Menu
×
Search Bar
Search by Part Number, Part Name, or Vehicle
My Garage
Cart
Help Center Contact Us
Make sure this part fits

Ford 8G1Z-7E395-D
Shift Control Cable

2009 Lincoln MKS 8G1Z7E395D

Customer Questions & Expert Answers (2)
Ford 8G1Z-7E395-D Shift Control Cable
  • Part Description
    Cable Assembly - Selector Lever Control; Automatic Transmission Shifter Cable
  • Base No.
    7E395
  • Replaces
    8G1Z-7E395-B
  • Manufacturer
    Ford
  • Manufacturer's Notes
    This part is discontinued.
Make sure this part fits

  • 8G1Z-7E395-D Shift Control Cable is Ref No. 6 in the diagram below

    2009 Lincoln MKS Shift Control Cable Diagram for 8G1Z-7E395-D
    The diagram listed above is for your reference. View diagram for your vehicle

    Related Parts for 8G1Z-7E395-D

  • Vehicle Fitment

    Year Make Model Trim Engine
    2009 Lincoln MKSBase6 Cyl 3.7 L GAS
    Warning: California's Proposition 65

  • Customer Questions & Expert Answers

    Q:
    Will this 8G1Z-7E395-D work in my car? Posted by FordPartsDeal Specialist
    A:
    Select Your Vehicle model to verify if part number 8G1Z-7E395-D fits your car.
    Posted by FordPartsDeal Specialist
    Q:
    How to Service and Repair the Shift Cable on Lincoln MKS? Posted by Customer
    A:
    Begin selecting and fixing the selector lever cable when the vehicle remains in NEUTRAL position while placed on a hoist. Start by removing the selector lever bezel before you can disconnect the selector lever cable end from its connection by pressing on the two-release tabs. The LH floor console finish panel should be removed next to reach the cable retainer and rubber grommet while you disconnect the selector lever cable retainer from the center console to extract the cable underneath the heater housing. Begin by removing nuts from the rubber grommet at the bulkhead then disconnect the Mass Air Flow (MAF) sensor electrical connector as well as unplug the engine breather from the Air Cleaner (ACL) assembly. The installer must remove the two assembly bolts from the ACL and loosen the outlet pipe clamp at the TB before extracting both parts. Disconnect the selector lever cable retainer both from the brake tube bracket and from the manual control lever end. Use your thumb to push the two tabs at the bracket which will extract the selector lever cable. Position the selector lever cable into the bracket opening of the vehicle before locking the tabs. Position the grommet with the selector lever cable retainer on the brake tube bracket before installing the two nuts that must achieve 7 Nm (62 lb-in) torque. Feed the selector lever cable beneath the heater housing before attaching the retainer to the center console while placing the floor console finish panel at its appropriate spot. The selector lever cable installation on selector lever housing requires proper tab locking before connecting the selector lever cable end to the selector lever. Position the DRIVE selection lever with the manual control lever before rotating the manual control lever until it reaches its stop position followed by operating it counterclockwise by one detent. You must unlock the adjuster by moving its locking tab before you will be able to line up the selector lever cable end with the manual control lever and make the connection when the adjuster locking tab is unlocked. First slide the adjuster lock to its position before locking it and fitting the ACL assembly into place then secure the two bolts by tightening them to 11 Nm (97 lb-in). Reconnect the engine breather to the ACL assembly, and the MAF sensor electrical connector after you tighten the outlet pipe at the TB to 5 Nm (44 lb-in). The installer needs to put on the selector lever bezel and selector lever knob then test the system to confirm PARK and NEUTRAL selection along with proper REVERSE lamp activation.
    Posted by FordPartsDeal Specialist
    If you have any questions about this product, please don't hesitate to ask us. We will be happy to help you!

OEM Ford Shift Control Cable 8G1Z-7E395-D Designed for Proper Fit and Performance

The Ford part 8G1Z-7E395-D Shift Control Cable as a genuine Ford Shift Cable component delivers both authenticity and reliability. This item carries a warranty from the manufacturer which guarantees 12-month, 12,000-mile of use. The Ford 8G1Z-7E395-D Shift Control Cable is used with Lincoln MKS models. The original Ford part will bear the manufacturer part number: 8G1Z-7E395-D and where it is made at Ford. It has the code: 7E395.
This component is approximately 1.60 Pounds. The part 8G1Z7E395D is available in New condition while meeting the standards of the product rating. The Cable Assembly - Selector Lever Control; Automatic Transmission Shifter Cable belongs to the Direct Replacement category to guarantee it is suitable for its specific vehicle applications. This part 8G1Z-7E395-D can be known as Cable, and it replaces 8G1Z-7E395-B. The inventory reference for this item is SKU: 8G1Z-7E395-D. The Ford manufacturer issues a factory warranty for this component which ensures dependable operation and peak performance. You can find delivery and returns information on our Shipping Policy and Return Policy pages.
Original equipment manufacturer parts are of the top standards and their performance is outstanding and top notch. This is explained by the fact that they follow the official manufacturing techniques of Ford, use of premium material and meets high standards of quality. Our site is worth visiting, in case you need high-quality and affordable OEM Ford components. We promise the optimal priced Ford parts on a wide range. You can relax that all OEM products you buy from us include a manufacturer warranty and will be covered by our simple and easy-to-use return policy, so you will not worry about buying a part.