How to remove and replace the left-hand engine mount on Ford Crown Victoria?

Proceeding with left-hand engine mount service you should perform ventilation procedures on the fire suppression system to reduce risks of serious injury. Place the vehicle at neutral gear before setting it on the hoist. The work starts by taking out the generator followed by attaching the Engine Lifting Bracket and the Engine Support Bar. Proceed by removing the oil filter then discard it while performing oil lubrication on the O-ring seal of the new filter with fresh engine oil before installation. Secure both left-hand and right-hand lower engine mount nuts with 90 Nm (66 lb-ft) torque before reinstalling them. Raising the engine using the Engine Support Bar allows you to remove the three bolts on the left-hand engine mount before torquing these bolts to 70 Nm (52 lb-ft) upon reinstallation. Repower the vehicle with its fire suppression system by following the safety and operating procedures exactly as directed to ensure proper functionality.

How to service and repair the LH engine mount on Ford Crown Victoria?

The service of LH engine mount begins with extracting the oil level indicator tube from its mount position. Begin by supporting the engine properly then remove the three bolts which attach the mount. Install the new engine mount by following the opposite steps after you remove the bolts during the initial process.

OEM Ford Crown Victoria Engine Mount

Engine Motor Mount

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

8 Engine Mounts found

View related parts
Ford Crown Victoria Transmission Mount Part Number: F8VZ-6068-AA
$127.15 MSRP: $175.90
You Save: $48.75 (28%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Insulator Assembly - Engine Support; Engine Mount Bracket; Transfer Case Mount; Motor Mount; Rear Mount
- Replaces: F4VY-6068-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1998-2002 Ford Crown Victoria | Base, LWB, LX, Police Interceptor, S | 8 Cyl 4.6 L CNG, 8 Cyl 4.6 L GAS
View related parts
Ford Crown Victoria Transmission Mount, Rear Part Number: 3W1Z-6068-BA
$43.01 MSRP: $61.53
You Save: $18.52 (31%)
ADD TO CART
Product Specifications
- Other Name: Insulator Assembly - Engine Support; Auto Trans Mount, Rear; Engine Mount Bracket; Transfer Case Mount; Motor Mount; Rear Mount
- Manufacturer Note: Insulator & retainer, rear engine support
- Position: Rear
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2003-2011 Ford Crown Victoria | Base, Fleet, LWB, LX, LX Sport, Police Interceptor, S, Special Edition | 8 Cyl 4.6 L CNG, 8 Cyl 4.6 L FLEX, 8 Cyl 4.6 L GAS
View related parts
Ford Crown Victoria Front Mount, Passenger Side Part Number: 3W1Z-6038-BB
$76.00 MSRP: $94.00
You Save: $18.00 (20%)
ADD TO CART
Product Specifications
- Other Name: Insulator Assembly; Engine Mount, Front Right, Right; Engine Mount Bracket; Motor Mount; Mount
- Manufacturer Note: RH, front, police, taxi, fleet, limo - severe duty
- Position: Front Passenger Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2003-2011 Ford Crown Victoria | Base, LWB, LX, Police Interceptor | 8 Cyl 4.6 L CNG, 8 Cyl 4.6 L FLEX, 8 Cyl 4.6 L GAS
View related parts
Ford Crown Victoria Front Mount, Driver Side Part Number: 3W1Z-6038-BA
$67.78 MSRP: $98.67
You Save: $30.89 (32%)
ADD TO CART
Product Specifications
- Other Name: Insulator Assembly - Engine Support; Engine Mount, Front Left, Left; Engine Mount Bracket; Motor Mount; Mount
- Manufacturer Note: LH, FRONT
- Position: Driver Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2003-2011 Ford Crown Victoria | Base, Fleet, LWB, LX, LX Sport, Police Interceptor, S, Special Edition | 8 Cyl 4.6 L CNG, 8 Cyl 4.6 L FLEX, 8 Cyl 4.6 L GAS
View related parts
Ford Crown Victoria Front Mount, Passenger Side Part Number: F4AZ-6038-A
$53.33 MSRP: $73.78
You Save: $20.45 (28%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Insulator Assembly; Engine Mount Bracket; Motor Mount; Mount
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1992-1997 Ford Crown Victoria | Base, LX, Police Interceptor, S, Touring Sedan | 8 Cyl 4.6 L CNG, 8 Cyl 4.6 L GAS
View related parts
Ford Crown Victoria Front Mount, Driver Side Part Number: 1W7Z-6038-BA
$54.78 MSRP: $75.78
You Save: $21.00 (28%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Insulator Assembly - Engine Support; Engine Mount Bracket; Engine Mount; Motor Mount; Mount
- Manufacturer Note: LH, with shield
- Position: Driver Side
- Replaces: F8VZ-6038-AA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1998-2002 Ford Crown Victoria | Base, LWB, LX, Police Interceptor, S | 8 Cyl 4.6 L CNG, 8 Cyl 4.6 L GAS
View related parts
Ford Crown Victoria Front Mount, Passenger Side Part Number: 3W7Z-6038-AA
$63.01 MSRP: $96.83
You Save: $33.82 (35%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Insulator Assembly; Engine Mount, Right; Engine Mount Bracket; Motor Mount; Mount
- Manufacturer Note: RH, front, same as 3W1Z-6038-BB but without the heat shield, for lighter duty., not for police, taxi, limo or fleet.
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2003-2011 Ford Crown Victoria | Base, LWB, LX, LX Sport, Police Interceptor, S, Special Edition | 8 Cyl 4.6 L CNG, 8 Cyl 4.6 L FLEX, 8 Cyl 4.6 L GAS
View related parts
Ford Crown Victoria Front Mount, Driver Side Part Number: F4AZ-6038-B
Product Specifications
- Other Name: Insulator Assembly - Engine Support; Engine Mount Bracket; Engine Mount; Motor Mount; Mount
- Position: Driver Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1992-1997 Ford Crown Victoria | Base, LX, Police Interceptor, S, Touring Sedan | 8 Cyl 4.6 L CNG, 8 Cyl 4.6 L GAS

Ford Crown Victoria Engine Mount

OEM Engine Mount boasts unmatched quality. Each part goes through full quality checks. They adhere to Ford's official factory standards. These steps remove flaws and inconsistencies. So you can get Engine Mount with long life and a perfect fit. Come to our website and find genuine Ford Crown Victoria parts. We keep a wide inventory of OEM Crown Victoria parts at the highly affordable prices. It's easy to search, compare, and pick what you need. You'll love the clear info and simple checkout. We offer top-rated customer service, and we reply fast. We also ship promptly to ensure your order arrives on time.

Ford Crown Victoria Engine Mount Parts and Q&A

Front Mount, Driver Side
3W1Z-6038-BA
Q: How to remove and replace the left-hand engine mount on Ford Crown Victoria?
A:
Proceeding with left-hand engine mount service you should perform ventilation procedures on the fire suppression system to reduce risks of serious injury. Place the vehicle at neutral gear before setting it on the hoist. The work starts by taking out the generator followed by attaching the Engine Lifting Bracket and the Engine Support Bar. Proceed by removing the oil filter then discard it while performing oil lubrication on the O-ring seal of the new filter with fresh engine oil before installation. Secure both left-hand and right-hand lower engine mount nuts with 90 Nm (66 lb-ft) torque before reinstalling them. Raising the engine using the Engine Support Bar allows you to remove the three bolts on the left-hand engine mount before torquing these bolts to 70 Nm (52 lb-ft) upon reinstallation. Repower the vehicle with its fire suppression system by following the safety and operating procedures exactly as directed to ensure proper functionality.
Transmission Mount
F8VZ-6068-AA
Q: How to service and repair the LH engine mount on Ford Crown Victoria?
A:
The service of LH engine mount begins with extracting the oil level indicator tube from its mount position. Begin by supporting the engine properly then remove the three bolts which attach the mount. Install the new engine mount by following the opposite steps after you remove the bolts during the initial process.