How to remove and replace the front bumper cover on Lincoln Town Car?

The first step to replace the front bumper cover includes removing five pin-type retainers and one radiator upper sight shield. Install the vehicle onto a hoist while keeping it in the neutral gear position. The next step involves disconnecting the 2 lower radiator air deflector-to-radiator support bolts but tighten them to 4 Nm (35 lb-in) when reinstalling them. Start by removing the lower radiator air deflector bolts that total eight in number and taking off these air deflectors before reinstallation where you need to fasten them to 4 Nm (35 lb-in). Remove the 6 bumper cover-to-fender nuts that belong to each side before reinstalling them with an appropriate torque setting of 7 Nm (62 lb-in). Disconnection of electrical connectors must be performed when fog lamps exist on the vehicle. For correct installation of the front bumper cover tighten its two side bolts to 4 Nm (35 lb-in). You should remove and then tighten the 2 screw attachments of the front bumper cover to the vertical shield at 4 Nm (35 lb-in) when reinstalling them. The bumper cover removal process ends when you push out both retaining tabs on the sides and take off the front bumper cover. Installation of the new bumper cover requires repeating the steps used in removal.

How to service and repair the front bumper cover on Lincoln Town Car?

Service and repair of the front bumper cover requires first removing the 5 pin-type retainers and the radiator upper sight shield. Install the vehicle in neutral gear on a hoist prior to taking out the 2 lower radiator air deflector-to-radiator support bolts that need to be tightened to 4 Nm (35 lb-in) when reinstalling. The service begins with removing the 8 lower radiator air deflector bolts along with the air deflectors before tightening them to 4 Nm (35 lb-in) torque during the installation process. The installation process requires us to tighten the 3 bumper cover-to-fender nuts on each side to 7 Nm (62 lb-in). Users must detach the electrical connectors whenever their vehicle comes with fog lamps installed. First remove the two screws that secure the front bumper cover at its sides before uninstalling the two screws attaching it to the vertical shields. Install both screws with a torque of 4 Nm (35 lb-in). Start by placing the bumper cover sides in an outward direction before using your fingers to depress the two retaining tabs and take off the front cover. The installation of the bumper cover requires performing the opposite steps used during removal.

OEM Lincoln Town Car Bumper Cover

Bumper Shell

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

8 Bumper Covers found

View related parts
Lincoln Town Car Bumper Cover, Front Part Number: 3W1Z-17D957-DA
$199.78 MSRP: $290.80
You Save: $91.02 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Cover; Bumper Cover, Front
- Position: Front
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2003-2011 Lincoln Town Car | Cartier, Cartier L, Designer Series, Executive, Executive L, Executive Protection Series, Protection Series, Signature, Signature L, Signature Limited, Ultimate, Ultimate L | 8 Cyl 4.6 L FLEX, 8 Cyl 4.6 L GAS
View related parts
Lincoln Town Car Bumper Cover, Rear Part Number: 3W1Z-17K835-FA
$247.18 MSRP: $362.97
You Save: $115.79 (32%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Cover; Bumper Cover, Rear
- Position: Rear
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2003-2005 Lincoln Town Car | Cartier, Cartier L, Executive, Executive L, Executive Protection Series, Protection Series, Signature, Signature L, Signature Limited, Ultimate, Ultimate L | 8 Cyl 4.6 L GAS
View related parts
Lincoln Town Car Bumper Cover, Rear Part Number: 6W1Z-17K835-APTM
$283.75 MSRP: $416.67
You Save: $132.92 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Cover; Bumper Cover, Rear
- Manufacturer Note: (CP) Designates Crash Part - When Ordering Please Refer To Crash Part Truckload Program Guidelines
- Position: Rear
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2006-2011 Lincoln Town Car | Designer Series, Executive, Executive L, Protection Series, Signature, Signature L, Signature Limited | 8 Cyl 4.6 L FLEX, 8 Cyl 4.6 L GAS
View related parts
Lincoln Town Car Bumper Cover, Front Part Number: 3W1Z-17D957-EA
$390.76 MSRP: $511.22
You Save: $120.46 (24%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Cover; Bumper Cover, Front
- Position: Front
- Replaces: 6W1Z-17D957-APTM
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2003-2007 Lincoln Town Car | Base, Cartier, Cartier L, Designer Series, Executive, Executive L, Executive Protection Series, Protection Series, Signature, Signature L, Signature Limited, Ultimate, Ultimate L | 4.6L V8, 8 Cyl 4.6 L FLEX, 8 Cyl 4.6 L GAS
View related parts
Lincoln Town Car Bumper Cover Part Number: F8VZ-17K835-BA
Product Specifications
- Other Name: Cover
- Manufacturer Note: Paint to match
- Replaces: XW1Z-17K835-AAA, XW1Z-17K835-CAA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1998-2002 Lincoln Town Car | Cartier, Cartier L, Executive, Executive L, Signature | 8 Cyl 4.6 L GAS
View related parts
Lincoln Town Car Bumper Cover Part Number: F8VZ-17D957-BA
Product Specifications
- Other Name: Cover
- Manufacturer Note: Paint to match
- Replaces: F8VZ-17D957-CAA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1998-2002 Lincoln Town Car | Cartier, Cartier L, Executive, Executive L, Signature | 4.6L V8, 8 Cyl 4.6 L GAS
View related parts
Lincoln Town Car Bumper Cover, Front Part Number: F5VY-17K835-A
Product Specifications
- Other Name: Bumper Assembly - Front
- Manufacturer Note: Paint to match
- Position: Front
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1995-1997 Lincoln Town Car | Anniversary, Base, Cartier, Cypress, Executive, Signature, Touring Edition | 8 Cyl 4.6 L GAS
View related parts
Lincoln Town Car Bumper Cover Part Number: 3W1Z-17K835-BA
Product Specifications
- Other Name: Cover
- Manufacturer Note: w/o reverse proximity
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2003-2005 Lincoln Town Car | Cartier, Cartier L, Executive, Executive L, Executive Protection Series, Protection Series, Signature, Signature L, Signature Limited, Ultimate, Ultimate L | 8 Cyl 4.6 L GAS

Lincoln Town Car Bumper Cover

OEM Bumper Cover boasts unmatched quality. Each part goes through full quality checks. They adhere to Lincoln's official factory standards. These steps remove flaws and inconsistencies. So you can get Bumper Cover with long life and a perfect fit. Come to our website and find genuine Lincoln Town Car parts. We keep a wide inventory of OEM Town Car parts at the highly affordable prices. It's easy to search, compare, and pick what you need. You'll love the clear info and simple checkout. We offer top-rated customer service, and we reply fast. We also ship promptly to ensure your order arrives on time.

The Bumper Cover is the soft outer panel that sits over the structural bumper to give the vehicle a finished appearance. The Bumper Cover can be positioned at the front or rear of the vehicle and may have shaped openings for directing air through the radiator, oil coolers, or brakes. It also offers mounting locations for fog lights, parking lights, or turning signals, allowing those lights to align uniformly with the surrounding trim for more aerodynamic airflow. Decorative inserts, grille pieces, and caps in small sections can snap into this Bumper Cover to close off unused light or tow-hook cavities, allowing surface continuity. The component of the Lincoln Town Car sedan is made of plastic to make it slightly flexible when there is minor contact. Replacement of the Bumper Cover is done for the restoration of protection and appearance when it cracks, fades, or gets damaged in a collision. The cost of this procedure varies widely depending on the provisions of components and body type. The Bumper Cover design serves the same cosmetic and safety function on each Lincoln Town Car. It reinforces the Town Car name's association with refinement in the Lincoln lineup.

Lincoln Town Car Bumper Cover Parts and Q&A

Bumper Cover, Front
3W1Z-17D957-DA
Q: How to remove and replace the front bumper cover on Lincoln Town Car?
A:
The first step to replace the front bumper cover includes removing five pin-type retainers and one radiator upper sight shield. Install the vehicle onto a hoist while keeping it in the neutral gear position. The next step involves disconnecting the 2 lower radiator Air Deflector-to-radiator support bolts but tighten them to 4 Nm (35 lb-in) when reinstalling them. Start by removing the lower radiator air deflector bolts that total eight in number and taking off these air deflectors before reinstallation where you need to fasten them to 4 Nm (35 lb-in). Remove the 6 bumper cover-to-fender nuts that belong to each side before reinstalling them with an appropriate torque setting of 7 Nm (62 lb-in). Disconnection of electrical connectors must be performed when fog lamps exist on the vehicle. For correct installation of the front bumper cover tighten its two side bolts to 4 Nm (35 lb-in). You should remove and then tighten the 2 screw attachments of the front bumper cover to the vertical shield at 4 Nm (35 lb-in) when reinstalling them. The bumper cover removal process ends when you push out both retaining tabs on the sides and take off the front bumper cover. Installation of the new bumper cover requires repeating the steps used in removal.
Bumper Cover, Front
3W1Z-17D957-EA
Q: How to service and repair the front bumper cover on Lincoln Town Car?
A:
Service and repair of the front bumper cover requires first removing the 5 pin-type retainers and the radiator upper sight shield. Install the vehicle in neutral gear on a hoist prior to taking out the 2 lower radiator Air Deflector-to-radiator support bolts that need to be tightened to 4 Nm (35 lb-in) when reinstalling. The service begins with removing the 8 lower radiator air deflector bolts along with the air deflectors before tightening them to 4 Nm (35 lb-in) torque during the installation process. The installation process requires us to tighten the 3 bumper cover-to-fender nuts on each side to 7 Nm (62 lb-in). Users must detach the electrical connectors whenever their vehicle comes with fog lamps installed. First remove the two screws that secure the front bumper cover at its sides before uninstalling the two screws attaching it to the vertical shields. Install both screws with a torque of 4 Nm (35 lb-in). Start by placing the bumper cover sides in an outward direction before using your fingers to depress the two retaining tabs and take off the front cover. The installation of the bumper cover requires performing the opposite steps used during removal.