Question 1

How to service and repair the floor shift cable and bracket on Lincoln Navigator?

Accepted Answer

Begin repair or servicing of the floor shift shift cable and bracket when the vehicle sits in neutral position on a hoist. When maintaining nameplates on Funkmaster Flex vehicles start by lifting slowly the lower right corner of the plate that displays its serial number to reach the tape and cut it with piano wire. The service for Expedition models requires removal of prndl trim together with console tray and cup holder insert followed by console upper trim screw. You must disconnect the shift cable from both ball stud and housing of the selector lever arm. It is necessary to begin with the Navigator models where technicians must remove selector lever trim plates along with floor console upper panels and disconnect shift cables from both selector lever arm ball stud and housing components. The installation procedure requires removal of the shift cable together with the rubber grommet while also taking out any present heat shield in case of vehicle equipment. Prevent any damage by never putting pressure on the shift cable between the manual control lever and the shift cable bracket. Contact the manual control lever ball stud by lifting the locking tab before you detach the shift cable from the ball stud. Following that you must remove the bracket bolts and shift cable clip which are situated on the transmission. Mount the shift cable bracket onto the transmission before fastening its bolts with torque set at 25 Nm (18 lb-ft). Install the shift cable by putting it around the ball stud on manual control lever while listening for an audible snap of the cable in place. Also lock the shift cable tabs when finished. The shift cable lock tab needs to be locked in place before installing or adding the required heat shield. Affix the shift cable to the housing and arm ball stud while listening for correct installation clicks since there should be two audible clicks during installation. The final step includes returning both the Expedition sequence of console upper trim, prndl trim, console tray, and cup holder insert and the Navigator sequence of center console LH kick panel and floor console upper panel. The name plate of Funkmaster Flex vehicles requires tape removal followed by double-sided tape application before returning it to the floor console finish panel position. Adjust the shift cable according to requirement.

Question 2

How to service and repair the shift cable on Lincoln Town Car?

Accepted Answer

Start service and repair of the shift cable by making sure you shut off the electrical power to air suspension because unexpected changes in air spring pressure could cause shifting during operations that risks personal injury. Begin by raising and supporting the vehicle and ending your operation by detaching the shift cable from the transmission through removal of its nut and separation from the shift cable bracket and manual control lever (7A256). The technician discards the shift cable retainer before unclipping the section of cable that runs through the engine compartment clips while removing the transmission bolts that anchor the shift cable bracket. Safely lower the vehicle then unclip the shift cable from its clip that directs toward the bulkhead. Users should detach the shift cable from the steering column through a disconnection process between the transmission selector lever arm and support (7302) and the steering column bracket while discarding the retainer. Apply a suitable tool to push the rubber grommet through the bulkhead before taking out the shift cable from the vehicle. The new shift cable goes through the bulkhead opening toward the transmission with proper seating of the rubber grommet. The shift cable installation requires attachment to the steering column followed by application of a new retainer before connecting it between the steering column bracket and transmission selector lever arm and support. The operator must move the gearshift lever (7210) to position (D) after suspending a 1.4 kg (3 lb) weight from it. Clamp the shift cable to the clip while leading it toward the bulkhead and then elevate the vehicle for support. First position the shift cable bracket and fasten its bolts to link the cable with the bracket but keep it detached from the manual control lever. The new shift cable retainer should be installed before connecting the cable to the bracket for attachment to the upward routing clips located in the engine compartment. Complete all required adjustments to the shift cable before enabling electrical power to the air suspension by placing the vehicle on the ground when equipped.

OEM Lincoln Shift Cable

34 Shift Cables found

Lincoln Shift Control Cable Part Number: YL3Z-7E395-AC

Lincoln Shift Control Cable Part Number: AA5Z-7E395-C

Lincoln Shift Control Cable Part Number: 7L1Z-7E395-D

Lincoln Shift Control Cable Part Number: 2C5Z-7E395-BB

Lincoln Shift Control Cable Part Number: 4C5Z-7E395-B

Lincoln Cable Assembly Part Number: BT4Z-7E395-A

Lincoln Shift Control Cable Part Number: EJ7Z-7E395-F

Lincoln Cable Assembly Part Number: CT4Z-7E395-C

Lincoln Shift Control Cable Part Number: DP5Z-7E395-H

Lincoln Shift Control Cable Part Number: KT4Z-7D246-N

Lincoln Shift Control Cable Part Number: F2GZ-7E395-AB

Lincoln Shift Control Cable Part Number: F2GZ-7E395-Y

Lincoln Shift Control Cable Part Number: F2GZ-7E395-Z

Lincoln Shift Control Cable Part Number: L1MZ-7D246-AE

Lincoln Shift Control Cable Part Number: KT4Z-7D246-T

Lincoln Shift Control Cable Part Number: AE9Z-7E395-C

Lincoln Shift Control Cable Part Number: FL1Z-7E395-B

Lincoln Shift Control Cable Part Number: 3W4Z-7E395-AA

Lincoln Shift Control Cable Part Number: 5L7Z-7E395-AA

Lincoln Shift Control Cable Part Number: XW4Z-7E395-AB

Lincoln Shift Cable

Lincoln Shift Cable Parts and Q&A

Related Lincoln Parts

Browse Lincoln Shift Cable by Models