1994 Ford F-150 Transmission

Part Notes: (QQ-97) - 7" O.D. - .085" thick, retaining ring - 7B066 to cyl.
(QQ-97) 7" O.D. - .085" thick, retaining ring 7B066 to 7D044

Part Notes: (QQ-98-H) - 7" O.D. - .058" thick, retaining ring - 7B066 to cyl.
(QQ-98H) 7" O.D. - .058" thick, retaining ring 7B066 to 7A360
(QQ-98H) 7" O.D. - .058" thick, retaining ring 7B066 to 7D044

Part Notes: (QQ-92-J)-RING (7F235 TO 7F283) RETAINING 1 19/32"

Part Notes: (AB-187-KB) bolt (case to engine) - M10-1.50 x 65 (metric)

Part Notes: Bolt (case to engine) M10 - 1.50 x 75 (metric)

Part Notes: Note: 7A191 gasket not included with 7A098 screen, 4x4

Part Notes: Located on both sides of 7D006 planet - used with 4 pinion planetaries
Washer - thrust - plain style - located at between 7B067 and 7A398 - used with 4 pinion planetaries

Part Notes: Kit - drain plug in pan - includes reusable gasket, filter, 20 bolts, and I.S., All DSO applications only

Part Notes: O-ring - pump outer seal - 9 33/64" O.D. - green, yellow or orange stripe

Part Notes: (QQ-96) - ring - retainer - 6 21/32" - 1/16" thick
(QQ-96) ring (7B070 to 7A360) retaining 7" O.D. x .076" thick

Part Notes: (QQ-98-B) - 7" O.D. - .094" thick, retaining ring - 7B066 to cyl.
(QQ-98B) 7" O.D. - .094" thick, retaining ring 7B066 to 7A360
(QQ-98B) 7" O.D. - .094" thick, retaining ring 7B066 to 7D044

Part Notes: Internal - friction
Internal friction

Part Notes: 2 1/2" O.D. - short lip seal - forward clutch piston inner

Part Notes: #8c Thrust
2 3/16" I.D. x 2 7/8" O.D.

Part Notes: To be used when replacement 1996/ valve body is used

Part Notes: (QQ-94-A) ring (7B067 to 7D392) retaining 4 17/32" I.D. - 1/16" thick

Part Notes: Hub only - used with E9TZ 7D171-AA and E6DZ 7G178-A

Part Notes: Located between 7B067 and 7A398 planet - Located between 7A398 and 7D063 sun gear

Part Notes: 5/16" - Used without cooler bypass tube - use 7G118 & 7Z152 if equipted with cooler bypass tube
5/16", Transmission case

Part Notes: Includes "O" ring, 1/2 - 20 female x 1/4 NPTF male, for 5/16 diameter tube

Part Notes: Ltr. "C" stamp - .076" thick - 5 11/16" O.D.

Part Notes: #9 Thrust Bearing
2 13/16" O.D. - located between 7D164 hub and 7D171 race
Located between 7A658 shaft and 7A130 support

Part Notes: Note: If connector requires replacement use 14A464 kit as cataloged., Includes Trans Fluid Temp Sensor

Part Notes: (U-3-A) screw and washer (7H183 to 7A039) 1/4-20 x 0.62, 2/W/D

Part Notes: Plug - to block OSS/TSS hole in late E4OD service cases

Part Notes: Plug - speedometer hole, 4x2
Speed: All

Part Notes: Plug - rubber - located in bottom of transmission converter housing

Part Notes: .118 tooth thickness - 5.640/5.630 OD - use w/10 plate forward clutch

Part Notes: Apply side - 3.13-3.23mm Thick - 157.2-157.8mm I.D. - 26 teeth in a 30 tooth profile

Part Notes: Pressure - .250/.260" thick at snap ring surface

Part Notes: 3 3/4" dia - 3/64" thick
3 3/4" dia. x 3/64" thick

Part Notes: (Q-6-G)-ring (7D164 to 7060) retaining 1 13/16"

Part Notes: Kit - includes sensor (F5LP 7F293-AA), necessary spacers, grommet, sleeve and I.S., BEFORE 8/27/96

Part Notes: .219" thick - 34 teeth 3 21/32" ID x 5.00" OD 12 - plate clutch

Part Notes: Rear , 1 7/16" I.D. x 2" O.D. , (use as forward planet thrust bearing race)

Part Notes: (AB-91-E) bolt (7A103 to 7005) M8 x 1.25 x 65 hex head (metric)

Part Notes: (QQ-92-JJ)-ring (retain 7A527 in 7F207 cyl.) retaining-1 59/64"

Part Notes: 11/32" thick - 5 1/8" I.D. - 26 teeth
Direct drive clutch, forward clutch rear
Rear - 11/32" thick - 5 1/8" I.D. - 26 teeth

Part Notes: Forward clutch front - triangle depression on face of plate
Front - 19/64" thick - 5 1/8" I.d. - 26 teeth

Part Notes: 1 1/4" I.D. - short flair lip seal - direct clutch piston inner

Part Notes: To be used when replacement 1996/ valve body is used.

Part Notes: Ltr. "D" Stamp - .062" thick - 5 11/16" O.D.

Part Notes: Located on both sides of 7D006 - 3 tabs (15.0-15.5mm) - used with 3 pinion planetaries
Washer - thrust - plain style - 3 tabs (15.0-15.5mm) - located between 7B067 and 7A398 - used with 3 pnion planetaries

Part Notes: Ltr. "B" stamp - .090" thick - 5 11/16" O.D.

Part Notes: Ltr. "A" stamp - .104" thick - 5 11/16" O.D.

Part Notes: BEFORE 5/1/97
Race , used with E6DZ 7G178,A #9 thrust washer

Part Notes: Outer - flair lip seal - 8 13/32" OD x 7 29/32" ID