FordParts
My Garage
My Account
Cart
OEM 2002 Ford Ranger ABS Control Module
Anti Lock Brake Control Module- Select Vehicle by Model
- Select Vehicle by VIN
Select Vehicle by Model
orMake
Model
Year
Select Vehicle by VIN
For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).
3 ABS Control Modules found
2002 Ford Ranger Control Module
Part Number: 4L5Z-2C286-AAProduct Specifications- Other Name: Module; ABS Hydraulic Assembly; ABS Control Module; Modulator Valve; ABS Control Unit
- Replaces: 4L5Z-2C215-AA
- Base No.: 2C286
- Item Weight: 4.30 Pounds
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 4L5Z-2C286-AA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
2002 Ford Ranger Control Module
Part Number: 1L5Z-2C219-FAProduct Specifications- Other Name: Control; ABS Control Module
- Manufacturer Note: ECU, 4X4 - 4 wheel ABS
- Base No.: 2C219
- Item Weight: 1.60 Pounds
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 1L5Z-2C219-FA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
2002 Ford Ranger Control Module
Part Number: 1L5Z-2C219-EAProduct Specifications- Other Name: Control; ABS Control Module; Brake Proportioning Valve; Proportioner Valve
- Manufacturer Note: ECU, 4X2 - 4 wheel ABS
- Base No.: 2C219
- Item Weight: 1.60 Pounds
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 1L5Z-2C219-EA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
2002 Ford Ranger ABS Control Module
If you're seeking quality and affordability, look no further than our extensive inventory of genuine 2002 Ford Ranger ABS Control Module available at FordPartsDeal.com. You can confidently purchase our OEM 2002 Ford Ranger ABS Control Module as they are supported by the manufacturer's warranty and our hassle-free return policy, alongside the benefit of our fast delivery service.
2002 Ford Ranger ABS Control Module Parts Questions & Experts Answers
- Q: How to Bleed the Brake System After Installing a New ABS Control Module on 2002 Ford Ranger?A: The process of venting brake fluid from the system occurs through four steps after installing a new Hydraulic Control Unit (HCU) for Four Wheel Anti-Lock Brake System (4WABS). Start by connecting an NGS DCL cable adapter to the vehicle data link connector (DLC) under the dash then proceed with the NGS instructions for fluid bleeding. Proceed to clean the brake master cylinder filler cap before removing it to add brake fluid from the specified brake fluid list. A clear drain tube should be fastened to the RH rear bleeder screw while its other end rests in a brake fluid-filled container. An assistant should pump the brake pedal before maintaining firm pressure on it. To accomplish the RH rear bleeder screw bleeding you must begin with a fluid stream before tightening the screw when the assistant continues pressure on the pedal. Proceed with the bleeding process again without clearing or replacing brake fluid until slides of pure transparent fluid appear from the tap which signals to refill the master cylinder as required. Proceed with bleedings starting from the LH rear bleeder screw followed by the RH front bleeder screw and ending with the LH front bleeder screw. Another complete bleed procedure should be performed on each of the four corners using the standard technique.
Related 2002 Ford Ranger Parts
2002 Ford Ranger Brake Controller
2002 Ford Ranger Throttle Position Sensor
2002 Ford Ranger Ignition Coil
2002 Ford Ranger Relay
2002 Ford Ranger Brake Light Switch
2002 Ford Ranger Headlight Switch
2002 Ford Ranger Oil Pressure Switch
2002 Ford Ranger Spark Plug
2002 Ford Ranger Speedometer
2002 Ford Ranger ABS Pump And Motor Assembly
2002 Ford Ranger Back Up Light Switch
2002 Ford Ranger Car Key