How to service and repair the brake caliper on 2004 Ford Mustang?

Start by lifting the vehicle using proper supports before you remove the wheel combined with the tire. Use caution when working with brake fluid since the substance contains polyglycol ethers and polyglycols which should never touch your eyes needing extensive hand washing after exposure. The correct response to eye contact exposure requires running water flush for 15 minutes followed by immediate medical assessment if the eyes show no signs of improvement. Drink water after swallowing the substance then vomit from your mouth before immediately looking for emergency care. Brake fluid poses damage to plastic materials and paints thus immediate water washing becomes crucial when dealing with any fluid leakage. The front brake hose disconnect process starts with removing the front brake flow bolt and hose separation while discarding copper washers followed by hose plugging. Using a caliper holder on the guide pins, navigate to loosen and remove the caliper bolts before lifting up the caliper to inspect for boot damage and leaks which might need further removal of the components. When installing the caliper check that both the anti-rattle spring sits properly as well as the guide pin boots are correctly arranged to avoid equipment damage. You should install the disc brake caliper after keeping the guide pins still then tighten the caliper bolts while using new copper washers. After bleeding the caliper the front brake hose installation ends with reinstalling the wheel with tire assembly. During the final step replace the brake master cylinder reservoir with clean High Performance DOT 3 Brake Fluid C6AZ-19542-AB or an equivalent fluid that meets Ford specification ESA-M6C25-A while installing the filler cap and performing a brake system operation check.

OEM 2004 Ford Mustang Brake Caliper

Caliper

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

13 Brake Calipers found

View related parts
2004 Ford Mustang Caliper, Front Driver Side Part Number: 3R3Z-2B121-BA
Product Specifications
- Other Name: Caliper With Pads; Disc Brake Caliper, Front Left; Brake Caliper Repair Kit; Brake Caliper
- Manufacturer Note: Complete Asy
- Position: Front Driver Side
- Base No.: 2B120
- Item Weight: 10.70 Pounds
- Item Dimensions: 7.5 x 6.2 x 7.7 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 3R3Z-2B121-BA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2004 Ford Mustang Submodels:
- SVT Cobra | 8 Cyl 4.6 L GAS
View related parts
2004 Ford Mustang Caliper, Rear Driver Side Part Number: 3R3Z-2553-AA
Product Specifications
- Other Name: Caliper With Pads; Disc Brake Caliper, Rear Left; Brake Caliper Repair Kit; Brake Caliper
- Manufacturer Note: Warranty Eligible
- Position: Rear Driver Side
- Base No.: 2552A
- Item Weight: 8.20 Pounds
- Item Dimensions: 7.3 x 6.2 x 7.5 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 3R3Z-2553-AA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2004 Ford Mustang Submodels:
- SVT Cobra | 8 Cyl 4.6 L GAS
View related parts
2004 Ford Mustang Caliper, Front Passenger Side Part Number: XR3Z-2B120-AB
Product Specifications
- Other Name: Caliper Assembly - Brake; Disc Brake Caliper, Front Right; Brake Caliper Repair Kit; Brake Caliper
- Position: Front Passenger Side
- Base No.: 2B120
- Item Weight: 5.40 Pounds
- Item Dimensions: 5.2 x 7.4 x 9.2 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: XR3Z-2B120-AB
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2004 Ford Mustang Submodels:
- Base, GT, GT Bullitt | 6 Cyl 3.8 L GAS, 8 Cyl 4.6 L GAS
View related parts
2004 Ford Mustang Caliper, Front Passenger Side Part Number: 3R3Z-2B120-AB
Product Specifications
- Other Name: Caliper With Pads; Disc Brake Caliper, Front Right; Brake Caliper Repair Kit; Brake Caliper
- Manufacturer Note: Complete Asy
- Position: Front Passenger Side
- Base No.: 2B120
- Item Weight: 9.80 Pounds
- Item Dimensions: 7.3 x 6.1 x 7.5 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 3R3Z-2B120-AB
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2004 Ford Mustang Submodels:
- SVT Cobra, SVT Cobra 10th Anniversary | 8 Cyl 4.6 L GAS
View related parts
2004 Ford Mustang Caliper, Front Driver Side Part Number: 3R3Z-2B121-CA
Product Specifications
- Other Name: Caliper With Pads; Disc Brake Caliper, Front Left; Brake Caliper Repair Kit; Brake Caliper
- Manufacturer Note: Complete Asy
- Position: Front Driver Side
- Base No.: 2B120
- Item Weight: 11.50 Pounds
- Item Dimensions: 7.4 x 6.4 x 7.7 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 3R3Z-2B121-CA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2004 Ford Mustang Submodels:
- Base, GT | 6 Cyl 3.8 L GAS, 6 Cyl 3.9 L GAS, 8 Cyl 4.6 L GAS
View related parts
2004 Ford Mustang Caliper, Front Driver Side Part Number: 3R3Z-2B121-AA
Product Specifications
- Other Name: Caliper With Pads; Disc Brake Caliper, Front Left; Brake Caliper Repair Kit; Brake Caliper
- Manufacturer Note: Complete Asy
- Position: Front Driver Side
- Base No.: 2B120
- Item Weight: 10.20 Pounds
- Item Dimensions: 7.6 x 6.3 x 7.5 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 3R3Z-2B121-AA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2004 Ford Mustang Submodels:
- Mach 1 | 8 Cyl 4.6 L GAS
View related parts
2004 Ford Mustang Caliper, Front Passenger Side Part Number: 3R3Z-2B120-CA
Product Specifications
- Other Name: Caliper With Pads; Disc Brake Caliper, Front Right; Brake Caliper Repair Kit; Brake Caliper
- Manufacturer Note: Complete Asy
- Position: Front Passenger Side
- Base No.: 2B120
- Item Weight: 0.70 Pounds
- Item Dimensions: 7.3 x 6.3 x 7.6 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 3R3Z-2B120-CA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2004 Ford Mustang Submodels:
- Base, GT | 6 Cyl 3.8 L GAS, 6 Cyl 3.9 L GAS, 8 Cyl 4.6 L GAS
View related parts
2004 Ford Mustang Caliper, Front Passenger Side Part Number: 3R3Z-2B120-AA
Product Specifications
- Other Name: Caliper With Pads; Disc Brake Caliper, Front Right; Brake Caliper Repair Kit; Brake Caliper
- Manufacturer Note: Complete Asy
- Position: Front Passenger Side
- Base No.: 2B120
- Item Weight: 9.50 Pounds
- Item Dimensions: 5.3 x 6.2 x 8.4 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 3R3Z-2B120-AA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2004 Ford Mustang Submodels:
- Mach 1 | 8 Cyl 4.6 L GAS
View related parts
2004 Ford Mustang Caliper, Rear Driver Side Part Number: 3R3Z-2553-CA
Product Specifications
- Other Name: Caliper Assembly - Brake; Disc Brake Caliper, Rear Left; Brake Caliper Repair Kit; Caliper Assembly - Brake - Less Pads; Brake Caliper
- Position: Rear Driver Side
- Base No.: 2552B
- Item Weight: 8.40 Pounds
- Item Dimensions: 4.4 x 5.6 x 7.0 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 3R3Z-2553-CA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2004 Ford Mustang Submodels:
- Mach 1, SVT Cobra, SVT Cobra 10th Anniversary | 8 Cyl 4.6 L GAS, 8 Cyl 5.0 L GAS
View related parts
2004 Ford Mustang Caliper, Rear Passenger Side Part Number: 3R3Z-2552-CA
Product Specifications
- Other Name: Caliper Assembly - Brake; Disc Brake Caliper, Rear Right; Brake Caliper Repair Kit; Caliper Assembly - Brake - Less Pads; Brake Caliper
- Position: Rear Passenger Side
- Base No.: 2552
- Item Weight: 8.00 Pounds
- Item Dimensions: 9.9 x 7.7 x 5.5 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 3R3Z-2552-CA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2004 Ford Mustang Submodels:
- Mach 1, SVT Cobra, SVT Cobra 10th Anniversary | 8 Cyl 4.6 L GAS, 8 Cyl 5.0 L GAS
View related parts
2004 Ford Mustang Caliper, Passenger Side Part Number: 3R3Z-2552-AA
Product Specifications
- Other Name: Caliper With Pads; Brake Caliper Repair Kit; Brake Caliper
- Manufacturer Note: Warranty Eligible
- Position: Passenger Side
- Base No.: 2552A
- Item Weight: 3.20 Pounds
- Item Dimensions: 7.6 x 6.3 x 7.7 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 3R3Z-2552-AA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2004 Ford Mustang Submodels:
- SVT Cobra | 8 Cyl 4.6 L GAS
View related parts
2004 Ford Mustang Caliper, Rear Driver Side Part Number: 1R3Z-2553-AB
Product Specifications
- Other Name: Caliper Assembly - Brake; Disc Brake Caliper, Rear Left; Brake Caliper Repair Kit; Caliper Assembly - Brake - Less Pads; Brake Caliper
- Manufacturer Note: LH, Exc. Cobra
- Position: Rear Driver Side
- Base No.: 2553
- Item Weight: 7.80 Pounds
- Item Dimensions: 5.0 x 7.5 x 7.5 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 1R3Z-2553-AB
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2004 Ford Mustang Submodels:
- Base, GT, GT Bullitt, GTS | 6 Cyl 3.8 L GAS, 6 Cyl 3.9 L GAS, 8 Cyl 4.6 L GAS, 8 Cyl 5.0 L GAS
View related parts
2004 Ford Mustang Caliper, Rear Passenger Side Part Number: 1R3Z-2552-AB
Product Specifications
- Other Name: Caliper Assembly - Brake; Disc Brake Caliper, Rear Right; Brake Caliper Repair Kit; Caliper Assembly - Brake - Less Pads; Brake Caliper
- Manufacturer Note: RH, exc. Cobra
- Position: Rear Passenger Side
- Base No.: 2552
- Item Weight: 8.10 Pounds
- Item Dimensions: 9.7 x 7.6 x 5.4 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 1R3Z-2552-AB
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2004 Ford Mustang Submodels:
- Base, GT, GT Bullitt, GTS | 6 Cyl 3.8 L GAS, 6 Cyl 3.9 L GAS, 8 Cyl 4.6 L GAS, 8 Cyl 5.0 L GAS

2004 Ford Mustang Brake Caliper

If you're seeking quality and affordability, look no further than our extensive inventory of genuine 2004 Ford Mustang Brake Caliper available at FordPartsDeal.com. You can confidently purchase our OEM 2004 Ford Mustang Brake Caliper as they are supported by the manufacturer's warranty and our hassle-free return policy, alongside the benefit of our fast delivery service.

2004 Ford Mustang Brake Caliper Parts Q&A

Q: How to service and repair the brake caliper on 2004 Ford Mustang?
A: Start by lifting the vehicle using proper supports before you remove the wheel combined with the tire. Use caution when working with brake fluid since the substance contains polyglycol ethers and polyglycols which should never touch your eyes needing extensive hand washing after exposure. The correct response to eye contact exposure requires running water flush for 15 minutes followed by immediate medical assessment if the eyes show no signs of improvement. Drink water after swallowing the substance then vomit from your mouth before immediately looking for emergency care. Brake fluid poses damage to plastic materials and paints thus immediate water washing becomes crucial when dealing with any fluid leakage. The front brake hose disconnect process starts with removing the front brake flow bolt and hose separation while discarding copper washers followed by hose plugging. Using a caliper holder on the guide pins, navigate to loosen and remove the caliper bolts before lifting up the caliper to inspect for boot damage and leaks which might need further removal of the components. When installing the caliper check that both the anti-rattle spring sits properly as well as the guide pin boots are correctly arranged to avoid equipment damage. You should install the disc brake caliper after keeping the guide pins still then tighten the caliper bolts while using new copper washers. After bleeding the caliper the front brake hose installation ends with reinstalling the wheel with tire assembly. During the final step replace the brake master cylinder reservoir with clean High Performance DOT 3 Brake Fluid C6AZ-19542-AB or an equivalent fluid that meets Ford specification ESA-M6C25-A while installing the filler cap and performing a brake system operation check.