How to Bleed the Brake System After Installing a New ABS Control Module on Ford Ranger?

The process of venting brake fluid from the system occurs through four steps after installing a new Hydraulic Control Unit (HCU) for Four Wheel Anti-Lock Brake System (4WABS). Start by connecting an NGS DCL cable adapter to the vehicle data link connector (DLC) under the dash then proceed with the NGS instructions for fluid bleeding. Proceed to clean the brake master cylinder filler cap before removing it to add brake fluid from the specified brake fluid list. A clear drain tube should be fastened to the RH rear bleeder screw while its other end rests in a brake fluid-filled container. An assistant should pump the brake pedal before maintaining firm pressure on it. To accomplish the RH rear bleeder screw bleeding you must begin with a fluid stream before tightening the screw when the assistant continues pressure on the pedal. Proceed with the bleeding process again without clearing or replacing brake fluid until slides of pure transparent fluid appear from the tap which signals to refill the master cylinder as required. Proceed with bleedings starting from the LH rear bleeder screw followed by the RH front bleeder screw and ending with the LH front bleeder screw. Another complete bleed procedure should be performed on each of the four corners using the standard technique.

How to Service and Repair the Rear ABS Control Module on Ford Ranger?

The service repair for Electronic Brake Control Module Antilock Control needs users to start by stripping the radio along with the center instrument panel finish panel and disconnecting the cigar lighter electrical connectors while removing all bolts. The first step in this procedure requires you to eliminate the instrument panel ash receptacle through bolt removal. Next step is to remove the anti-lock brake control module through bolt removal and deconnecting its electrical connector. The installation procedure should be performed in the opposite order of removal.

OEM Ford Ranger ABS Control Module

Anti Lock Brake Control Module

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

15 ABS Control Modules found

View related parts
Ford Ranger Control Module Part Number: XL2Z-2C219-BA
$269.00 MSRP: $364.62
You Save: $95.62 (27%)
ADD TO CART
Product Specifications
- Other Name: Control; ABS Control Module
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1999-2000 Ford Ranger | XL, XLT | 4 Cyl 2.5 L GAS, 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS, 6 Cyl 4.0 L GAS
View related parts
Ford Ranger Control Module Part Number: BL5Z-2C219-B
$1288.24 MSRP: $1761.69
You Save: $473.45 (27%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Control; ABS Control Module
- Replaces: AL5Z-2C219-B
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2010-2011 Ford Ranger | Sport, XL, XLT | 4 Cyl 2.3 L GAS, 6 Cyl 4.0 L GAS
View related parts
Ford Ranger Control Module Part Number: BL5Z-2C219-A
$1283.29 MSRP: $1754.92
You Save: $471.63 (27%)
ADD TO CART
Product Specifications
- Other Name: Control; ABS Control Module
- Replaces: AL5Z-2C219-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2010-2011 Ford Ranger | Sport, XL, XLT | 4 Cyl 2.3 L GAS, 6 Cyl 4.0 L GAS
View related parts
Ford Ranger Control Module Part Number: HB3Z-2C405-A
$951.64 MSRP: $1409.83
You Save: $458.19 (33%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Unit Assembly - Control; ABS Hydraulic Assembly; ABS Control Module; Modulator Valve
- Replaces: KB3Z-2C405-B
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2019-2023 Ford Ranger | Lariat, XL, XLT | 4 Cyl 2.3 L GAS
View related parts
Ford Ranger Control Module Part Number: 4L5Z-2C286-AA
Product Specifications
- Other Name: Module; ABS Hydraulic Assembly; ABS Control Module; Modulator Valve; ABS Control Unit
- Replaces: 4L5Z-2C215-AA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2001-2009 Ford Ranger | Edge, FX4, Sport, STX, Tremor, XL, XLT | 4 Cyl 2.3 L GAS, 4 Cyl 2.5 L GAS, 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS, 6 Cyl 4.0 L GAS
View related parts
Ford Ranger Pressure Valve Part Number: F87Z-2B373-AE
Product Specifications
- Other Name: Valve Assembly - Modulator; Brake Proportioning Valve; Modulator Valve; Valve Assembly; Proportioner Valve
- Replaces: F87Z-2B373-ARM
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1992-1997 Ford Ranger | Custom, S, Splash, Sport, STX, XL, XL Sport, XLT | 4 Cyl 2.3 L GAS, 6 Cyl 2.9 L GAS, 6 Cyl 3.0 L GAS, 6 Cyl 4.0 L GAS
View related parts
Ford Ranger Control Module Part Number: F57Z-2C219-A
Product Specifications
- Other Name: Module & Bracket Assembly; ABS Control Module; Module & Brkt Assembly-Power Steering
- Manufacturer Note: ECU, 4 wheel ABS
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1995-1997 Ford Ranger | Splash, Sport, STX, XL, XL Sport, XLT | 4 Cyl 2.3 L GAS, 6 Cyl 3.0 L GAS, 6 Cyl 4.0 L GAS
View related parts
Ford Ranger Modulator Valve Part Number: BL5Z-2C215-A
Product Specifications
- Other Name: Module; ABS Hydraulic Assembly; ABS Control Module; ABS Control Unit
- Replaces: AL5Z-2C215-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2010-2011 Ford Ranger | Sport, XL, XLT | 4 Cyl 2.3 L GAS, 6 Cyl 4.0 L GAS
View related parts
Ford Ranger Control Module Part Number: 4L5Z-2C219-BA
Product Specifications
- Other Name: Kit - Repair; ABS Control Module
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2004-2009 Ford Ranger | Edge, FX4, Sport, STX, Tremor, XL, XLT | 4 Cyl 2.3 L GAS, 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS, 6 Cyl 4.0 L GAS
View related parts
Ford Ranger Control Module Part Number: 4L5Z-2C219-AA
Product Specifications
- Other Name: Module - ABS Control; ABS Control Module
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2004-2009 Ford Ranger | Edge, FX4, Sport, STX, Tremor, XL, XLT | 4 Cyl 2.3 L GAS, 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS, 6 Cyl 4.0 L GAS
View related parts
Ford Ranger Control Module Part Number: 3L5Z-2C219-DA
Product Specifications
- Other Name: Control; ABS Control Module
- Manufacturer Note: ECU, 4X4 - 4 wheel ABS
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2003 Ford Ranger | Edge, XL, XLT | 4 Cyl 2.3 L GAS, 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS, 6 Cyl 4.0 L GAS
View related parts
Ford Ranger Control Module Part Number: 3L5Z-2C219-CA
Product Specifications
- Other Name: Control; ABS Control Module
- Manufacturer Note: ECU, 4X2- 4 wheel ABS
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2003 Ford Ranger | Edge, XL, XLT | 4 Cyl 2.3 L GAS, 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS, 6 Cyl 4.0 L GAS
View related parts
Ford Ranger Control Module Part Number: 1L5Z-2C219-FA
Product Specifications
- Other Name: Control; ABS Control Module
- Manufacturer Note: ECU, 4X4 - 4 wheel ABS
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2001-2002 Ford Ranger | Edge, XL, XLT | 4 Cyl 2.3 L GAS, 4 Cyl 2.5 L GAS, 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS, 6 Cyl 4.0 L GAS
View related parts
Ford Ranger Control Module Part Number: 1L5Z-2C219-EA
Product Specifications
- Other Name: Control; ABS Control Module; Brake Proportioning Valve; Proportioner Valve
- Manufacturer Note: ECU, 4X2 - 4 wheel ABS
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2001-2003 Ford Ranger | Edge, XL, XLT | 4 Cyl 2.3 L GAS, 4 Cyl 2.5 L GAS, 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS, 6 Cyl 4.0 L GAS
View related parts
Ford Ranger Modulator Valve Part Number: BL5Z-2C215-B
Product Specifications
- Other Name: Module; ABS Hydraulic Assembly; ABS Control Module; ABS Control Unit
- Replaces: AL5Z-2C215-B
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2010-2011 Ford Ranger | Sport, XL, XLT | 4 Cyl 2.3 L GAS, 6 Cyl 4.0 L GAS

Ford Ranger ABS Control Module

OEM ABS Control Module boasts unmatched quality. Each part goes through full quality checks. They adhere to Ford's official factory standards. These steps remove flaws and inconsistencies. So you can get ABS Control Module with long life and a perfect fit. Come to our website and find genuine Ford Ranger parts. We keep a wide inventory of OEM Ranger parts at the highly affordable prices. It's easy to search, compare, and pick what you need. You'll love the clear info and simple checkout. We offer top-rated customer service, and we reply fast. We also ship promptly to ensure your order arrives on time.

ABS Control Module in Ford Ranger is among the car's critical part in the anti-lock braking system that aims at preventing wheel locking whenever there is vigorous braking. This function is very vital in controlling the movement of vehicles on the road to overcome the problem of skidding in difficult weather conditions. It works with the help of wheel speed sensors which signalize about lock state and valves and the pump which control the necessary brake pressure for increasing the unit's braking capabilities. Through the years of production, the Ford Ranger models have had different styles of the ABS Control Module integrated in them, improvement of which have led to such aspects like the ESC and traction control. These enhancement enable enhanced correction of the vehicle direction during a skid, as well as better control of brake force during acceleration. Although the ABS Control Module most of the times increases safety and shortened stopping distances, it, however, increases the braking distance on slippery road surfaces.

Ford Ranger ABS Control Module Parts and Q&A

Control Module
4L5Z-2C286-AA
Q: How to Bleed the Brake System After Installing a New ABS Control Module on Ford Ranger?
A:
The process of venting brake fluid from the system occurs through four steps after installing a new Hydraulic Control Unit (HCU) for Four Wheel Anti-Lock Brake System (4WABS). Start by connecting an NGS DCL cable adapter to the vehicle data link connector (DLC) under the dash then proceed with the NGS instructions for fluid bleeding. Proceed to clean the brake master cylinder filler cap before removing it to add brake fluid from the specified brake fluid list. A clear drain tube should be fastened to the RH rear bleeder screw while its other end rests in a brake fluid-filled container. An assistant should pump the brake pedal before maintaining firm pressure on it. To accomplish the RH rear bleeder screw bleeding you must begin with a fluid stream before tightening the screw when the assistant continues pressure on the pedal. Proceed with the bleeding process again without clearing or replacing brake fluid until slides of pure transparent fluid appear from the tap which signals to refill the master cylinder as required. Proceed with bleedings starting from the LH rear bleeder screw followed by the RH front bleeder screw and ending with the LH front bleeder screw. Another complete bleed procedure should be performed on each of the four corners using the standard technique.
Control Module
XL2Z-2C219-BA
Q: How to Service and Repair the Rear ABS Control Module on Ford Ranger?
A:
The service repair for Electronic Brake Control Module Antilock Control needs users to start by stripping the radio along with the center instrument panel finish panel and disconnecting the cigar lighter electrical connectors while removing all bolts. The first step in this procedure requires you to eliminate the instrument panel ash receptacle through bolt removal. Next step is to remove the anti-lock brake control module through bolt removal and deconnecting its electrical connector. The installation procedure should be performed in the opposite order of removal.