Ford 4W7Z-9A758-AA
Throttle Cable

One must start maintenance or repairs on the accelerator pedal cable by removing the front engine appearance cover alongside the throttle return spring. The first step involves removing the accelerator cable from the throttle body lever before unscrewing the bracket attachment to detach the cable from its mounting point on the accelerator cable bracket. Pull out the accelerator cable both from its clip while also unfastening all the terminal nuts. You must disconnect the accelerator cable from the accelerator pedal and shaft where you can observe the fixed pedal design even though the actual pedal entails adjustment. Pull the cable through the dash panel after unclipping its retainer to evacuate the cable completely from inside the vehicle. To install the component follow all removal steps in reverse order.

Start the throttle cable and linkage servicing by disconnecting the ground cable of the battery and the electrical connector of the accelerator pedal sensor except for fixed pedal assemblies that do not function properly and exist without connection. Stage one requires disconnecting the accelerator pedal motor electrical connector followed by disconnecting the accelerator pedal motor drive cable connector when the system includes adjustable features. Remove the three nuts from the accelerator pedal retainer bracket before taking out the assembly together with the bracket. Position the accelerator pedal and bracket assembly so it can be installed by applying three retainer nuts at 9 Nm (80 lb-in). The procedure to install an accelerator pedal motor drive cable connector applies to vehicles that utilize adjustable accelerator pedal and bracket components. The service unit for fixed pedal and bracket assemblies differs from original specifications while the non-working accelerator pedal motor electrical connector requires different connection points according to harness length. Play the electrical connector for the accelerator pedal motor before plugging in the accelerator pedal sensor electrical connector and completing the battery ground connection. A proper indexing procedure should be followed when working on adjustable accelerator pedal and bracket assemblies.

Service and repair operations on throttle cable and linkage start by removing both the front engine appearance cover and the throttle return spring. First disconnect the accelerator cable from the throttle body lever followed by screw removal from the bracket and detachment of the cable from the accelerator cable bracket. Extract the accelerator cable out from its clip while removing the attached nuts. Disassemble the accelerator cable from both the pedal and shaft until the non-memory pedal is exposed although memory pedal solution is identical. Pull the cable through the dash panel by removing the accelerator cable retainer so you can take out the cable entirely from the vehicle. The installation process should consist of performing the removal steps in reverse order.

Begin the throttle cable maintenance by removing both the front engine appearance cover in addition to the throttle control spring. First remove the accelerator cable from the throttle body lever before disconnecting the screw that secures the cable to its bracket while you detach the accelerator cable from the accelerator cable bracket. The accelerator cable requires removal from its clip before the technician removes the nuts and the LH cowl extension bracket. To access the accelerator cable installation, remove it from both pedal components while paying attention to the non-memory pedal schematic that functions similarly to memory controls. Remove the accelerator cable retainer before taking out the cable and grommet from the bulkhead structure. Take the cable through the dash panel before finally extracting it out of the vehicle. To reinstall follow the backward method of removal steps.

Service and repair of throttle cables starts with front engine appearance cover removal together with the throttle control spring. Detach first the accelerator cable from the throttle body lever and unscrew the retaining screw from the bracket to pull the cable free from the accelerator cable bracket alignment. The accelerator cable requires removal from its clip before removing the nuts which also detach the LH cowl extension bracket. Begin the procedure by disconnecting the accelerator cable from the accelerator pedal and shaft but pay attention to the non-memory pedal prototype since the memory pedal matches this design. First remove the accelerator cable retainer then proceed by taking out the cable along with its grommet through the bulkhead. Finally extract the cable through the dash panel before taking it out of the vehicle. You should perform installation by conducting the steps in reverse order.

The first step to service throttle cable and linkage requires disconnecting the battery ground cable. A flat screwdriver should be implemented for gently removing the protective shell of the motor by rotating it between the shell and motor through the shell's opening. The drive cable/sensor assembly should be unfastened from the drive motor. New drive cable/sensor assembly installation requires connecting to the motor before removing the tie strap and aligning protective shell tabs with drive motor end-cap slots for complete tab insertion. To complete the repair process reconnect the battery ground cable then reposition the accelerator pedal assembly and its shaft. Maintenance technicians must install a new drive cable on accelerator pedal and shaft assemblies where the memory option exists since these assemblies contain adjustable drive cables. Indexing of the adjustable pedal system should always occur any time technicians service brake or accelerator pedal assemblies.

The first step for throttle cable and linkage repair services includes removing the front engine appearance cover and throttle return spring. You should begin by disconnecting the accelerator cable from the throttle body lever before removing its screw on the bracket to detach the cable from the accelerator cable bracket. First detach the accelerator cable from its clip before unattaching all the nuts. Extract the accelerator cable from the pedal assembly to shaft and make note of the fixed pedal design since an adjustable pedal design exists. The cable must pass through the dash panel after removing its retainer because you need to take it out entirely from the vehicle. Follow the reverse order of the removal process when installing the component.

A repair or service on the accelerator pedal cable requires starting with the front engine appearance cover and throttle return spring removal. Begin by removing the screw that fastens the cable to its bracket before detaching it from the throttle body lever. The next step includes disconnecting the accelerator cable from the accelerator cable bracket. Start by removing the cable from its clip before taking off the attaching nuts. The technician should disconnect the accelerator cable from both the accelerator pedal and shaft before proceeding while acknowledging the display of the non-memory pedal since the memory pedal configuration remains equivalent. Disembark the accelerator cable retainer and draw the cable through the dash panel until the entire system is free from the vehicle. Completion of installation requires you to perform the removal steps in reverse order.

Service of throttle cable and linkage starts with removing the front engine appearance cover and the throttle return spring. First detach the accelerator cable from the throttle body lever before removing the screw that fastens the cable to its bracket and finally removing the accelerator cable from the accelerator cable bracket. The first step entails extracting the accelerator cable out of its clip followed by removing its holding nuts. Remove the accelerator cable from the accelerator pedal and shaft while recognizing that the shown pedal is non-memory yet the memory pedal works in the same manner. The completion of cable removal requires firstly removing the retainer and pulling the cable onward through the dashboard so it exits the vehicle. Installation requires performing the opposite actions used for removal.