What precautions should be taken before removing and installing the shock absorber on Mercury Grand Marquis?

The shock absorber installation process should start with turning off electricity to prevent sudden air spring expansion or deflation which may cause the vehicle to shift. Follow the procedure to deactivate the air suspension service switch. The center nut stays in place since removing it would cause spring tension loss which creates potential hazards for personal safety. Start by removing the nuts initially followed by discarding them then remove the wheel assembly together with the tire. First remove the bolts to set aside caliper pads with their anchor plate before you remove the brake disc. A hex holding tool should be used to stop the stud from rotating when removing and disposing the nut. Perform this operation again to remove both nuts and stabilizer bar link and dispose of the nuts. Apply the hex holding feature once more to remove and throw out the nut. Perform the nut and flag bolt removal then get rid of the part along with the nut. After completing shock absorber and spring assembly removal the installation process follows the reverse steps.

How to remove and replace the rear shock absorber on Mercury Grand Marquis?

The first step for replacing the rear shock absorber demands turning off electricity to air suspension to avoid unintended air spring inflation or deflation because such changes could trigger vehicle shift while servicing. All vehicles containing fire suppression systems need to have their depowering function completed before moving forward. Position the car in neutral gear then set it on a hoist after supporting the rear axle through appropriate jack stands or a suitable jack. After removing the upper shock nut together with the washer and insulator you should discard these components followed by new part installation where the upper nut gets tightened to 40 Nm (30 lb-ft). The shock absorber installation requires removal of the lower shock nut and bolt followed by installation of the new absorber part where the nut must be tightened to 90 Nm (66 lb-ft). After finishing the installation you must trigger the fire suppression system if your vehicle contains one. Shock absorber replacement requires identical fasteners to their original part number or essential equivalent models since inferior parts or substitute designs will deteriorate performance and raise maintenance expenditures. The correct retention of components depends on following all specified torque values during reassembly operations. The installation of shock absorbers happens one by one and manufacturers do not require you to replace absorbents in sets.

OEM Mercury Grand Marquis Shock Absorber

Suspension Shock Absorber

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

17 Shock Absorbers found

View related parts
Mercury Grand Marquis Shock Absorber, Blue/Green, Rear Part Number: BW7Z-18125-B
$94.37 MSRP: $155.27
You Save: $60.90 (40%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Shock Absorber Assembly; Rear Suspension Shock; Strut & Shock Kit; Air to Coil Conversion; Complete Strut; Shock; Suspension Shock Absorber
- Position: Rear
- Replaces: 3U2Z-18125-AF, 3W7Z-18125-FA, 4W7Z-18125-CA, 6W7Z-18125-C, 6W7Z-18125-B, 7W7Z-18125-B, 7W7Z-18125-C, 8W1Z-18125-D, 8W1Z-18125-B, 8W1Z-18125-C, ASH-1040, ASH-1039, ASH-24535, ASH-1151, ASH-24490, 7W1Z-18125-G, ASH-710, 3U2Z-18125-AB, ASH-12276, BW7Z-18125-A, 8W1Z-18125-A, ASH-24534, ASH-24491
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2006-2011 Mercury Grand Marquis | GS, LS | 8 Cyl 4.6 L FLEX, 8 Cyl 4.6 L GAS
View related parts
Mercury Grand Marquis Shock Absorber, Gray/Red, Rear Part Number: 8W7Z-18125-D
$89.67 MSRP: $150.55
You Save: $60.88 (41%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Shock Absorber Assembly; Suspension Shock Absorber, Rear; Shock
- Position: Rear
- Replaces: 4W3Z-18125-AA, 6W7Z-18125-D, 6W1Z-18125-A, 7W7Z-18125-D, 8W3Z-18125-A, 8W7Z-18125-B, ASH-1152, ASH-24537, ASH-711, 7W1Z-18125-A, ASH-12275, 3W7Z-18125-GA, 4W7Z-18125-DA, 3U2Z-18125-AC, 7W3Z-18125-H, 8W7Z-18125-C, ASH-24538, ASH-1038, ASH-24536, ASH-267, ASH-1041
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2006-2011 Mercury Grand Marquis | GS, LS | 8 Cyl 4.6 L FLEX, 8 Cyl 4.6 L GAS
View related parts
Mercury Grand Marquis Shock Absorber Part Number: BW7Z-18124-A
$116.03 MSRP: $190.91
You Save: $74.88 (40%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Shock Absorber Assembly; Suspension Strut and Shock Absorber Kit; Air Spring to Coil Spring Conversion; Complete Strut.; Strut; Shock
- Replaces: 7W7Z-18124-H, ASH-1035, 6W7Z-18124-B, 6W7Z-18124-D, ASH-24529, 7W7Z-18124-A, BW7Z-18124-B, 6W7Z-18124-A, 7W7Z-18124-C, 7W7Z-18124-D, ASH-1037, ASH-1036, ASH-12274
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2006-2011 Mercury Grand Marquis | GS, LS | 8 Cyl 4.6 L FLEX, 8 Cyl 4.6 L GAS
View related parts
Mercury Grand Marquis Shock Absorber, Driver Side Part Number: FOAZ-18125-B
$103.66 MSRP: $141.06
You Save: $37.40 (27%)
ADD TO CART
Product Specifications
- Other Name: Shock Absorber Assembly; Suspension Strut and Shock Assembly Kit; Air to Coil Spring Conversion; Complete Strut.; Shock
- Position: Driver Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1990-1991 Mercury Grand Marquis | GS, LS | 8 Cyl 5.0 L GAS
View related parts
Mercury Grand Marquis Shock Absorber Part Number: 9W1Z-18124-A
Product Specifications
- Other Name: Shock Absorber Assembly; Suspension Strut and Shock Absorber Kit; Air Spring to Coil Spring Conversion; Complete Strut.; Strut; Shock
- Replaces: 6W1Z-18124-A, ASH-1034, 7W1Z-18124-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2007-2011 Mercury Grand Marquis | GS, LS | 8 Cyl 4.6 L FLEX, 8 Cyl 4.6 L GAS
View related parts
Mercury Grand Marquis Shock Absorber Part Number: 5U2Z-18V125-C
Product Specifications
- Other Name: Kit - Shock Absorber; Suspension Shock Absorber Kit; Suspension Shock Absorber; Shock
- Replaces: 5U2Z-18V125-VF, 3U2Z-18125-BA, E7PZ-18125-A, F7AZ-18125-JA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1984-1999 Mercury Grand Marquis | Base, Colony Park, GS, LS | 8 Cyl 4.6 L GAS, 8 Cyl 5.0 L GAS, 8 Cyl 5.8 L GAS
View related parts
Mercury Grand Marquis Shock Absorber Part Number: 5U2Z-18V124-ND
Product Specifications
- Other Name: Kit - Shock Absorber
- Manufacturer Note: RH & LH - Retail, except Police, always replace in pairs
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1984-1991 Mercury Grand Marquis | Base, Colony Park, GS, LS | 8 Cyl 5.0 L GAS, 8 Cyl 5.8 L GAS
View related parts
Mercury Grand Marquis Shock Absorber Part Number: XW7Z-18125-B
Product Specifications
- Other Name: Kit - Shock Absorber; Shock
- Replaces: AA-527, AA-524, AA-526, ASH-24679, ASH-24680, XW7Z-18125-BB, XW7Z-18125-A, 1W7Z-18125-A, F8VZ-18125-AA, XW1Z-18125-AB, XW7Z-18125-AB
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1998-2002 Mercury Grand Marquis | GS, LS | 8 Cyl 4.6 L GAS
View related parts
Mercury Grand Marquis Shock Absorber Part Number: XW7Z-18124-BB
Product Specifications
- Other Name: Kit - Shock Absorber; Air Spring to Coil Spring Conversion.; Shock
- Manufacturer Note: RH & LH, with handling package
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1998-2002 Mercury Grand Marquis | GS, LS | 8 Cyl 4.6 L GAS
View related parts
Mercury Grand Marquis Shock Absorber, Rear Part Number: 3U2Z-18125-AD
Product Specifications
- Other Name: Shock Absorber Assembly; Suspension Shock Absorber, Rear; Shock
- Manufacturer Note: RH or LH, "White" (replacing 3W7Z-18125-DA), standard suspension, BEFORE 12/01/03
- Position: Rear
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2003-2006 Mercury Grand Marquis | GS, GSL, Limited Edition, LS, LSE, Ultimate Edition | 8 Cyl 4.6 L FLEX, 8 Cyl 4.6 L GAS
View related parts
Mercury Grand Marquis Shock Absorber, Front Part Number: 3U2Z-18124-BK
Product Specifications
- Other Name: Shock Absorber Assembly; Strut; Shock Absorber Assembly - Front
- Manufacturer Note: RH & LH (replacing 3W7Z-18124-BA), with sport equipment package, BEFORE 12/01/03
- Position: Front
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2003-2006 Mercury Grand Marquis | GS, GSL, Limited Edition, LS, LSE, Ultimate Edition | 8 Cyl 4.6 L FLEX, 8 Cyl 4.6 L GAS
View related parts
Mercury Grand Marquis Shock Absorber Part Number: 5U2Z-18V124-ZL
Product Specifications
- Other Name: Kit - Shock Absorber; Shock
- Replaces: ASHV-1009, XW7Z-18124-AA, F8AZ-18124-HA, 5U2Z-18V124-ZF, F7AZ-18124-BA, AS-2026-G, XW1Z-18124-AA, 3U2Z-18124-AA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1992-2001 Mercury Grand Marquis | GS, LS | 8 Cyl 4.6 L GAS
View related parts
Mercury Grand Marquis Shock Absorber, Passenger Side Part Number: FOAZ-18125-A
Product Specifications
- Other Name: Shock Absorber Assembly; Suspension Strut and Shock Assembly Kit; Air to Coil Spring Conversion; Complete Strut.; Shock
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1990-1991 Mercury Grand Marquis | GS, LS | 8 Cyl 5.0 L GAS
View related parts
Mercury Grand Marquis Shock Absorber Part Number: XW7Z-18125-CA
Product Specifications
- Other Name: Kit - Shock Absorber; Air Spring to Coil Spring Conversion; Suspension Kit.; Shock
- Manufacturer Note: RH or LH, with air springs
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1992-1999 Mercury Grand Marquis | GS, LS | 8 Cyl 4.6 L GAS
View related parts
Mercury Grand Marquis Shock Absorber Part Number: XW3Z-18125-AA
Product Specifications
- Other Name: Shock Absorber Assembly; Suspension Strut and Shock Assembly Kit; Air to Coil Spring Conversion; Complete Strut.; Shock
- Manufacturer Note: RH or LH, contains the F8MZ-18125-AA shock and the mounting kit., performance suspension
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1998-2002 Mercury Grand Marquis | GS, LS | 8 Cyl 4.6 L GAS
View related parts
Mercury Grand Marquis Shock Absorber, Front Part Number: 3U2Z-18124-BJ
Product Specifications
- Other Name: Shock Absorber Assembly; Strut; Shock Absorber Assembly - Front
- Manufacturer Note: RH & LH, "White" (replacing 3W7Z,18124,AA) , base, standard duty suspension, BEFORE 12/01/03
- Position: Front
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2003-2007 Mercury Grand Marquis | GS, GSL, Limited Edition, LS, LSE, Ultimate Edition | 8 Cyl 4.6 L FLEX, 8 Cyl 4.6 L GAS
View related parts
Mercury Grand Marquis Shock Absorber Part Number: F8AZ-18124-CA
Product Specifications
- Other Name: Shock Absorber Assembly; Air Spring to Coil Spring Conversion Kit; Suspension Kit.; Shock
- Manufacturer Note: RH & LH, heavy duty/Police/Taxi
- Replaces: AS-2028, ASH-24678, AS-1094-G, XW3Z-18124-AA, F8VZ-18124-AA, 3U2Z-18124-ZA, ASH-702, XW7Z-18124-A, XW7Z-18124-AB, F8AZ-18124-AA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1998-2002 Mercury Grand Marquis | GS, LS | 8 Cyl 4.6 L GAS

Mercury Grand Marquis Shock Absorber

OEM Shock Absorber boasts unmatched quality. Each part goes through full quality checks. They adhere to Mercury's official factory standards. These steps remove flaws and inconsistencies. So you can get Shock Absorber with long life and a perfect fit. Come to our website and find genuine Mercury Grand Marquis parts. We keep a wide inventory of OEM Grand Marquis parts at the highly affordable prices. It's easy to search, compare, and pick what you need. You'll love the clear info and simple checkout. We offer top-rated customer service, and we reply fast. We also ship promptly to ensure your order arrives on time.

The Shock Absorber of Mercury Grand Marquis vehicles is one of the most important part and act in conjunction with the strut in the suspension system to enhance stability and control. These components assist to reduce hopping and isolate shock forces and lessen the passage of jerks, enhance the ride and comfort levels. In the subsequent years, different types of shock absorbers evolved and are categorized into twin tube and mono tube types, and the hydraulic fluid control is different depending on the kind of driving style it is tailored for. Also, the new technologies such as the electrorheological and magnetorheological dampers have enabled semi-active as well as adaptive suspensions to improve comfort as well as control on the roads.

Mercury Grand Marquis Shock Absorber Parts and Q&A

Shock Absorber, Front
3U2Z-18124-BK
Q: What precautions should be taken before removing and installing the shock absorber on Mercury Grand Marquis?
A:
The shock absorber installation process should start with turning off electricity to prevent sudden air spring expansion or deflation which may cause the vehicle to shift. Follow the procedure to deactivate the Air Suspension service switch. The center nut stays in place since removing it would cause spring tension loss which creates potential hazards for personal safety. Start by removing the nuts initially followed by discarding them then remove the wheel assembly together with the tire. First remove the bolts to set aside caliper pads with their anchor plate before you remove the Brake Disc. A hex holding tool should be used to stop the stud from rotating when removing and disposing the nut. Perform this operation again to remove both nuts and stabilizer bar link and dispose of the nuts. Apply the hex holding feature once more to remove and throw out the nut. Perform the nut and flag bolt removal then get rid of the part along with the nut. After completing shock absorber and spring assembly removal the installation process follows the reverse steps.
Shock Absorber, Gray/Red, Rear
8W7Z-18125-D
Q: How to remove and replace the rear shock absorber on Mercury Grand Marquis?
A:
The first step for replacing the rear shock absorber demands turning off electricity to Air Suspension to avoid unintended air spring inflation or deflation because such changes could trigger vehicle shift while servicing. All vehicles containing fire suppression systems need to have their depowering function completed before moving forward. Position the car in neutral gear then set it on a hoist after supporting the rear axle through appropriate jack stands or a suitable jack. After removing the upper shock nut together with the washer and insulator you should discard these components followed by new part installation where the upper nut gets tightened to 40 Nm (30 lb-ft). The shock absorber installation requires removal of the lower shock nut and bolt followed by installation of the new absorber part where the nut must be tightened to 90 Nm (66 lb-ft). After finishing the installation you must trigger the fire suppression system if your vehicle contains one. Shock absorber replacement requires identical fasteners to their original part number or essential equivalent models since inferior parts or substitute designs will deteriorate performance and raise maintenance expenditures. The correct retention of components depends on following all specified torque values during reassembly operations. The installation of shock absorbers happens one by one and manufacturers do not require you to replace absorbents in sets.