How to service the front fender on 2006 Ford Expedition?

The service of the Expedition front fender starts with removing its front fender splash shield. First detach the two bolts holding the front fender to the front bumper cover and secure them at 8 Nm (71 lb-in) when reinstalling. The front fender-to-radiator support bolt needs to be tightened to 12 Nm (9 lb-ft) when installing. The service of the front fender requires you to remove its two lower bolts before reinstalling them at 12 Nm (9 lb-ft). Separate the foam insulator by removing the pin-type retainer as well as both inner bolts that need 12 Nm (9 lb-ft) tightening upon reinstallation. You should first loosen the headlamp retainer bolt then remove the headlamp after discharging electrical connections and removing all its bolts. After removing the two front bolts of the fender you should tighten them to 8 Nm (71 lb-in) during reinstallation. Begin by removing the cowl panel grille and after that detach the front fender while tightening its bolts to 12 Nm (9 lb-ft) when reinstalling. The complete procedure ends with executing the opposite steps from removal.

OEM 2006 Ford Expedition Fender

Wheel Fender

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

4 Fenders found

View related parts
2006 Ford Expedition Fender, Front Driver Side Part Number: 2L1Z-16006-CA
Product Specifications
- Other Name: Fender Assembly - Front; Fender, Front Left
- Position: Front Driver Side
- Base No.: 16005B
- Item Weight: 14.90 Pounds
- Item Dimensions: 59.9 x 40.2 x 12.4 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 2L1Z-16006-CA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2006 Ford Expedition Submodels:
- Eddie Bauer, King Ranch, Limited, NBX, XLS, XLT, XLT Sport | 8 Cyl 4.6 L GAS, 8 Cyl 5.4 L GAS
View related parts
2006 Ford Expedition Fender, Front Driver Side Part Number: 2L1Z-16006-DA
Product Specifications
- Other Name: Fender Assembly - Front; Fender, Front Left
- Manufacturer Note: (CP) Designates Crash Part - When Ordering Please Refer To Crash Part Truckload Program Guidelines
- Position: Front Driver Side
- Base No.: 16005B
- Item Weight: 24.20 Pounds
- Item Dimensions: 57.7 x 40.7 x 11.0 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 2L1Z-16006-DA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2006 Ford Expedition Submodels:
- Eddie Bauer, King Ranch, Limited, NBX, XLS, XLT, XLT Sport | 8 Cyl 4.6 L GAS, 8 Cyl 5.4 L GAS
View related parts
2006 Ford Expedition Fender, Front Passenger Side Part Number: 2L1Z-16005-DA
Product Specifications
- Other Name: Fender Assembly - Front; Fender, Front Right
- Position: Front Passenger Side
- Base No.: 16005A
- Item Weight: 23.60 Pounds
- Item Dimensions: 56.1 x 40.7 x 11.2 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 2L1Z-16005-DA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2006 Ford Expedition Submodels:
- Eddie Bauer, King Ranch, Limited, NBX, XLS, XLT, XLT Sport | 8 Cyl 4.6 L GAS, 8 Cyl 5.4 L GAS
View related parts
2006 Ford Expedition Fender, Front Passenger Side Part Number: 2L1Z-16005-CA
Product Specifications
- Other Name: Fender Assembly - Front; Fender, Front Right
- Position: Front Passenger Side
- Base No.: 16005A
- Item Weight: 22.30 Pounds
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 2L1Z-16005-CA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2006 Ford Expedition Submodels:
- Eddie Bauer, King Ranch, Limited, NBX, XLS, XLT, XLT Sport | 8 Cyl 4.6 L GAS, 8 Cyl 5.4 L GAS

2006 Ford Expedition Fender

If you're seeking quality and affordability, look no further than our extensive inventory of genuine 2006 Ford Expedition Fender available at FordPartsDeal.com. You can confidently purchase our OEM 2006 Ford Expedition Fender as they are supported by the manufacturer's warranty and our hassle-free return policy, alongside the benefit of our fast delivery service.

2006 Ford Expedition Fender Parts Q&A

Q: How to service the front fender on 2006 Ford Expedition?
A: The service of the Expedition front fender starts with removing its front fender splash shield. First detach the two bolts holding the front fender to the front bumper cover and secure them at 8 Nm (71 lb-in) when reinstalling. The front fender-to-radiator support bolt needs to be tightened to 12 Nm (9 lb-ft) when installing. The service of the front fender requires you to remove its two lower bolts before reinstalling them at 12 Nm (9 lb-ft). Separate the foam insulator by removing the pin-type retainer as well as both inner bolts that need 12 Nm (9 lb-ft) tightening upon reinstallation. You should first loosen the headlamp retainer bolt then remove the headlamp after discharging electrical connections and removing all its bolts. After removing the two front bolts of the fender you should tighten them to 8 Nm (71 lb-in) during reinstallation. Begin by removing the cowl panel grille and after that detach the front fender while tightening its bolts to 12 Nm (9 lb-ft) when reinstalling. The complete procedure ends with executing the opposite steps from removal.