How to Service and Repair the 6F50 Motor And Transmission Mount on Ford Edge?

A hoist in neutral position allows the technician to proceed with servicing and repairing the 6F50 transmission mount. The service requires first loosening the clamp on the exhaust flexible pipe before unhanging both exhaust hangers and removing a four-nut assembly with exhaust flexible pipe and Y-pipe along with discarding the nuts and gasket. Begin service by taking away the two nuts from the roll restrictor heat shield then move to unfasten the roll restrictor-to-subframe through bolt before removing bolts from the roll restrictor bracket. After detaching the roll restrictor-to-transaxle through bolt it is possible to remove the roll restrictor. The next work step involves uninstalling three bolts along with the roll restrictor bracket. The mass air flow sensor electrical connector and wiring harness fastener must be removed from the air cleaner assembly together with separate disconnects of the brake booster vacuum hose and the engine breather. First remove the ACL assembly bracket bolt then loosen the ACL outlet pipe clamp at the throttle body before taking out the ACL with its outlet pipe assembly. First disconnect all wiring harness fasteners then remove the three bolts before extracting the battery together with the battery tray. Correct positioning of the oil pan holding fixture against the oil pan mounting bosses ensures prevention of any damage to those areas. A floor jack together with the oil pan holding fixture should elevate the engine to release pressure from the transaxle support insulator. Start by removing the transaxle support insulator through bolt and flagnut and then proceed to disconnect the three nuts and remove the bolt and bracket from the insulator. Lower the jack while ensuring the transmission fluid cooler tube passes beyond the lower transmission support insulator bolts followed by unbolted battery tray support bracket fasteners and detached top and bottom transaxle support insulator fasteners. When installing the bottom transaxle support insulator bolts apply a torque of 55 Nm (41 lb-ft) before moving to top bolts that should also have 55 Nm (41 lb-ft) torque. The installation requires tightening the battery tray support bracket bolts to 10 Nm (89 lb-in). Lift the transaxle into position using the jack and oil pan holding fixture followed by installation of the transaxle support insulator bracket with bolt and nuts and tightening the nuts to 63 Nm (46 lb-ft) while the bolt requires 80 Nm (59 lb-ft). Fasten the transaxle support insulator through bolt by tightening it with a torque of 175 Nm (129 lb-ft) while using a flagnut. Before restoration of service, reinstall the battery tray along with three bolts tightened at 10 Nm (89 lb-in) torque. Then connect all wiring harness fasteners. After placing the battery in its position you should install the ACL assembly while tightening the bolt to 11 Nm (97 lb-in). Attach the engine breather and brake booster vacuum hoses onto the ACL assembly while tightening the MAF sensor electrical connector and wiring harness fastening. Keep the ACL outlet pipe clamp at the TB fastened to 5 Nm (44 lb-in). Screw in and tighten three bolts on the roll restrictor bracket that sits on the transaxle until they reach 90 Nm (66 lb-ft). Position the roll restrictor bracket onto the transaxle before installing three bolts which should be tightened to 90 Nm (66 lb-ft) and the roll restrictor-to-transaxle through bolt to 115 Nm (85 lb-ft). Install the roll restrictor-to-subframe through bolt and tighten it to 103 Nm (76 lb-ft). Then attach the roll restrictor heat shield by securing its two nuts to 11 Nm (97 lb-in). The final task requires you to mount the exhaust Y-pipe with its new gasket and four new nuts at 40 Nm (30 lb-ft), reinstall exhaust hangers and secure the exhaust clamp to 40 Nm (30 lb-ft), after which you should validate the transmission fluid level while making necessary fluid additions with clean fluid.

OEM Ford Edge Motor And Transmission Mount

Motor and Trans Mount

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

29 Motor And Transmission Mounts found

View related parts
Ford Edge Motor Mount, Front Part Number: DP5Z-6038-B
$121.37 MSRP: $176.67
You Save: $55.30 (32%)
ADD TO CART
Product Specifications
- Other Name: Bracket - Engine Front Support; Engine Mount, Front; Engine Mount Bracket; Front Mount; Mount
- Position: Front
- Replaces: DP5Z-6038-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2015-2018 Ford Edge | SE, SEL, Titanium | 6 Cyl 3.5 L GAS
View related parts
Ford Edge Transmission Mount, Lower Part Number: DP5Z-6068-H
$111.39 MSRP: $171.42
You Save: $60.03 (36%)
ADD TO CART
Product Specifications
- Other Name: Automatic Transmission Mount, Lower; Engine Torque Strut; Transfer Case Mount; Motor Mount; Torque Arm; Lower Trans Mount; Torsion Damper
- Position: Lower
- Replaces: DP5Z-6068-G, DP5Z-6068-B
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2015-2018 Ford Edge | SE, SEL, Titanium | 6 Cyl 3.5 L GAS
View related parts
Ford Edge Transmission Mount, Lower Part Number: F2GZ-6068-A
$94.59 MSRP: $137.68
You Save: $43.09 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Housing; Engine Torque Strut; Engine Mount Torque Strut; Transfer Case Mount; Motor Mount; Torque Arm; Support Strut; Mount
- Position: Lower
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2015-2024 Ford Edge | Sport, ST | 6 Cyl 2.7 L GAS
View related parts
Ford Edge Mount Bracket, Front Passenger Side Part Number: 8M8Z-6038-A
$63.73 MSRP: $97.90
You Save: $34.17 (35%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bracket - Engine Mounting; Front Engine Mount Support; Right Engine Mount Bracket; Torque Strut; Motor Mount.; Engine Bracket; Front Mount; Front Mount Bracket; Support; Mount
- Manufacturer Note: Bracket
- Position: Front Passenger Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2007-2014 Ford Edge | Limited, SE, SEL, SEL Plus, Sport | 6 Cyl 3.5 L GAS
View related parts
Ford Edge Upper Arm Part Number: F2GZ-6068-B
$99.37 MSRP: $144.65
You Save: $45.28 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Automatic Transmission Mount; Engine Torque Strut; Engine Support Rod; Transfer Case Mount; Motor Mount.; Transmission Mount; Torque Strut
- Position: Upper
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2015-2018 Ford Edge | Sport | 6 Cyl 2.7 L GAS
View related parts
Ford Edge Motor Mount, Passenger Side Part Number: CT4Z-6038-C
$77.08 MSRP: $112.20
You Save: $35.12 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Bracket - Engine Front Support; Engine Mount; Engine Mount Bracket; Mount
- Manufacturer Note: Bracket And Insulator
- Position: Passenger Side
- Replaces: CT4Z-6038-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2012-2014 Ford Edge | Limited, SE, SEL | 4 Cyl 2.0 L GAS
View related parts
Ford Edge Transmission Mount Part Number: DT4Z-6068-A
$61.54 MSRP: $89.58
You Save: $28.04 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Housing; Engine Torque Strut; Engine Mount Torque Strut; Transfer Case Mount; Torque Arm
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2011-2014 Ford Edge | Limited, SE, SEL, Sport | 6 Cyl 3.5 L GAS, 6 Cyl 3.7 L GAS
View related parts
Ford Edge Transmission Mount Part Number: 8T4Z-6068-A
$53.59 MSRP: $76.67
You Save: $23.08 (31%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Housing; Transfer Case Mount
- Replaced by: 8T4Z-6068-B
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2007-2008 Ford Edge | Limited, SE, SEL, SEL Plus | 6 Cyl 3.5 L GAS
View related parts
Ford Edge Transmission Mount Bracket, Driver Side Part Number: DT4Z-6031-A
$62.85 MSRP: $91.48
You Save: $28.63 (32%)
ADD TO CART
Product Specifications
- Other Name: Bracket - Engine Mounting; Automatic Transmission Mount Bracket; Transfer Case Mount; Transmission Mount
- Manufacturer Note: INSULATOR
- Position: Driver Side
- Replaces: 7T4Z-6031-AA, 8T4Z-6031-B, BT4Z-6068-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2011-2014 Ford Edge | Limited, SE, SEL, Sport | 6 Cyl 3.5 L GAS, 6 Cyl 3.7 L GAS
View related parts
Ford Edge Bracket Part Number: HP5Z-6E042-A
$64.11 MSRP: $93.32
You Save: $29.21 (32%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Engine Torque Strut Bracket; Motor Mount
- Replaces: DP5Z-6E042-B
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2015-2016 Ford Edge | SE, SEL, Titanium | 6 Cyl 3.5 L GAS
View related parts
Ford Edge Upper Arm Part Number: K2GZ-6068-B
$90.94 MSRP: $132.37
You Save: $41.43 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Housing; Engine Torque Strut; Engine Mount Torque Strut; Transmission Mount; Motor Mount; Torque Arm; Mount
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2015-2024 Ford Edge | Sport, ST | 6 Cyl 2.7 L GAS
View related parts
Ford Edge Transmission Mount Part Number: K2GZ-6068-J
$150.00 MSRP: $218.33
You Save: $68.33 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Housing - Transmission Extension; Transmission Mount Bracket
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2019-2024 Ford Edge | ST | 6 Cyl 2.7 L GAS
View related parts
Ford Edge Motor Mount Part Number: F2GZ-6038-A
$201.27 MSRP: $313.50
You Save: $112.23 (36%)
ADD TO CART
Product Specifications
- Other Name: Bracket - Engine Front Support; Engine Mount; Engine Mount Bracket; Mount
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2015-2018 Ford Edge | Sport | 6 Cyl 2.7 L GAS
View related parts
Ford Edge Transmission Mount, Upper Part Number: DP5Z-6068-C
$108.29 MSRP: $166.65
You Save: $58.36 (36%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Housing; Engine Torque Strut; Engine Support Rod; Engine Mount Torque Strut; Transfer Case Mount; Motor Mount; Torque Arm; Torque Strut
- Position: Upper
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2015-2018 Ford Edge | SE, SEL, Titanium | 6 Cyl 3.5 L GAS
View related parts
Ford Edge Engine Bracket, Driver Side Part Number: 8T4Z-6031-B
$62.85 MSRP: $91.48
You Save: $28.63 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Bracket - Engine Mount; Engine Mount Bracket, Left; Motor Mount; Bracket - Engine Mounting
- Manufacturer Note: INSULATOR
- Position: Driver Side
- Replaced by: DT4Z-6031-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2007-2010 Ford Edge | Limited, SE, SEL, SEL Plus, Sport | 6 Cyl 3.5 L GAS
View related parts
Ford Edge Bracket Part Number: F2GZ-6038-C
$46.65 MSRP: $69.85
You Save: $23.20 (34%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Bracket - Engine Mounting; Engine Mount Bracket; Transmission Mount; Motor Mount
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2015-2024 Ford Edge | Sport, ST | 6 Cyl 2.7 L GAS
View related parts
Ford Edge Transmission Mount Damper, Lower Part Number: F2GZ-6F028-A
$29.47 MSRP: $41.80
You Save: $12.33 (30%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Damper Assembly; Automatic Transmission Mount Insulator; Engine Mount Isolator, Lower; Transfer Case Mount; Motor Mount; Damper; Transmission Mount
- Position: Lower
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2015-2024 Ford Edge | SE, SEL, ST-Line, Titanium | 4 Cyl 2.0 L GAS
View related parts
Ford Edge Motor Mount Part Number: K2GZ-6038-A
$158.70 MSRP: $231.00
You Save: $72.30 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Bracket - Engine Front Support; Engine Mount; Engine Mount Bracket; Side Mount; Mount
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2019-2024 Ford Edge | ST | 6 Cyl 2.7 L GAS
View related parts
Ford Edge Transmission Mount, Driver Side Part Number: CT4Z-6038-B
$87.48 MSRP: $127.33
You Save: $39.85 (32%)
Product Specifications
- Other Name: Insulator Assembly; Automatic Transmission Mount; Engine Mount Bracket; Transfer Case Mount; Motor Mount; Mount
- Manufacturer Note: INSULATOR
- Position: Driver Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2012-2014 Ford Edge | Limited, SE, SEL | 4 Cyl 2.0 L GAS
View related parts
Ford Edge Transmission Mount Bracket, Driver Side Part Number: CT4Z-6031-A
$71.45 MSRP: $104.00
You Save: $32.55 (32%)
Product Specifications
- Other Name: Bracket - Engine Mounting; Automatic Transmission Mount Bracket; Transfer Case Mount; Transmission Mount
- Manufacturer Note: Bracket
- Position: Driver Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2012-2014 Ford Edge | Limited, SE, SEL | 4 Cyl 2.0 L GAS

| Page 1 of 2 |Next >

1-20 of 29 Results

Ford Edge Motor And Transmission Mount

OEM Motor And Transmission Mount boasts unmatched quality. Each part goes through full quality checks. They adhere to Ford's official factory standards. These steps remove flaws and inconsistencies. So you can get Motor And Transmission Mount with long life and a perfect fit. Come to our website and find genuine Ford Edge parts. We keep a wide inventory of OEM Edge parts at the highly affordable prices. It's easy to search, compare, and pick what you need. You'll love the clear info and simple checkout. We offer top-rated customer service, and we reply fast. We also ship promptly to ensure your order arrives on time.

Motor And Transmission Mount is one of the significant components of a Ford Edge car, as it fixes the transmission in place and protects it against the vibrations produced by the engine. Depending on the type/ model of the transmission used in Ford Edge, it is probable that there is one or several Motor And Transmission Mounts. These mounts are equipped with properties that help to absorb and decrease vibrations thus improving on the driving experience. As the years went by Ford Edge cars, different forms of Motor And Transmission Mounts were implemented to boost performance and steadiness of the cars. The primary of these may concern the design and the material of which these types are made, and how well they transmit the vibration isolations, or how durable they are. The Motor And Transmission Mount is crucial for the proper functioning of the transmission system of the Ford Edge thus affecting the functionality as well as the comfort of the car.

Ford Edge Motor And Transmission Mount Parts and Q&A

Transmission Mount, Driver Side
7A1Z-6038-AA
Q: How to Service and Repair the 6F50 Motor And Transmission Mount on Ford Edge?
A:
A hoist in neutral position allows the technician to proceed with servicing and repairing the 6F50 transmission mount. The service requires first loosening the clamp on the exhaust flexible pipe before unhanging both exhaust hangers and removing a four-nut assembly with exhaust flexible pipe and Y-pipe along with discarding the nuts and gasket. Begin service by taking away the two nuts from the roll restrictor heat shield then move to unfasten the roll restrictor-to-subframe through bolt before removing bolts from the roll restrictor bracket. After detaching the roll restrictor-to-transaxle through bolt it is possible to remove the roll restrictor. The next work step involves uninstalling three bolts along with the roll restrictor bracket. The Mass Air Flow Sensor electrical connector and wiring harness fastener must be removed from the air cleaner assembly together with separate disconnects of the brake booster vacuum hose and the engine breather. First remove the ACL assembly bracket bolt then loosen the ACL outlet pipe clamp at the Throttle Body before taking out the ACL with its outlet pipe assembly. First disconnect all wiring harness fasteners then remove the three bolts before extracting the battery together with the battery tray. Correct positioning of the oil pan holding fixture against the oil pan mounting bosses ensures prevention of any damage to those areas. A floor jack together with the oil pan holding fixture should elevate the engine to release pressure from the transaxle support insulator. Start by removing the transaxle support insulator through bolt and flagnut and then proceed to disconnect the three nuts and remove the bolt and bracket from the insulator. Lower the jack while ensuring the transmission fluid cooler tube passes beyond the lower transmission support insulator bolts followed by unbolted battery tray support bracket fasteners and detached top and bottom transaxle support insulator fasteners. When installing the bottom transaxle support insulator bolts apply a torque of 55 Nm (41 lb-ft) before moving to top bolts that should also have 55 Nm (41 lb-ft) torque. The installation requires tightening the battery tray support bracket bolts to 10 Nm (89 lb-in). Lift the transaxle into position using the jack and oil pan holding fixture followed by installation of the transaxle support insulator bracket with bolt and nuts and tightening the nuts to 63 Nm (46 lb-ft) while the bolt requires 80 Nm (59 lb-ft). Fasten the transaxle support insulator through bolt by tightening it with a torque of 175 Nm (129 lb-ft) while using a flagnut. Before restoration of service, reinstall the battery tray along with three bolts tightened at 10 Nm (89 lb-in) torque. Then connect all wiring harness fasteners. After placing the battery in its position you should install the ACL assembly while tightening the bolt to 11 Nm (97 lb-in). Attach the engine breather and brake booster vacuum hoses onto the ACL assembly while tightening the MAF sensor electrical connector and wiring harness fastening. Keep the ACL outlet pipe clamp at the TB fastened to 5 Nm (44 lb-in). Screw in and tighten three bolts on the roll restrictor bracket that sits on the transaxle until they reach 90 Nm (66 lb-ft). Position the roll restrictor bracket onto the transaxle before installing three bolts which should be tightened to 90 Nm (66 lb-ft) and the roll restrictor-to-transaxle through bolt to 115 Nm (85 lb-ft). Install the roll restrictor-to-subframe through bolt and tighten it to 103 Nm (76 lb-ft). Then attach the roll restrictor heat shield by securing its two nuts to 11 Nm (97 lb-in). The final task requires you to mount the exhaust Y-pipe with its new gasket and four new nuts at 40 Nm (30 lb-ft), reinstall exhaust hangers and secure the exhaust clamp to 40 Nm (30 lb-ft), after which you should validate the transmission fluid level while making necessary fluid additions with clean fluid.