
Ford Windstar Impact Bar Part Number: XF2Z-17906-AA
$79.02 MSRP: $109.32
You Save: $30.30 (28%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bumper
- Manufacturer Note: Bar only , order 17K835 cover separately
- Replaces: F68Z-17906-AA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1995-2003 Ford Windstar | 3.0L, Base, GL, Limited, LX, SE, SE Sport, SEL | 6 Cyl 3.0 L GAS, 6 Cyl 3.8 L GAS
View related parts
Ford Windstar Bumper Cover Part Number: 2F2Z-17K835-JAA
$306.87 MSRP: $421.03
You Save: $114.16 (28%)
ADD TO CART
Product Specifications
- Other Name: Cover
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2002-2003 Ford Windstar | Base, Limited, LX | 6 Cyl 3.8 L GAS
View related parts
Ford Windstar Bumper Cover Part Number: YF2Z-17K835-AA
$185.99 MSRP: $253.10
You Save: $67.11 (27%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Cover
- Manufacturer Note: Primed, smooth - includes integral step pad, must drill holes for w/park aid. completely interchangeable with YF2Z 17K835-BA, SE, SEL, Limited - w/ or w/o reverse park aid
- Replaces: YF2Z-17B807-EA, YF2Z-17K835-BA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1999-2003 Ford Windstar | 3.0L, Base, Limited, LX, SE, SE Sport, SEL | 6 Cyl 3.0 L GAS, 6 Cyl 3.8 L GAS
View related parts
Ford Windstar Bumper Cover, Harvest Gold Part Number: XF2Z-17K835-AAA
Product Specifications
- Other Name: Cover
- Manufacturer Note: Harvest Gold - must drill holes for w/park aid, Base(GL), LX - w/ or w/o reverse park aid, used w/ (B2) Harvest Gold
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1999-2001 Ford Windstar | 3.0L, Base, Limited, LX | 6 Cyl 3.0 L GAS, 6 Cyl 3.8 L GAS
View related parts
Ford Windstar Bumper Cover, Steel Blue Part Number: XF2Z-17K835-AAB
Product Specifications
- Other Name: Cover
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1999-2001 Ford Windstar | 3.0L, Base, Limited, LX | 6 Cyl 3.0 L GAS, 6 Cyl 3.8 L GAS
View related parts
Ford Windstar Bumper Cover, Blue Part Number: YF2Z-17D957-GB
Product Specifications
- Other Name: Cover
- Manufacturer Note: Med. Steel Blue (lower); Paint to match (upper)- use with LA, SP paint codes, Base, LX
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1999-2000 Ford Windstar | 3.0L, Base, Limited, LX | 6 Cyl 3.0 L GAS, 6 Cyl 3.8 L GAS
View related parts
Ford Windstar Bumper Cover Part Number: F68Z-17K835-CA
Product Specifications
- Other Name: Cover
- Manufacturer Note: When replaceing cover for units built before 07/01/96, order 96/ 17B807., FROM 07/01/96
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1995-1998 Ford Windstar | 3.0L, Base, GL, Limited, LX | 6 Cyl 3.0 L GAS, 6 Cyl 3.8 L GAS
View related parts
Ford Windstar Bumper Cover Part Number: F78Z-17D957-HF
Product Specifications
- Other Name: Cover
- Manufacturer Note: Primed - paint to match, Base, GL & LX
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1998 Ford Windstar | 3.0L, Base, GL, Limited, LX | 6 Cyl 3.0 L GAS, 6 Cyl 3.8 L GAS
View related parts
Ford Windstar Bumper Cover, Green Part Number: XF2Z-17K835-AAC
Product Specifications
- Other Name: Cover
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1999-2003 Ford Windstar | 3.0L, Base, Limited, LX | 6 Cyl 3.0 L GAS, 6 Cyl 3.8 L GAS
View related parts
Ford Windstar Bumper Cover, Neutral Gray Part Number: XF2Z-17K835-AAD
Product Specifications
- Other Name: Cover
- Replaces: YF2Z-17K835-CAA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1999-2001 Ford Windstar | 3.0L, Base, Limited, LX | 6 Cyl 3.0 L GAS, 6 Cyl 3.8 L GAS
View related parts
Ford Windstar Bumper Cover, Green Part Number: YF2Z-17D957-HB
Product Specifications
- Other Name: Cover
- Manufacturer Note: Winter Green (lower); Paint to Match (upper)- use with FS, PA paint codes, Base, LX
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1999-2000 Ford Windstar | 3.0L, Base, Limited, LX | 6 Cyl 3.0 L GAS, 6 Cyl 3.8 L GAS
View related parts
Ford Windstar Bumper Cover, Gold Part Number: YF2Z-17D957-JB
Product Specifications
- Other Name: Cover
- Manufacturer Note: Harvest Gold (lower); Paint to match (upper)- use with B2 paint code, Base, LX
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1999-2000 Ford Windstar | 3.0L, Base, Limited, LX | 6 Cyl 3.0 L GAS, 6 Cyl 3.8 L GAS
View related parts
Ford Windstar Bumper Cover, Gray Part Number: YF2Z-17D957-LB
Product Specifications
- Other Name: Cover
- Manufacturer Note: Neutral Grey (lower); paint to match (upper)- use with B4, D6, FL, TS, UA, WT paint codes, Base, LX
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1999-2000 Ford Windstar | 3.0L, Base, Limited, LX | 6 Cyl 3.0 L GAS, 6 Cyl 3.8 L GAS
View related parts
Ford Windstar Bumper Cover, Gold Part Number: 1F2Z-17D957-HAA
Product Specifications
- Other Name: Cover
- Manufacturer Note: Harvest Gold (lower cover) use with (B2) paint code for upper half of cover: paint to match, Base, LX, GL
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2001-2003 Ford Windstar | Base, Limited, LX, SE Sport | 6 Cyl 3.8 L GAS
View related parts
Ford Windstar Bumper Cover, Green Part Number: 1F2Z-17D957-HAB
Product Specifications
- Other Name: Cover
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2001-2003 Ford Windstar | Base, Limited, LX, SE Sport | 6 Cyl 3.8 L GAS
View related parts
Ford Windstar Bumper Cover, Gray Part Number: 1F2Z-17D957-HAC
Product Specifications
- Other Name: Cover
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2001-2003 Ford Windstar | Base, Limited, LX, SE Sport | 6 Cyl 3.8 L GAS
View related parts
Ford Windstar Bumper Cover Part Number: 1F2Z-17D957-JAA
Product Specifications
- Other Name: Cover
- Manufacturer Note: Black (lower cover) - for upper half of cover: paint to match, SE Sport
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2001 Ford Windstar | SE Sport | 6 Cyl 3.8 L GAS
View related parts
Ford Windstar Bumper Cover Part Number: 1F2Z-17D957-KAA
Product Specifications
- Other Name: Cover
- Replaces: YF2Z-17D957-KB
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1999-2003 Ford Windstar | 3.0L, Base, Limited, LX, SE, SE Sport, SEL | 6 Cyl 3.0 L GAS, 6 Cyl 3.8 L GAS
View related parts
Ford Windstar Bumper Cover Part Number: 1F2Z-17K835-GAA
Product Specifications
- Other Name: Cover
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2001-2002 Ford Windstar | SE Sport | 6 Cyl 3.8 L GAS

| Page 1 of 2 |Next >

1-20 of 23 Results

Ford Windstar Bumper

OEM Bumper boasts unmatched quality. Each part goes through full quality checks. They adhere to Ford's official factory standards. These steps remove flaws and inconsistencies. So you can get Bumper with long life and a perfect fit. Come to our website and find genuine Ford Windstar parts. We keep a wide inventory of OEM Windstar parts at the highly affordable prices. It's easy to search, compare, and pick what you need. You'll love the clear info and simple checkout. We offer top-rated customer service, and we reply fast. We also ship promptly to ensure your order arrives on time.

Ford Windstar Bumper Parts and Q&A

Impact Bar
XF2Z-17906-AA
Q: How to service the front bumper cover on Ford Windstar?
A:
The service procedure of the front bumper cover begins with the removal of pin-type retainers together with screws that extend to both sides of the fixture. You should first pull down the front corner splash shield from both sides before you take off the nuts that are installed there. According to the maintenance procedure, press the tabs located at the upper corners of front bumper cover (part number 17D957) before removing the front bumper cover section. Enter the side marker lamp removal process after detaching its electrical connection and unfastening its nuts. First detach the matte finish front bumper grille (part number 17B968) alongside the lower radiator splash shield. Customers need to take off their chrome garnish moulding before continuing with the modification work. Follow the removal procedure to install these components in the reverse order.
Bumper Cover, Gold
1F2Z-17D957-HAA
Q: How to remove the front bumper cover on Ford Windstar?
A:
The process of removing the front bumper cover begins with disassembling pin-type retainers and screws alongside six screws that are divided into three on each side. The installation process requires removal of both additional J-nuts and four splash shield screws which allows setting aside the splash shields. You should next remove the four front bumper cover nuts from the wheel opening by taking out two nuts on each side. One must detach electrical connectors that service side lamps whenever they are applicable (each side requires a single connector). The installation requires users to disconnect two tabs positioned at the upper front bumper cover corners that are found one on each side and after this disconnection to remove the front bumper cover. Installation requires following the opposite order of removal actions and transferring required components.