How to Service a Rear Two-Piece Drive Shaft on 2007 Lincoln Mark LT?

The service of the rear two-piece driveshaft requires a vehicle set to NEUTRAL position on a hoist. Use index-marks to register the driveshaft flange to pinion flange positioning and driveshaft to extension housing alignment that will help during reinstall. Install new drive flange bolts after detaching the original bolts because their torque should reach 103 Newtons meter (76 foot pounds) following installation. Drive caution because the driveshaft flange tightly fits onto the flange pilot yet make sure to avoid hammering any parts and use a suitable tool that can only be used in the designated area for disconnecting the driveshaft flange. The maintenance starts by loosening the center bearing bolts so you can lower the driveshaft while sliding the slip yoke backward from the output shaft. Once reinstallation happens, fasten these bolts to a torque of 48 Nm (35 ft. lbs.). Fasten the extension housing to stop fluid leakage. To properly reinstall the driveshaft you must verify that both pinion flange pilots fully contact the driveshaft flanges before tightening the bolts in a crosswise pattern. The removal process should be reversed by applying index mark alignment from removal along with Threadlock and Sealer coating on original driveshaft flange bolts when new replacement bolts are unavailable.

OEM 2007 Lincoln Mark LT Drive Shaft

Axle Shaft

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

13 Drive Shafts found

View related parts
2007 Lincoln Mark LT Drive Shaft
Part Number: 5L3Z-4A376-A
$676.20 MSRP: $990.77
You Save: $314.57 (32%)
ADD TO CART
Product Specifications
- Other Name: Shaft Assembly - Drive; Driveshaft
- Replaces: 2L1Z-4A376-AA
- Base No.: 4A376
- Item Weight: 21.00 Pounds
- Item Dimensions: 6.1 x 6.1 x 58.4 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 5L3Z-4A376-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2007 Lincoln Mark LT Submodels:
- Base | 8 Cyl 5.4 L GAS
View related parts
2007 Lincoln Mark LT Drive Shaft
Part Number: 8L3Z-4R602-G
$997.88 MSRP: $1364.62
You Save: $366.74 (27%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft Assembly - Drive; Driveshaft
- Replaces: 5L3Z-4R602-UC, 5L3Z-4R602-U, 7L3Z-4R602-G
- Base No.: 4R602
- Item Weight: 51.80 Pounds
- Item Dimensions: 6.6 x 13.9 x 59.8 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 8L3Z-4R602-G
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2007 Lincoln Mark LT Submodels:
- Base | 8 Cyl 5.4 L GAS
View related parts
2007 Lincoln Mark LT Drive Shaft, Rear
Part Number: 8L3Z-4602-D
$731.25 MSRP: $1000.00
You Save: $268.75 (27%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft Assembly - Drive; Drive Shaft, Rear; Driveshaft
- Position: Rear
- Replaces: 5L3Z-4602-DB, 7L3Z-4602-D
- Base No.: 4602
- Item Weight: 48.30 Pounds
- Item Dimensions: 6.8 x 14.3 x 58.7 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 8L3Z-4602-D
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2007 Lincoln Mark LT Submodels:
- Base | 8 Cyl 5.4 L GAS
View related parts
2007 Lincoln Mark LT Drive Shaft
Part Number: 8L3Z-4R602-F
$635.72 MSRP: $869.35
You Save: $233.63 (27%)
Product Specifications
- Other Name: Shaft Assembly - Drive; Driveshaft
- Replaces: 7L3Z-4R602-F
- Base No.: 4R602
- Item Weight: 50.00 Pounds
- Item Dimensions: 9.8 x 76.8 x 7.5 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 8L3Z-4R602-F
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2007 Lincoln Mark LT Submodels:
- Base | 8 Cyl 5.4 L GAS
View related parts
2007 Lincoln Mark LT Drive Shaft, Rear
Part Number: 8L3Z-4602-K
Product Specifications
- Other Name: Shaft Assembly - Drive; Drive Shaft, Rear; Driveshaft
- Position: Rear
- Replaces: 7L3Z-4602-K, 5L3Z-4602-XC
- Base No.: 4602
- Item Weight: 21.40 Pounds
- Item Dimensions: 9.8 x 13.3 x 54.0 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 8L3Z-4602-K
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2007 Lincoln Mark LT Submodels:
- Base | 8 Cyl 5.4 L GAS
View related parts
2007 Lincoln Mark LT Drive Shaft, Rear
Part Number: 5L3Z-4602-MA
Product Specifications
- Other Name: Shaft Assembly - Drive; Drive Shaft, Rear; Driveshaft
- Position: Rear
- Replaces: 4L3Z-4602-MC
- Base No.: 4602
- Item Weight: 34.00 Pounds
- Item Dimensions: 6.3 x 6.3 x 56.2 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 5L3Z-4602-MA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2007 Lincoln Mark LT Submodels:
- Base | 8 Cyl 5.4 L GAS
View related parts
2007 Lincoln Mark LT Drive Shaft
Part Number: 8L3Z-4R602-D
$747.00 MSRP: $1021.54
You Save: $274.54 (27%)
Product Specifications
- Other Name: Shaft Assembly - Drive; Driveshaft
- Replaces: 5L3Z-4R602-RC, 6L3Z-4R602-G, 7L3Z-4R602-D
- Base No.: 4R602
- Item Weight: 50.40 Pounds
- Item Dimensions: 26.2 x 6.2 x 15.3 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 8L3Z-4R602-D
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2007 Lincoln Mark LT Submodels:
- Base | 8 Cyl 5.4 L GAS
View related parts
2007 Lincoln Mark LT Drive Shaft, Rear
Part Number: 8L3Z-4602-C
Product Specifications
- Other Name: Shaft Assembly - Drive; Drive Shaft, Rear; Driveshaft
- Position: Rear
- Replaces: 4L3Z-4602-CB, 7L3Z-4602-C, 5L3Z-4602-CB
- Base No.: 4602
- Item Weight: 29.70 Pounds
- Item Dimensions: 8.5 x 13.3 x 57.0 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 8L3Z-4602-C
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2007 Lincoln Mark LT Submodels:
- Base | 8 Cyl 5.4 L GAS
View related parts
2007 Lincoln Mark LT Drive Shaft
Part Number: 8L3Z-4R602-H
Product Specifications
- Other Name: Shaft Assembly - Drive; Driveshaft
- Replaces: 5L3Z-4R602-VC, 6L3Z-4R602-K, 7L3Z-4R602-H, 5L3Z-4R602-V, 5L3Z-4R602-VA
- Base No.: 4R602
- Item Weight: 59.10 Pounds
- Item Dimensions: 6.6 x 13.9 x 73.5 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 8L3Z-4R602-H
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2007 Lincoln Mark LT Submodels:
- Base | 8 Cyl 5.4 L GAS
View related parts
2007 Lincoln Mark LT Drive Shaft
Part Number: 8L3Z-4R602-B
Product Specifications
- Other Name: Shaft Assembly - Drive; Driveshaft
- Replaces: 7L3Z-4R602-B
- Base No.: 4R602
- Item Weight: 51.10 Pounds
- Item Dimensions: 6.8 x 14.2 x 61.0 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 8L3Z-4R602-B
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2007 Lincoln Mark LT Submodels:
- Base | 8 Cyl 5.4 L GAS
View related parts
2007 Lincoln Mark LT Drive Shaft, Rear
Part Number: 8L3Z-4602-G
Product Specifications
- Other Name: Shaft Assembly - Drive; Drive Shaft, Rear; Driveshaft
- Position: Rear
- Replaces: 7L3Z-4602-G
- Base No.: 4602
- Item Weight: 25.30 Pounds
- Item Dimensions: 8.9 x 13.3 x 57.6 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 8L3Z-4602-G
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2007 Lincoln Mark LT Submodels:
- Base | 8 Cyl 5.4 L GAS
View related parts
2007 Lincoln Mark LT Drive Shaft
Part Number: 7L3Z-4R602-J
Product Specifications
- Other Name: Shaft Assembly - Drive; Driveshaft
- Replaces: 5L3Z-4R602-WC, 5L3Z-4R602-W, 6L3Z-4R602-W
- Base No.: 4R602
- Item Weight: 54.60 Pounds
- Item Dimensions: 9.5 x 77.5 x 7.5 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 7L3Z-4R602-J
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2007 Lincoln Mark LT Submodels:
- Base | 8 Cyl 5.4 L GAS
View related parts
2007 Lincoln Mark LT Drive Shaft, Rear
Part Number: 5L3Z-4602-NA
Product Specifications
- Other Name: Shaft Assembly - Drive; Drive Shaft, Rear; Driveshaft
- Position: Rear
- Base No.: 4602
- Item Dimensions: 10.1 x 12.7 x 56.7 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 5L3Z-4602-NA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2007 Lincoln Mark LT Submodels:
- Base | 8 Cyl 5.4 L GAS

2007 Lincoln Mark LT Drive Shaft

If you're seeking quality and affordability, look no further than our extensive inventory of genuine 2007 Lincoln Mark LT Drive Shaft available at FordPartsDeal.com. You can confidently purchase our OEM 2007 Lincoln Mark LT Drive Shaft as they are supported by the manufacturer's warranty and our hassle-free return policy, alongside the benefit of our fast delivery service.

2007 Lincoln Mark LT Drive Shaft Parts Questions & Experts Answers

Q: How to Service a Rear Two-Piece Drive Shaft on 2007 Lincoln Mark LT?
A: The service of the rear two-piece driveshaft requires a vehicle set to NEUTRAL position on a hoist. Use index-marks to register the driveshaft flange to pinion flange positioning and driveshaft to extension housing alignment that will help during reinstall. Install new drive flange bolts after detaching the original bolts because their torque should reach 103 Newtons meter (76 foot pounds) following installation. Drive caution because the driveshaft flange tightly fits onto the flange pilot yet make sure to avoid hammering any parts and use a suitable tool that can only be used in the designated area for disconnecting the driveshaft flange. The maintenance starts by loosening the center bearing bolts so you can lower the driveshaft while sliding the slip yoke backward from the output shaft. Once reinstallation happens, fasten these bolts to a torque of 48 Nm (35 ft. lbs.). Fasten the extension housing to stop fluid leakage. To properly reinstall the driveshaft you must verify that both pinion flange pilots fully contact the driveshaft flanges before tightening the bolts in a crosswise pattern. The removal process should be reversed by applying index mark alignment from removal along with Threadlock and Sealer coating on original driveshaft flange bolts when new replacement bolts are unavailable.