How to Service the Rear 60 Percent Backrest Seat Cover on Mercury Sable?

The service process for the Taurus and Sable rear 60 percent seat backrest cover starts by taking out the 60 percent rear seat backrest first. Pressing the button on the head restraint control will free up the head restraint unit. Begin by removing the screw and the armrest bracket outboard cover. Next uninstall the armrest-to-bracket bolt while you tighten it to 23 Nm (17 lb-ft) upon reinstalling it. Detach the armrest by sliding the pin on its inboard side from the backrest and then fold up and set aside the armrest pocket panel of the trim cover. Lift out the pin-type retainers while releasing the J-clip at the bottom of the backrest trim cover and unfasten the hook-and-loop strips at its rear. Tearing the seat backrest foam occurs when correctly separating the hook-and-loop strip from the cover. First detach the hook-and-loop strips before turning the trim cover inside-out. Afterward cut away the three rows of hog rings and draw the latch release strap through the trimmed material. First lift the backrest foam pad and then pinch the head restraint guide while taking off its two guides before you remove the backrest trim cover. The finishing step will reverse the steps used for removal.

How to Service and Repair the Front Seat Cover on Mercury Sable?

Owner service and repair of front seat cushion covers begins by removing the front seat while pulling out manual recline controls and power recliner knobs when present on the vehicle. Power seat service requires removing the seat control switch knob followed by releasing the pin-type retainer which connects the switch wire harness to remove the control switch from the side shield while moving the shield to the side. Start by taking out the rear screw and dividing the side shield before releasing all fixings on the cushion trim cover edge. You should remove the hog rings together with the seat cushion trim cover while keeping the safety belt buckle facing through the trim cover opening for proper installation. Repower the SRS system following the reverse installation sequence yet omit proof testing unless the service involved the passenger seat. The Occupant Classification Sensor (OCS) system reset process should begin only after finishing all front passenger seat repairs and verifying correct assembly of components. The new OCS system service kit requires complete installation under conditions where OCSM receives voltage between 8-18 volts and temperature falls within 6°C to 36°C. The reset procedure needs to be performed when the passenger seat is empty while waiting for at least 8 seconds since turning the ignition switch to ON. Checks of the OCS system connector along with wiring, pressure sensor hose and seat-related wiring must be conducted if the first reset attempt does not work. After the initial reset cycle the ignition switch once more while performing a second reset. A new OCS system service kit becomes necessary when both resets fail. The SRS needs to be proven out by turning the ignition first to OFF then waiting 10 seconds before returning it to ON while watching the warning indicator. The system needs to illuminate for six seconds and afterward it must switch itself off. An indicator fault results in three possible cases: no light, persistent light and flashing along with a chime when the indicator does not function correctly. A scan tool needs to remove all ongoing DTCs from both the RCM and OCSM.

OEM Mercury Sable Seat Cover

Car Seat Protector Cover

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

62 Seat Covers found

View related parts
Mercury Sable Seat Back Cover, Passenger Side Part Number: 5F4Z-5464416-CAB
Product Specifications
- Other Name: Cover Assembly - Seat Back
- Manufacturer Note: R.H., w/o side impact air bag, FROM 9/20/04
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2004-2005 Mercury Sable | GS, LS, LS Premium, Platinum Edition | 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS
View related parts
Mercury Sable Seat Back Cover, Rear Driver Side Part Number: 5F4Z-5466601-AAA
Product Specifications
- Other Name: Cover Assembly - Rear Seat; Cover Assembly - Rear Seat Back
- Manufacturer Note: L.H., w/split seat back, FROM 9/20/04
- Position: Rear Driver Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2004-2005 Mercury Sable | GS, LS, LS Premium, Platinum Edition | 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS
View related parts
Mercury Sable Seat Cover, Passenger Side Part Number: 5F4Z-5462900-AAB
Product Specifications
- Other Name: Cover Assembly - Seat Cushion
- Manufacturer Note: R.H., FROM 9/17/04
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2004-2005 Mercury Sable | GS, LS, LS Premium, Platinum Edition | 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS
View related parts
Mercury Sable Seat Cover, Passenger Side Part Number: 5F4Z-5462900-BAB
Product Specifications
- Other Name: Cover Assembly - Seat Cushion
- Manufacturer Note: R.H., FROM 9/17/04
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2004-2005 Mercury Sable | GS, LS, LS Premium, Platinum Edition | 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS
View related parts
Mercury Sable Seat Cover, Driver Side Part Number: 5F4Z-5462901-AAB
Product Specifications
- Other Name: Cover Assembly - Seat Cushion
- Manufacturer Note: L.H., FROM 9/17/04
- Position: Driver Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2004-2005 Mercury Sable | GS, LS, LS Premium, Platinum Edition | 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS
View related parts
Mercury Sable Seat Cover, Driver Side Part Number: 5F4Z-5462901-BAB
Product Specifications
- Other Name: Cover Assembly - Seat Cushion
- Manufacturer Note: L.H., FROM 9/17/04
- Position: Driver Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2004-2005 Mercury Sable | GS, LS, LS Premium, Platinum Edition | 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS
View related parts
Mercury Sable Seat Back Cover, Passenger Side Part Number: 5F4Z-5464416-AAB
Product Specifications
- Other Name: Cover Assembly - Seat Back
- Manufacturer Note: R.H., w/o side impact air bag, FROM 9/20/04
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2005 Mercury Sable | GS, LS, Platinum Edition | 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS
View related parts
Mercury Sable Seat Back Cover, Passenger Side Part Number: 5F4Z-5464416-BAA
Product Specifications
- Other Name: Cover Assembly - Seat Back
- Manufacturer Note: R.H., w/side impact air bag, FROM 9/20/04
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2004 Mercury Sable | GS, LS Premium | 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS
View related parts
Mercury Sable Seat Back Cover, Passenger Side Part Number: 5F4Z-5464416-BAB
Product Specifications
- Other Name: Cover Assembly - Seat Back
- Manufacturer Note: R.H., w/side impact air bag, FROM 9/20/04
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2005 Mercury Sable | GS, LS, Platinum Edition | 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS
View related parts
Mercury Sable Seat Back Cover, Passenger Side Part Number: 5F4Z-5464416-DAB
Product Specifications
- Other Name: Cover Assembly - Seat Back
- Manufacturer Note: R.H., w/side impact air bag, FROM 9/20/04
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2004-2005 Mercury Sable | GS, LS, LS Premium, Platinum Edition | 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS
View related parts
Mercury Sable Seat Back Cover, Driver Side Part Number: 5F4Z-5464417-AAA
Product Specifications
- Other Name: Cover Assembly - Seat Back
- Manufacturer Note: L.H., w/side impact air bag, FROM 9/20/04
- Position: Driver Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2004 Mercury Sable | GS, LS Premium | 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS
View related parts
Mercury Sable Seat Back Cover, Driver Side Part Number: 5F4Z-5464417-AAB
Product Specifications
- Other Name: Cover Assembly - Seat Back
- Manufacturer Note: L.H., w/side impact air bag, FROM 9/20/04
- Position: Driver Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2005 Mercury Sable | GS, LS, Platinum Edition | 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS
View related parts
Mercury Sable Seat Back Cover, Driver Side Part Number: 5F4Z-5464417-BAB
Product Specifications
- Other Name: Cover Assembly - Seat Back
- Manufacturer Note: L.H., w/o side impact air bag, FROM 9/20/04
- Position: Driver Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2005 Mercury Sable | GS, LS, Platinum Edition | 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS
View related parts
Mercury Sable Seat Back Cover, Driver Side Part Number: 5F4Z-5464417-CAB
Product Specifications
- Other Name: Cover Assembly - Seat Back
- Manufacturer Note: L.H., w/o side impact air bag, FROM 9/20/04
- Position: Driver Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2004-2005 Mercury Sable | GS, LS, LS Premium, Platinum Edition | 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS
View related parts
Mercury Sable Seat Back Cover, Driver Side Part Number: 5F4Z-5464417-DAB
Product Specifications
- Other Name: Cover Assembly - Seat Back
- Manufacturer Note: L.H., w/side impact air bag, FROM 9/20/04
- Position: Driver Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2004-2005 Mercury Sable | GS, LS, LS Premium, Platinum Edition | 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS
View related parts
Mercury Sable Seat Back Cover, Rear Passenger Side Part Number: 5F4Z-5466600-AAA
Product Specifications
- Other Name: Cover Assembly - Rear Seat; Cover Assembly - Rear Seat Back
- Manufacturer Note: R.H., w/split seat back, FROM 9/20/04
- Position: Rear Passenger Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2004-2005 Mercury Sable | GS, LS, LS Premium, Platinum Edition | 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS
View related parts
Mercury Sable Seat Back Cover, Rear Passenger Side Part Number: 5F4Z-5466600-BAB
Product Specifications
- Other Name: Cover Assembly - Rear Seat; Cover Assembly - Rear Seat Back
- Manufacturer Note: R.H., FROM 9/20/04
- Position: Rear Passenger Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2004-2005 Mercury Sable | GS, LS, LS Premium, Platinum Edition | 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS
View related parts
Mercury Sable Seat Back Cover, Rear Driver Side Part Number: 5F4Z-5466601-BAB
Product Specifications
- Other Name: Cover Assembly - Rear Seat; Cover Assembly - Rear Seat Back
- Manufacturer Note: L.H., FROM 9/20/04
- Position: Rear Driver Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2004-2005 Mercury Sable | GS, LS, LS Premium, Platinum Edition | 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS
View related parts
Mercury Sable Cushion Cover, Gray, Passenger Side Part Number: 8T5Z-5462900-AA
Product Specifications
- Other Name: Cover Assembly - Seat Cushion
- Manufacturer Note: (ML)
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2008-2009 Mercury Sable | Base, Premier | 6 Cyl 3.5 L GAS
View related parts
Mercury Sable Cushion Cover, Tan, Passenger Side Part Number: 8T5Z-5462900-AB
Product Specifications
- Other Name: Cover Assembly - Seat Cushion
- Manufacturer Note: (MJ) Light Camel
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2008-2009 Mercury Sable | Base, Premier | 6 Cyl 3.5 L GAS

| Page 1 of 4 |Next >

1-20 of 62 Results

Mercury Sable Seat Cover

OEM Seat Cover boasts unmatched quality. Each part goes through full quality checks. They adhere to Mercury's official factory standards. These steps remove flaws and inconsistencies. So you can get Seat Cover with long life and a perfect fit. Come to our website and find genuine Mercury Sable parts. We keep a wide inventory of OEM Sable parts at the highly affordable prices. It's easy to search, compare, and pick what you need. You'll love the clear info and simple checkout. We offer top-rated customer service, and we reply fast. We also ship promptly to ensure your order arrives on time.

Mercury Sable Seat Cover Parts and Q&A

Seat Back Cover, Tan, Passenger Side
8T5Z-5464416-AB
Q: How to Service the Rear 60 Percent Backrest Seat Cover on Mercury Sable?
A:
The service process for the Taurus and Sable rear 60 percent seat backrest cover starts by taking out the 60 percent rear seat backrest first. Pressing the button on the head restraint control will free up the head restraint unit. Begin by removing the screw and the armrest bracket outboard cover. Next uninstall the armrest-to-bracket bolt while you tighten it to 23 Nm (17 lb-ft) upon reinstalling it. Detach the armrest by sliding the pin on its inboard side from the backrest and then fold up and set aside the armrest pocket panel of the trim cover. Lift out the pin-type retainers while releasing the J-clip at the bottom of the backrest trim cover and unfasten the hook-and-loop strips at its rear. Tearing the seat backrest foam occurs when correctly separating the hook-and-loop strip from the cover. First detach the hook-and-loop strips before turning the trim cover inside-out. Afterward cut away the three rows of hog rings and draw the latch release strap through the trimmed material. First lift the backrest foam pad and then pinch the head restraint guide while taking off its two guides before you remove the backrest trim cover. The finishing step will reverse the steps used for removal.
Seat Back Cover, Gray, Driver Side
8T5Z-5464417-BA
Q: How to Service and Repair the Front Seat Cover on Mercury Sable?
A:
Owner service and repair of front seat cushion covers begins by removing the front seat while pulling out manual recline controls and power recliner knobs when present on the vehicle. Power seat service requires removing the seat control switch knob followed by releasing the pin-type retainer which connects the switch wire harness to remove the control switch from the side shield while moving the shield to the side. Start by taking out the rear screw and dividing the side shield before releasing all fixings on the cushion trim cover edge. You should remove the hog rings together with the seat cushion trim cover while keeping the safety belt buckle facing through the trim cover opening for proper installation. Repower the SRS system following the reverse installation sequence yet omit proof testing unless the service involved the passenger seat. The Occupant Classification Sensor (OCS) system reset process should begin only after finishing all front passenger seat repairs and verifying correct assembly of components. The new OCS system service kit requires complete installation under conditions where OCSM receives voltage between 8-18 volts and temperature falls within 6°C to 36°C. The reset procedure needs to be performed when the passenger seat is empty while waiting for at least 8 seconds since turning the ignition switch to ON. Checks of the OCS system connector along with wiring, pressure sensor hose and seat-related wiring must be conducted if the first reset attempt does not work. After the initial reset cycle the ignition switch once more while performing a second reset. A new OCS system service kit becomes necessary when both resets fail. The SRS needs to be proven out by turning the ignition first to OFF then waiting 10 seconds before returning it to ON while watching the warning indicator. The system needs to illuminate for six seconds and afterward it must switch itself off. An indicator fault results in three possible cases: no light, persistent light and flashing along with a chime when the indicator does not function correctly. A scan tool needs to remove all ongoing DTCs from both the RCM and OCSM.