How Can You Safely Service and Repair a Fuel Level Sensor on Ford Edge?

Safety requires that fuel level sensor service must avoid all activities which produce open flames or burning tobacco objects or smoking near the components since fuel mixtures remain highly flammable and can result in life-threatening injuries. All personal electronic equipment needs storage during this procedure. Handle all fuel carefully while being ready to address possible spills that can catch fire from hot vehicle elements. Start the process by cutting power to the ground cable. To access the fuel tank you should turn the cap clockwise one-fourth turn and then place it safely in a location. Insert a semi-rigid fuel drain tube of 120 inches into the fuel tank filler pipe until the tube reaches the fuel tank position. Before starting drain 3 gallons of fuel to safely lower the fuel tank liquid below where the sensor mounting flange is positioned. First remove all bolts holding the fuel level sensor access cover along with the rear seat. First clean the fuel level sensor connective area and its surrounding region before removing the electric connector. Use absorbent pads to place in your working area for any fuel spills prevention. After releasing the lock tab the fuel level sensor should be rotated counterclockwise for one-fourth of a turn and then lifted out. Check the fuel level sensor flange mating surfaces but do not adjust or polish the area that touches the fuel tank O-ring seal. A new fuel level sensor or fuel tank must be installed when the O-ring contact area shows bent or scratched or corroded condition. The installation process requires the O-ring seal to receive a treatment of clean engine oil. The installation requires users to apply strong pressure on the fuel level sensor while rotating it clockwise until the lock arrow matches the tank notch at less than 15 Nm (133 lb-in) of torque. Complete the installation by following the reverse steps of removal.

OEM Ford Edge Fuel Level Sensor

Gas Gauge Sensor

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

17 Fuel Level Sensors found

View related parts
Ford Edge Fuel Pump, Driver Side
Part Number: F2GZ-9H307-S
$414.28 MSRP: $663.64
You Save: $249.36 (38%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Sender And Pump Assembly; Fuel Pump and Sender Assembly, Left; Fuel Pump Module Assembly
- Position: Driver Side
- Replaces: F2GZ-9H307-J, PFS-1076
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2015-2024 Ford Edge | Sport, ST | 6 Cyl 2.7 L GAS
View related parts
Ford Edge Fuel Pump
Part Number: FT4Z-9350-B
$299.64 MSRP: $440.00
You Save: $140.36 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Pump Assembly - Fuel; Direct Injection High Pressure Fuel Pump
- Replaces: FT4Z-9350-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2015-2018 Ford Edge | Sport | 6 Cyl 2.7 L GAS
View related parts
Ford Edge Fuel Gauge Sending Unit
Part Number: 7T4Z-9A299-B
$37.20 MSRP: $51.46
You Save: $14.26 (28%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Sender Assembly - Fuel Tank; Fuel Sender and Hanger Assembly; Fuel Level Sensor; Fuel Sending Unit; Fuel Sender Unit
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2007-2010 Ford Edge | Limited, SE, SEL, SEL Plus, Sport | 6 Cyl 3.5 L GAS
View related parts
Ford Edge Fuel Gauge Sending Unit, Passenger Side
Part Number: F2GZ-9A299-B
$109.83 MSRP: $174.40
You Save: $64.57 (38%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Sender Assembly - Fuel Tank; Right Fuel Sender and Hanger; Fuel Transfer Unit; Level Sensor.; Fuel Sender Unit
- Manufacturer Note: Sender For 9275 Fuel Pump
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2015-2024 Ford Edge | SE, SEL, Sport, ST, ST-Line, Titanium | 4 Cyl 2.0 L GAS, 6 Cyl 2.7 L GAS, 6 Cyl 3.5 L GAS
View related parts
Ford Edge Fuel Gauge Sending Unit, Driver Side
Part Number: F2GZ-9A299-A
$132.25 MSRP: $210.00
You Save: $77.75 (38%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Sender Assembly - Fuel Tank; Fuel Sender and Hanger Assembly, Left; Fuel Level Sensor; Fuel Sending Unit; Fuel Sender Unit
- Manufacturer Note: Sender For 9H307 Fuel Pump
- Position: Driver Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2015-2024 Ford Edge | SE, SEL, Sport, ST, ST-Line, Titanium | 4 Cyl 2.0 L GAS, 6 Cyl 2.7 L GAS, 6 Cyl 3.5 L GAS
View related parts
Ford Edge Fuel Pump
Part Number: K2GZ-9H307-B
$477.84 MSRP: $765.45
You Save: $287.61 (38%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Sender And Pump Assembly
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2018-2021 Ford Edge | SE, SEL, ST-Line, Titanium | 4 Cyl 2.0 L GAS
View related parts
Ford Edge Fuel Pump, Driver Side
Part Number: K2GZ-9H307-A
$498.71 MSRP: $806.00
You Save: $307.29 (39%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Sender And Pump Assembly; Fuel Pump and Sender Assembly, Left
- Position: Driver Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2019-2024 Ford Edge | SE, SEL, ST-Line, Titanium | 4 Cyl 2.0 L GAS
View related parts
Ford Edge Fuel Gauge Sending Unit, Driver Side
Part Number: F2GZ-9A299-D
$122.52 MSRP: $194.55
You Save: $72.03 (38%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Sender Assembly - Fuel Tank; Fuel Pump Module Assembly; Fuel Level Sensor; Fuel Sending Unit; Fuel Pump Module; Fuel Sender Unit
- Manufacturer Note: Sender For 9H307 Fuel Pump
- Position: Driver Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2015-2018 Ford Edge | SE, SEL, Titanium | 6 Cyl 3.5 L GAS
View related parts
Ford Edge Fuel Gauge Sending Unit, Driver Side
Part Number: F2GZ-9A299-C
$118.30 MSRP: $198.60
You Save: $80.30 (41%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Sender Assembly - Fuel Tank; Fuel Sender and Hanger Assembly, Left; Fuel Level Sensor; Fuel Sending Unit; Fuel Sender Unit
- Manufacturer Note: Sender For 9H307 Fuel Pump
- Position: Driver Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2015-2021 Ford Edge | SE, SEL, Sport, ST, ST-Line, Titanium | 4 Cyl 2.0 L GAS, 6 Cyl 2.7 L GAS, 6 Cyl 3.5 L GAS
View related parts
Ford Edge Fuel Pump, Passenger Side
Part Number: F2GZ-9275-B
$243.46 MSRP: $390.00
You Save: $146.54 (38%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Sender Assembly - Fuel Tank; Fuel Transfer Unit
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2015-2018 Ford Edge | SE, SEL, Titanium | 6 Cyl 3.5 L GAS
View related parts
Ford Edge Fuel Pump, Passenger Side
Part Number: F2GZ-9275-A
$227.23 MSRP: $364.00
You Save: $136.77 (38%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Sender Assembly - Fuel Tank; Right Fuel Pump and Sender; Fuel Transfer Unit.
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2015-2024 Ford Edge | SE, SEL, Sport, ST, ST-Line, Titanium | 4 Cyl 2.0 L GAS, 6 Cyl 2.7 L GAS
View related parts
Ford Edge Fuel Gauge Sending Unit
Part Number: DT4Z-9A299-A
$68.45 MSRP: $114.91
You Save: $46.46 (41%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Sender Assembly - Fuel Tank; Fuel Sender and Hanger; Fuel Pump Module; Fuel Level Sensor; Sending Unit.; Fuel Sender Unit
- Replaces: BT4Z-9A299-B, PS-426
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2011-2014 Ford Edge | Limited, SE, SEL, Sport | 6 Cyl 3.5 L GAS, 6 Cyl 3.7 L GAS
View related parts
Ford Edge Fuel Gauge Sending Unit
Part Number: BT4Z-9A299-A
$52.93 MSRP: $87.09
You Save: $34.16 (40%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Sender Assembly - Fuel Tank; Fuel Sender and Hanger; Fuel Pump Module; Fuel Level Sensor; Sending Unit.; Sending Unit
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2011-2014 Ford Edge | Limited, SE, SEL, Sport | 4 Cyl 2.0 L GAS, 6 Cyl 3.5 L GAS, 6 Cyl 3.7 L GAS
View related parts
Ford Edge Fuel Pump
Part Number: BT4Z-9275-A
$84.75 MSRP: $139.45
You Save: $54.70 (40%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Sender Assembly - Fuel Tank; Fuel Sender and Hanger; Fuel Level Sensor; Sending Unit; Fuel Sender Unit; Sender Assembly
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2011-2014 Ford Edge | Limited, SE, SEL, Sport | 4 Cyl 2.0 L GAS, 6 Cyl 3.5 L GAS, 6 Cyl 3.7 L GAS
View related parts
Ford Edge Fuel Pump
Part Number: 7T4Z-9275-B
$59.67 MSRP: $98.18
You Save: $38.51 (40%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Sender Assembly - Fuel Tank; Fuel Transfer Unit
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2007-2010 Ford Edge | Limited, SE, SEL, SEL Plus, Sport | 6 Cyl 3.5 L GAS
View related parts
Ford Edge Fuel Gauge Sending Unit
Part Number: CT4Z-9A299-B
$96.06 MSRP: $161.27
You Save: $65.21 (41%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Sender Assembly - Fuel Tank; Fuel Sender and Hanger Assembly; Fuel Level Sensor; Fuel Sending Unit; Fuel Sender Unit
- Replaces: CT4Z-9A299-A, PS-432
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2012-2014 Ford Edge | Limited, SE, SEL | 4 Cyl 2.0 L GAS
View related parts
Ford Edge Fuel Gauge Sending Unit
Part Number: 7T4Z-9A299-A
Product Specifications
- Other Name: Sender Assembly - Fuel Tank; Fuel Sender and Hanger Assembly; Fuel Level Sensor; Fuel Sending Unit; Fuel Sender Unit
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2007-2010 Ford Edge | Limited, SE, SEL, SEL Plus, Sport | 6 Cyl 3.5 L GAS

Ford Edge Fuel Level Sensor

Welcome to our website where you can discover high-quality, genuine Ford Edge Fuel Level Sensor. We offer an extensive inventory of OEM Ford Edge Fuel Level Sensor at affordable prices. We are committed to providing top-rated customer service along with prompt delivery.

Ford Edge Fuel Level Sensor Parts Questions & Experts Answers

Fuel Pump
7T4Z-9275-B
Q: How Can You Safely Service and Repair a Fuel Level Sensor on Ford Edge?
A: Safety requires that fuel level sensor service must avoid all activities which produce open flames or burning tobacco objects or smoking near the components since fuel mixtures remain highly flammable and can result in life-threatening injuries. All personal electronic equipment needs storage during this procedure. Handle all fuel carefully while being ready to address possible spills that can catch fire from hot vehicle elements. Start the process by cutting power to the ground cable. To access the fuel tank you should turn the cap clockwise one-fourth turn and then place it safely in a location. Insert a semi-rigid fuel drain tube of 120 inches into the fuel tank filler pipe until the tube reaches the fuel tank position. Before starting drain 3 gallons of fuel to safely lower the fuel tank liquid below where the sensor mounting flange is positioned. First remove all bolts holding the fuel level sensor access cover along with the rear seat. First clean the fuel level sensor connective area and its surrounding region before removing the electric connector. Use absorbent pads to place in your working area for any fuel spills prevention. After releasing the lock tab the fuel level sensor should be rotated counterclockwise for one-fourth of a turn and then lifted out. Check the fuel level sensor flange mating surfaces but do not adjust or polish the area that touches the fuel tank O-ring seal. A new fuel level sensor or fuel tank must be installed when the O-ring contact area shows bent or scratched or corroded condition. The installation process requires the O-ring seal to receive a treatment of clean engine oil. The installation requires users to apply strong pressure on the fuel level sensor while rotating it clockwise until the lock arrow matches the tank notch at less than 15 Nm (133 lb-in) of torque. Complete the installation by following the reverse steps of removal.