How to Service and Repair the Dual Converter Exhaust Pipe on All on 2002 Ford F-150?

Service or repair procedures on the dual converter Y-pipe need vehicle lifter support as the first step. Before proceeding with the service you need to remove both the muffler along with the tailpipe assembly and muffler extension pipe when present. The servicing process for 4.6L and 5.4L engine vehicles requires disconnecting the Heated Oxygen Sensors (H02S) and the catalyst monitor sensor but 4.2L engine vehicles do not need to remove the two upstream H02S located on the exhaust manifolds. Detach the electrical connector of the catalyst monitor sensor and unfasten four converter-to-manifold nuts. Removal of bolts and transfer case side plate becomes necessary when vehicles have this particular component installed. Rivet removal starting from two retaining bolts which connect the heat shield to the transmission support crossmember. Transmission support must occur only on the oil pan rails to minimize transmission harm and a suitable high-lift jack should be used for support. The next step requires removal of transmission support crossmember nuts as well as LH and RH bolts. Removal of a bolt represents the installation step for 5.4L engine vehicles yet 4.2L and 4.6L engines require nut removal. Conclude by removing the dual converter Y-pipe along with a separate nuts two-hand operation to detach the LH and RH converters if required. Installation completion includes performing the opposite procedure of what was carried out during removal.

OEM 2002 Ford F-150 Exhaust Pipe

Exhaust Tail Pipe

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

5 Exhaust Pipes found

View related parts
2002 Ford F-150 Intermediate Pipe, Front
Part Number: F85Z-5A212-BB
$67.71 MSRP: $92.14
You Save: $24.43 (27%)
ADD TO CART
Product Specifications
- Other Name: Pipe - Exhaust Front; Exhaust Pipe; Direct-Fit Exhaust; Exhaust System Kit; Intermed Pipe
- Position: Front
- Base No.: 5A212
- Item Weight: 6.30 Pounds
- Condition: New
- Fitment Type: Direct Replacement
- SKU: F85Z-5A212-BB
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2002 Ford F-150 Submodels:
- Base, Harley-Davidson Edition, King Ranch, Lariat, Lightning, XL, XLT | 6 Cyl 4.2 L GAS, 8 Cyl 4.6 L GAS, 8 Cyl 5.4 L BI-FUEL, 8 Cyl 5.4 L CNG, 8 Cyl 5.4 L GAS
View related parts
2002 Ford F-150 Tail Pipe Extension
Part Number: 7L3Z-5255-AB
Product Specifications
- Other Name: Pipe - Exhaust; Exhaust Tail Pipe; Exhaust Tip; Extension
- Replaces: 6L3Z-5255-AA
- Base No.: 5202
- Item Weight: 10.90 Pounds
- Item Dimensions: 8.0 x 17.7 x 13.5 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 7L3Z-5255-AB
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2002 Ford F-150 Submodels:
- Base, FX2, FX4, Harley-Davidson Edition, King Ranch, Lariat, Lightning, Limited, THE 60TH ANNIVERSARY EDITION, XL, XLT | 8 Cyl 5.4 L BI-FUEL, 8 Cyl 5.4 L CNG, 8 Cyl 5.4 L FLEX, 8 Cyl 5.4 L GAS
View related parts
2002 Ford F-150 Intermediate Pipe, Front
Part Number: XL3Z-5A212-CA
Product Specifications
- Other Name: Pipe - Exhaust Front; Exhaust Pipe; Direct-Fit Exhaust; Exhaust System Kit; Intermed Pipe; Pipe - Exhaust - Front
- Position: Front
- Base No.: 5A212
- Item Weight: 2.20 Pounds
- Condition: New
- Fitment Type: Direct Replacement
- SKU: XL3Z-5A212-CA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2002 Ford F-150 Submodels:
- Base, XL, XLT | 6 Cyl 4.2 L GAS
View related parts
2002 Ford F-150 Muffler W/Tpipe, Rear
Part Number: XL3Z-5230-BA
Product Specifications
- Other Name: Muffler And Pipe Assembly; Exhaust Muffler; Direct-Fit Exhaust; Exhaust System Kit; Exhaust Pipe; Muffler
- Position: Rear
- Replaces: 1L3Z-5230-BA, 1L3Z-5230-DA, YL3Z-5230-AA
- Item Weight: 21.00 Pounds
- Condition: New
- Fitment Type: Direct Replacement
- SKU: XL3Z-5230-BA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2002 Ford F-150 Submodels:
- Base, Harley-Davidson Edition, King Ranch, Lariat, Lightning, XL, XLT | 6 Cyl 4.2 L GAS, 8 Cyl 4.6 L GAS, 8 Cyl 5.4 L BI-FUEL, 8 Cyl 5.4 L CNG, 8 Cyl 5.4 L GAS
View related parts
2002 Ford F-150 Intermediate Pipe, Front
Part Number: F65Z5A212FA
Product Specifications
- Other Name: Pipe - Exhaust Front; Exhaust Pipe; Intermed Pipe
- Position: Front
- Item Weight: 4.50 Pounds
- Condition: New
- Fitment Type: Direct Replacement
- SKU: F65Z5A212FA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2002 Ford F-150 Submodels:
- Base, FX4, Harley-Davidson Edition, King Ranch, Lariat, Lightning, XL, XLT | 6 Cyl 4.2 L GAS, 8 Cyl 4.6 L GAS, 8 Cyl 5.4 L BI-FUEL, 8 Cyl 5.4 L CNG, 8 Cyl 5.4 L GAS

2002 Ford F-150 Exhaust Pipe

If you're seeking quality and affordability, look no further than our extensive inventory of genuine 2002 Ford F-150 Exhaust Pipe available at FordPartsDeal.com. You can confidently purchase our OEM 2002 Ford F-150 Exhaust Pipe as they are supported by the manufacturer's warranty and our hassle-free return policy, alongside the benefit of our fast delivery service.

2002 Ford F-150 Exhaust Pipe Parts Questions & Experts Answers

Q: How to Service and Repair the Dual Converter Exhaust Pipe on All on 2002 Ford F-150?
A: Service or repair procedures on the dual converter Y-pipe need vehicle lifter support as the first step. Before proceeding with the service you need to remove both the muffler along with the tailpipe assembly and muffler extension pipe when present. The servicing process for 4.6L and 5.4L engine vehicles requires disconnecting the Heated Oxygen Sensors (H02S) and the catalyst monitor sensor but 4.2L engine vehicles do not need to remove the two upstream H02S located on the exhaust manifolds. Detach the electrical connector of the catalyst monitor sensor and unfasten four converter-to-manifold nuts. Removal of bolts and transfer case side plate becomes necessary when vehicles have this particular component installed. Rivet removal starting from two retaining bolts which connect the heat shield to the transmission support crossmember. Transmission support must occur only on the oil pan rails to minimize transmission harm and a suitable high-lift jack should be used for support. The next step requires removal of transmission support crossmember nuts as well as LH and RH bolts. Removal of a bolt represents the installation step for 5.4L engine vehicles yet 4.2L and 4.6L engines require nut removal. Conclude by removing the dual converter Y-pipe along with a separate nuts two-hand operation to detach the LH and RH converters if required. Installation completion includes performing the opposite procedure of what was carried out during removal.