How to service the front ABS sensor on 2007 Lincoln Navigator?

Service of the front ABS sensor starts with turning off the air suspension switch if installed and positioning the vehicle for servicing on a hoist using NEUTRAL gear position. Disconnect the ABS sensor electrical connector before removing the ABS sensor harness retainer bolt and removing the retainers. Reinstall these retainers tight at 12 Nm (9 ft. lbs.). When working on the brake hose, prevent the caliper from hanging since damage may occur; first remove the two caliper anchor bolts, then place the caliper and pads with anchor plate aside while securely attaching the caliper with mechanic's wire. Reinstall the caliper anchor bolts at 200 Nm until they reach torque specifications of 148 foot pounds. After removing the brake disc, you should proceed to take off the front ABS sensor bolt followed by the sensor itself before tightening the sensor to 18 Nm (13 ft. lbs.) when reinstallation occurs. The installation process ends by performing the reverse steps of removal.

OEM 2007 Lincoln Navigator ABS Sensor

ABS Wheel Speed Sensor

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

2 ABS Sensors found

View related parts
2007 Lincoln Navigator ABS Sensor, Rear Driver Side
Part Number: 7L1Z-2C190-E
$89.04 MSRP: $146.51
You Save: $57.47 (40%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Sensor Assembly; ABS Wheel Speed Sensor, Rear, Rear Left, Rear Right; Rear Speed Sensor
- Position: Rear Driver Side
- Replaces: 7L1Z-2C190-D, 7L1Z-2C204-D
- Base No.: 2C190
- Item Weight: 0.80 Pounds
- Item Dimensions: 7.5 x 2.6 x 7.5 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 7L1Z-2C190-E
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2007 Lincoln Navigator Submodels:
- Base, L, L Luxury, L Ultimate, Luxury, Ultimate | 8 Cyl 5.4 L FLEX, 8 Cyl 5.4 L GAS
View related parts
2007 Lincoln Navigator ABS Sensor, Front Passenger Side
Part Number: 7L1Z-2C204-F
$76.75 MSRP: $126.29
You Save: $49.54 (40%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Sensor Assembly; ABS Wheel Speed Sensor, Front Left, Front Right; ABS Wheel Speed Sensor; Front Speed Sensor
- Position: Front Passenger Side
- Replaces: 7L1Z-2C204-B
- Base No.: 2C204
- Item Weight: 0.70 Pounds
- Item Dimensions: 7.6 x 2.6 x 7.3 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 7L1Z-2C204-F
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2007 Lincoln Navigator Submodels:
- Base, L, L Luxury, L Ultimate, Luxury, Ultimate | 8 Cyl 5.4 L FLEX, 8 Cyl 5.4 L GAS

2007 Lincoln Navigator ABS Sensor

If you're seeking quality and affordability, look no further than our extensive inventory of genuine 2007 Lincoln Navigator ABS Sensor available at FordPartsDeal.com. You can confidently purchase our OEM 2007 Lincoln Navigator ABS Sensor as they are supported by the manufacturer's warranty and our hassle-free return policy, alongside the benefit of our fast delivery service.

2007 Lincoln Navigator ABS Sensor Parts Questions & Experts Answers

Q: How to service the front ABS sensor on 2007 Lincoln Navigator?
A: Service of the front ABS sensor starts with turning off the air suspension switch if installed and positioning the vehicle for servicing on a hoist using NEUTRAL gear position. Disconnect the ABS sensor electrical connector before removing the ABS sensor harness retainer bolt and removing the retainers. Reinstall these retainers tight at 12 Nm (9 ft. lbs.). When working on the brake hose, prevent the caliper from hanging since damage may occur; first remove the two caliper anchor bolts, then place the caliper and pads with anchor plate aside while securely attaching the caliper with mechanic's wire. Reinstall the caliper anchor bolts at 200 Nm until they reach torque specifications of 148 foot pounds. After removing the brake disc, you should proceed to take off the front ABS sensor bolt followed by the sensor itself before tightening the sensor to 18 Nm (13 ft. lbs.) when reinstallation occurs. The installation process ends by performing the reverse steps of removal.