How to service and repair the axle shaft assembly on 2009 Ford Escape?

You should start axle shaft assembly servicing by first placing the vehicle in neutral mode while hoisting it into place. First, remove the tire and wheel from the vehicle before you discard the wheel hub nut. Begin service by taking out the bolt which secures a speed sensor part and set the sensor unit to the side. Lower down the ball joint bolt and nut before throwing them into waste disposal. Maintain the ball joint stud away from contacting the CV joint boot when you disconnect the lower arm from the front wheel knuckle. The front hub remover should be used to disconnect the axle shaft from its position on the wheel hub. The axle shaft remover and slide hammer should be used to pull the left axle shaft out from the differential area. A brass drift will help strike the right axle shaft at the designated location to extract it. The left axle shaft installation requires alignment of its splines with differential side gear splines followed by pushing it into position until the bearing retainer circlip snaps into place. The installation procedure involves inserting the right axle shaft into the intermediate shaft splines then feeding it until the circlip creates a firm connection between the shafts while applying specified grease on the splines. Position the front wheel hub into the axle shaft installer before inserting the axle shaft followed by fitting in the lower arm to the front wheel knuckle. Fasten the new lower ball joint bolt with its nut by applying 63 Nm (46 lb-ft) torque. Fasten the ABS wheel speed sensor by torquing its bolt to 9 Nm (80 lb-in). Statements show it is vital to avoid nut tightening on the front wheel hub when the vehicle rests on the ground since this action damages wheel bearings; users should first place new front wheel hub nuts before applying brakes to stop axle shaft rotation during tightening to 300 Nm (222 lb-ft). The last step involves installation of front tires and wheels followed by checking and filling the transaxle fluid when needed.

OEM 2009 Ford Escape Axle Shaft

Car Axle Shaft

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

12 Axle Shafts found

View related parts
2009 Ford Escape Axle Assembly, Front Driver Side Part Number: 9L8Z-3A427-D
$128.18 MSRP: $210.91
You Save: $82.73 (40%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft - Front Axle; CV Axle Assembly, Front Left; GSP CV Axle; Axle Shaft; CV Axle Assembly
- Position: Front Driver Side
- Replaces: 9L8Z-3A427-C, 9L8Z-3A427-A, 9L8Z-3A427-B
- Base No.: 3B436
- Item Weight: 15.40 Pounds
- Item Dimensions: 34.3 x 5.0 x 4.9 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 9L8Z-3A427-D
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2009 Ford Escape Submodels:
- Limited, XLS, XLT | 4 Cyl 2.5 L GAS, 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS
View related parts
2009 Ford Escape Intermediate Shaft, Front Part Number: 9L8Z-3A329-A
$262.19 MSRP: $385.00
You Save: $122.81 (32%)
ADD TO CART
Product Specifications
- Other Name: Shaft; CV Intermediate Shaft, Front; Intermed Shaft; CV Intermediate Shaft
- Position: Front
- Base No.: 3B414A
- Item Weight: 8.60 Pounds
- Item Dimensions: 5.0 x 5.1 x 22.3 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 9L8Z-3A329-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2009 Ford Escape Submodels:
- Limited, XLS, XLT | 4 Cyl 2.5 L GAS, 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS
View related parts
2009 Ford Escape Intermediate Shaft Part Number: 9L8Z-3A329-B
$249.70 MSRP: $366.67
You Save: $116.97 (32%)
ADD TO CART
Product Specifications
- Other Name: Shaft; CV Intermediate Shaft; Intermed Shaft
- Base No.: 3B414A
- Item Weight: 6.50 Pounds
- Item Dimensions: 21.2 x 6.2 x 4.1 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 9L8Z-3A329-B
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2009 Ford Escape Submodels:
- Limited, XLS, XLT | 4 Cyl 2.5 L GAS, 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS
View related parts
2009 Ford Escape Axle Assembly, Front Passenger Side Part Number: 5L8Z-3A428-DB
$107.29 MSRP: $173.09
You Save: $65.80 (39%)
ADD TO CART
Product Specifications
- Other Name: Shaft - Front Axle; CV Axle Assembly, Front Left, Front Right; GSP CV Axle; Axle Shaft; CV Axle Assembly
- Position: Front Passenger Side
- Replaces: 5L8Z-3A428-DA, YL8Z-3A428-CA, YL8Z-3A428-DA, TX-318
- Base No.: 3B436
- Item Weight: 14.20 Pounds
- Item Dimensions: 28.0 x 4.8 x 4.8 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 5L8Z-3A428-DB
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2009 Ford Escape Submodels:
- Hybrid, Limited, Limited Hybrid, XLS, XLT, XLT No Boundaries, XLT Sport | 4 Cyl 2.0 L GAS, 4 Cyl 2.3 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.3 L GAS, 4 Cyl 2.5 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.5 L GAS, 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS
View related parts
2009 Ford Escape Axle Assembly, Front Driver Side Part Number: 5M6Z-3A427-AB
$106.30 MSRP: $174.91
You Save: $68.61 (40%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft - Front Axle; CV Axle Assembly, Front Left; GSP CV Axle; Axle Shaft; CV Axle Assembly
- Position: Front Driver Side
- Replaces: 5M6Z-3A427-AA
- Base No.: 3B436
- Item Weight: 14.20 Pounds
- Item Dimensions: 27.2 x 4.8 x 4.7 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 5M6Z-3A427-AB
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2009 Ford Escape Submodels:
- Hybrid, Limited Hybrid | 4 Cyl 2.3 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.5 L FULL HYBRID EV-GAS (FHEV)
View related parts
2009 Ford Escape Axle Shafts, Rear Driver Side Part Number: 8L8Z-4K139-A
$279.75 MSRP: $383.83
You Save: $104.08 (28%)
ADD TO CART
Product Specifications
- Other Name: Shaft Assembly - Rear Axle; CV Axle Assembly, Rear Left; GSP CV Axle; Axle Shaft; Axle Assembly; CV Axle Assembly
- Manufacturer Note: Includes ABS Tone Ring Not Serviced Separately
- Position: Rear Driver Side
- Base No.: 4K138
- Item Weight: 17.30 Pounds
- Item Dimensions: 29.8 x 5.2 x 5.1 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 8L8Z-4K139-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2009 Ford Escape Submodels:
- Hybrid, Limited, Limited Hybrid, XLS, XLT | 4 Cyl 2.3 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.3 L GAS, 4 Cyl 2.5 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.5 L GAS, 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS
View related parts
2009 Ford Escape Intermediate Shaft, Front Part Number: 6L8Z-3A329-E
$110.57 MSRP: $152.93
You Save: $42.36 (28%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft; CV Intermediate Shaft, Front; Intermed Shaft
- Position: Front
- Replaces: 6L8Z-3A329-C, 5L8Z-3A329-FA
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 6L8Z-3A329-E
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2009 Ford Escape Submodels:
- Hybrid, Limited, XLS, XLT, XLT No Boundaries | 4 Cyl 2.3 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.3 L GAS, 4 Cyl 2.5 L GAS, 6 Cyl 3.0 L GAS
View related parts
2009 Ford Escape Axle Shafts, Rear Passenger Side Part Number: 8L8Z-4K138-A
$258.64 MSRP: $357.80
You Save: $99.16 (28%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft Assembly; CV Axle Assembly, Rear Right; GSP CV Axle; Axle Shaft; Axle Assembly; CV Axle Assembly
- Manufacturer Note: Includes ABS Tone Ring Not Serviced Separately
- Position: Rear Passenger Side
- Base No.: 4K138
- Item Weight: 16.70 Pounds
- Item Dimensions: 31.3 x 5.1 x 5.1 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 8L8Z-4K138-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2009 Ford Escape Submodels:
- Hybrid, Limited, Limited Hybrid, XLS, XLT | 4 Cyl 2.3 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.3 L GAS, 4 Cyl 2.5 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.5 L GAS, 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS
View related parts
2009 Ford Escape Intermediate Shaft, Front Part Number: AM6Z-3A329-A
$303.39 MSRP: $445.50
You Save: $142.11 (32%)
Product Specifications
- Other Name: Shaft; CV Intermediate Shaft, Front; Axle Shaft; Inner Shaft; CV Intermediate Shaft
- Position: Front
- Replaces: 5M6Z-3A329-A, 5M6Z-3A329-B
- Base No.: 3B414
- Item Weight: 8.10 Pounds
- Item Dimensions: 5.1 x 5.0 x 22.3 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: AM6Z-3A329-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2009 Ford Escape Submodels:
- Hybrid, Limited Hybrid | 4 Cyl 2.3 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.5 L FULL HYBRID EV-GAS (FHEV)
View related parts
2009 Ford Escape Intermediate Shaft, Front Part Number: 9L8Z-3A329-D
Product Specifications
- Other Name: Shaft; CV Intermediate Shaft, Front; Intermed Shaft
- Position: Front
- Replaces: 9L8Z-3A329-C
- Base No.: 3B414
- Item Weight: 8.30 Pounds
- Item Dimensions: 28.2 x 4.9 x 7.2 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 9L8Z-3A329-D
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2009 Ford Escape Submodels:
- Limited, XLS, XLT | 4 Cyl 2.5 L GAS, 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS
View related parts
2009 Ford Escape Intermediate Shaft Part Number: 6M6Z-3A329-B
Product Specifications
- Other Name: Shaft; CV Intermediate Shaft; Axle Shaft; Inner Shaft
- Replaces: 6M6Z-3A329-A
- Base No.: 3B414
- Item Weight: 7.70 Pounds
- Item Dimensions: 4.9 x 5.1 x 21.7 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 6M6Z-3A329-B
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2009 Ford Escape Submodels:
- Hybrid, Limited Hybrid | 4 Cyl 2.3 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.5 L FULL HYBRID EV-GAS (FHEV)
View related parts
2009 Ford Escape Axle Assembly, Front Driver Side Part Number: 6L8Z-3A427-C
Product Specifications
- Other Name: Shaft - Front Axle; CV Axle Assembly, Front Left; GSP CV Axle; Axle Shaft; CV Axle Assembly
- Position: Front Driver Side
- Replaces: 6L8Z-3A427-A, 5L8Z-3A427-BB, YL8Z-3A427-AA
- Base No.: 3B436A
- Item Weight: 16.70 Pounds
- Item Dimensions: 33.9 x 5.1 x 4.9 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 6L8Z-3A427-C
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2009 Ford Escape Submodels:
- Hybrid, Limited, XLS, XLT, XLT No Boundaries | 4 Cyl 2.3 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.3 L GAS, 4 Cyl 2.5 L GAS, 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS

2009 Ford Escape Axle Shaft

If you're seeking quality and affordability, look no further than our extensive inventory of genuine 2009 Ford Escape Axle Shaft available at FordPartsDeal.com. You can confidently purchase our OEM 2009 Ford Escape Axle Shaft as they are supported by the manufacturer's warranty and our hassle-free return policy, alongside the benefit of our fast delivery service.

2009 Ford Escape Axle Shaft Parts Q&A

Q: How to service and repair the axle shaft assembly on 2009 Ford Escape?
A: You should start axle shaft assembly servicing by first placing the vehicle in neutral mode while hoisting it into place. First, remove the tire and wheel from the vehicle before you discard the wheel hub nut. Begin service by taking out the bolt which secures a speed sensor part and set the sensor unit to the side. Lower down the ball joint bolt and nut before throwing them into waste disposal. Maintain the ball joint stud away from contacting the CV joint boot when you disconnect the lower arm from the front wheel knuckle. The front hub remover should be used to disconnect the axle shaft from its position on the wheel hub. The axle shaft remover and slide hammer should be used to pull the left axle shaft out from the differential area. A brass drift will help strike the right axle shaft at the designated location to extract it. The left axle shaft installation requires alignment of its splines with differential side gear splines followed by pushing it into position until the bearing retainer circlip snaps into place. The installation procedure involves inserting the right axle shaft into the intermediate shaft splines then feeding it until the circlip creates a firm connection between the shafts while applying specified grease on the splines. Position the front wheel hub into the axle shaft installer before inserting the axle shaft followed by fitting in the lower arm to the front wheel knuckle. Fasten the new lower ball joint bolt with its nut by applying 63 Nm (46 lb-ft) torque. Fasten the ABS wheel speed sensor by torquing its bolt to 9 Nm (80 lb-in). Statements show it is vital to avoid nut tightening on the front wheel hub when the vehicle rests on the ground since this action damages wheel bearings; users should first place new front wheel hub nuts before applying brakes to stop axle shaft rotation during tightening to 300 Nm (222 lb-ft). The last step involves installation of front tires and wheels followed by checking and filling the transaxle fluid when needed.