What Precautions Should Be Taken When Servicing the Front ABS Control Module on Ford Escape?

Workers servicing the Escape Hybrid Hydraulic Control Unit (HCU) need to wear high voltage insulated safety gloves combined with a face shield because the traction battery along with charging system contains high voltage components which pose a severe risk of death or injury. Brake fluid that contains polyglycol ethers and polyglycols requires users to prevent eye contact and to wash their hands properly after usage. Any eye exposure requires immediate flushing with running water for 15 minutes while patients needing continued medical care should remain under observation. Ingesting brake fluid requires you to consume water followed by vomiting before going to a medical center at once. Any brake fluid spillages should be cleansed immediately by using water because the fluid will potentially harm painted and plastic materials. A new ABS module must be handled as a single unit with the HCU because performing as-built configuration using vehicle data is necessary before installation. A mechanism must be used to depressurize the HCU before mechanical work begins and this process can be checked by marking and observing a 12 mm (0.47 inch) increase in master cylinder brake fluid level. The vehicle requires 4 minutes of rest in OFF position to depressurize without door opening and by avoiding the brake pedal usage. Secure a power connection out of the battery and deactivate the high voltage battery followed by extracting the battery Junction box fuses 24 (50A) and 31 (50A). The first step involves taking out 2 pin-type fasteners from the HCU heat shield followed by rotating its electrical connector cover for disconnection and unclipping the brake fluid low pressure feed and return hoses. Write down the brake lines' sequence before taking off their 10 mm and 12 mm fittings from the HCU then tighten them to 18 Nm (13 ft. lbs.) when reattaching the brake lines. Loosen and tighten the HCU bracket-to-frame bolts to 23 Nm (17 ft. lbs.) before uninstalling and later install. Unfasten the brake line from its routing clip found at the bottom of the HCU bracket. The first step is to remove the HCU bracket bolt that retains the A/C line routing then proceed with HCU disassembly. During reinstallation users must apply an appropriate lubricating substance while making sure brake line crossings do not occur because this could generate DTC(s) during ABS events. The installation requires the same reverse steps with a correct bleed procedure for the brake system.

How to Service and Repair the ABS Control Module in the Hydraulic Control Assembly on Ford Escape?

Treatment and repair work of the antilock brake Hydraulic Control Assembly must begin by disconnecting the battery's ground cable. Detach the air cleaner together with the outlet pipe after disconnecting brake line fittings from the HCU. Tighten these fittings to 15 Nm (11 ft. lbs.) when reinstalling everything. The HCU-to-master cylinder brake tube fittings should be removed from cars with 3.0L engines by following the same tightening specification when reinstalling. The next step involves removing three HCU bracket-to-frame bolts before reassembly where they need to be tightened at 23 Nm (17 ft. lbs.). First turn the protective cover to disconnect the electrical connector and afterward remove the three bracket-to-HCU bolts by torquing them to 9 Nm (80 inch lbs.) during reinstallation. Proceed to remove the HCU but before doing so disconnect all three screws securing the ABS module then follow the recommended torque value of 2 Nm (18 inch lbs.) during reinstallation. Return the gearbox after completing removal then follow procedure to bleed the brake system. Exercise care when using brake fluid since any contact may result in personal harm and surface destruction along with sensitivity of electronic modules to electrical charges.

OEM Ford Escape ABS Control Module

Anti Lock Brake Control Module

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

28 ABS Control Modules found

View related parts
Ford Escape Control Module Part Number: 8L8Z-2C219-D
$522.10 MSRP: $707.69
You Save: $185.59 (27%)
ADD TO CART
Product Specifications
- Other Name: Control; ABS Modulator Valve; ABS Control Module; Controller
- Replaces: 8L8Z-2C219-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2008 Ford Escape | Hybrid, Limited, XLS, XLT | 4 Cyl 2.3 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.3 L GAS, 6 Cyl 3.0 L GAS
View related parts
Ford Escape Control Module Part Number: BL8Z-2C219-A
$471.21 MSRP: $540.00
You Save: $68.79 (13%)
ADD TO CART
Product Specifications
- Other Name: Control; ABS Modulator Valve; ABS Control Module; Controller
- Replaces: BL8Z-2C219-B
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2011-2012 Ford Escape | Limited, XLS, XLT | 4 Cyl 2.5 L GAS, 6 Cyl 3.0 L FLEX
View related parts
Ford Escape Modulator Valve Part Number: CV6Z-2C405-E
$1022.74 MSRP: $1283.33
You Save: $260.59 (21%)
ADD TO CART
Product Specifications
- Other Name: Unit Assembly - Control; ABS Hydraulic Assembly; ABS Control Module; ABS Control Unit
- Replaces: CV6Z-2C405-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2013-2015 Ford Escape | S, SE, SEL, Titanium | 4 Cyl 1.6 L GAS, 4 Cyl 2.0 L GAS, 4 Cyl 2.5 L GAS
View related parts
Ford Escape Modulator Valve Part Number: LX6Z-2B373-J
$782.10 MSRP: $1069.54
You Save: $287.44 (27%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Valve Assembly - Modulator; ABS Control Module; ABS Control Unit
- Replaces: LX6Z-2B373-H, LX6Z-2B373-G
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2020-2022 Ford Escape | S, SE, SE Hybrid, SE Plug-In Hybrid, SE Sport Hybrid, SEL, SEL Hybrid, SEL Plug-In Hybrid, Titanium, Titanium Hybrid, Titanium Plug-In Hybrid | 3 Cyl 1.5 L GAS, 4 Cyl 2.0 L GAS, 4 Cyl 2.5 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.5 L PLUG-IN HYBRID EV-GAS (PHEV)
View related parts
Ford Escape Control Module Part Number: LX6Z-2C219-M
$440.38 MSRP: $596.92
You Save: $156.54 (27%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Kit - Brake Anti-Lock Actuator; ABS Control Module
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2022 Ford Escape | S, SE, SE Hybrid, SE Plug-In Hybrid, SEL, SEL Hybrid, SEL Plug-In Hybrid, Titanium, Titanium Hybrid, Titanium Plug-In Hybrid | 3 Cyl 1.5 L GAS, 4 Cyl 2.0 L GAS, 4 Cyl 2.5 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.5 L PLUG-IN HYBRID EV-GAS (PHEV)
View related parts
Ford Escape Modulator Valve Part Number: LX6Z-2B373-M
$268.57 MSRP: $386.15
You Save: $117.58 (31%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Valve Assembly - Modulator; ABS Control Unit
- Replaces: LX6Z-2B373-C
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2020 Ford Escape | S, SE, SE Plug-In Hybrid, SE Sport Hybrid, SEL, SEL Plug-In Hybrid, Titanium, Titanium Hybrid, Titanium Plug-In Hybrid | 3 Cyl 1.5 L GAS, 4 Cyl 2.0 L GAS, 4 Cyl 2.5 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.5 L PLUG-IN HYBRID EV-GAS (PHEV)
View related parts
Ford Escape Control Module Part Number: GV6Z-2C219-J
$470.68 MSRP: $638.00
You Save: $167.32 (27%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Control; ABS Control Module
- Replaces: GV6Z-2C219-C
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2013-2019 Ford Escape | S, SE, SEL, Titanium | 4 Cyl 1.5 L GAS, 4 Cyl 1.6 L GAS, 4 Cyl 2.0 L GAS, 4 Cyl 2.5 L GAS
View related parts
Ford Escape Modulator Valve Part Number: LX6Z-2B373-L
$949.50 MSRP: $1298.46
You Save: $348.96 (27%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Valve Assembly - Modulator; ABS Control Unit
- Replaces: LX6Z-2B373-K
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2022-2023 Ford Escape | Active, Base, Platinum, Platinum Hybrid, Plug-In Hybrid, S, SE, SE Hybrid, SE Plug-In Hybrid, SEL, SEL Hybrid, SEL Plug-In Hybrid, ST-Line, ST-Line Elite, ST-Line Elite Hybrid, ST-Line Hybrid, ST-Line Select, ST-Line Select Hybrid, Titanium, Titanium Hybrid, Titanium Plug-In Hybrid | 3 Cyl 1.5 L GAS, 4 Cyl 2.0 L GAS, 4 Cyl 2.5 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.5 L PLUG-IN HYBRID EV-GAS (PHEV)
View related parts
Ford Escape Control Module Part Number: LX6Z-2C219-R
$622.13 MSRP: $850.77
You Save: $228.64 (27%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Kit - Brake Anti-Lock Actuator
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2022-2023 Ford Escape | Active, Base, Platinum, Platinum Hybrid, Plug-In Hybrid, S, SE, SE Hybrid, SE Plug-In Hybrid, SEL, SEL Hybrid, SEL Plug-In Hybrid, ST-Line, ST-Line Elite, ST-Line Elite Hybrid, ST-Line Hybrid, ST-Line Select, ST-Line Select Hybrid, Titanium, Titanium Hybrid, Titanium Plug-In Hybrid | 3 Cyl 1.5 L GAS, 4 Cyl 2.0 L GAS, 4 Cyl 2.5 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.5 L PLUG-IN HYBRID EV-GAS (PHEV)
View related parts
Ford Escape Control Module Part Number: LX6Z-2C219-K
$480.67 MSRP: $651.54
You Save: $170.87 (27%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Kit - Brake Anti-Lock Actuator
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2020-2021 Ford Escape | S, SE, SE Hybrid, SE Plug-In Hybrid, SE Sport Hybrid, SEL, SEL Hybrid, SEL Plug-In Hybrid, Titanium, Titanium Hybrid, Titanium Plug-In Hybrid | 3 Cyl 1.5 L GAS, 4 Cyl 2.0 L GAS, 4 Cyl 2.5 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.5 L PLUG-IN HYBRID EV-GAS (PHEV)
View related parts
Ford Escape Control Module Part Number: LX6Z-2C219-D
$566.82 MSRP: $768.31
You Save: $201.49 (27%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Kit - Brake Repair; ABS Control Module
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2020 Ford Escape | S, SE, SE Plug-In Hybrid, SE Sport Hybrid, SEL, SEL Plug-In Hybrid, Titanium, Titanium Hybrid, Titanium Plug-In Hybrid | 3 Cyl 1.5 L GAS, 4 Cyl 2.0 L GAS, 4 Cyl 2.5 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.5 L PLUG-IN HYBRID EV-GAS (PHEV)
View related parts
Ford Escape ABS Control Unit Part Number: 5L8Z-2B373-AC
Product Specifications
- Other Name: Control; ABS Hydraulic Assembly; ABS Control Module
- Replaces: 5L8Z-2B373-AB
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2005-2007 Ford Escape | Limited, XLS, XLT, XLT No Boundaries, XLT Sport | 4 Cyl 2.3 L GAS, 6 Cyl 3.0 L GAS
View related parts
Ford Escape Modulator Valve Part Number: 8M6Z-2C286-A
Product Specifications
- Other Name: Control Assembly - ABS Hydraulics; ABS Hydraulic Assembly; ABS Control Module; ABS Control Unit
- Manufacturer Note: ECU & HCU
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2007-2008 Ford Escape | Hybrid | 4 Cyl 2.3 L FULL HYBRID EV-GAS (FHEV)
View related parts
Ford Escape Modulator Valve Part Number: YL8Z-2C286-DA
Product Specifications
- Other Name: Control Assembly - ABS Hydraulic; ABS Control Module; Module; Control Assembly - ABS Hydraulics
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2001-2004 Ford Escape | Limited, XLS, XLT | 4 Cyl 2.0 L GAS, 6 Cyl 3.0 L GAS
View related parts
Ford Escape Modulator Valve Part Number: 8L8Z-2C346-D
$727.88 MSRP: $1078.33
You Save: $350.45 (33%)
Product Specifications
- Other Name: Module - ABS Control; ABS Control Module; Module
- Replaces: 8L8Z-2C346-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2008 Ford Escape | Hybrid, Limited, XLS, XLT | 4 Cyl 2.3 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.3 L GAS, 6 Cyl 3.0 L GAS
View related parts
Ford Escape Modulator Valve Part Number: 7M6Z-2C286-B
Product Specifications
- Other Name: Control Assembly - ABS Hydraulics; ABS Hydraulic Assembly; ABS Control Module; ABS Control Unit
- Manufacturer Note: ECU & HCU
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2005-2007 Ford Escape | Hybrid | 4 Cyl 2.3 L FULL HYBRID EV-GAS (FHEV)
View related parts
Ford Escape ABS Control Unit Part Number: 5L8Z-2B373-BC
Product Specifications
- Other Name: Control; ABS Control Module
- Replaces: 5L8Z-2B373-BB
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2005-2007 Ford Escape | Limited, XLS, XLT, XLT No Boundaries, XLT Sport | 4 Cyl 2.3 L GAS, 6 Cyl 3.0 L GAS
View related parts
Ford Escape Modulator Valve Part Number: CV6Z-2C405-G
Product Specifications
- Other Name: Unit Assembly - Control; ABS Hydraulic Assembly; ABS Control Module; ABS Control Unit
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2016 Ford Escape | S, SE, Titanium | 4 Cyl 1.6 L GAS, 4 Cyl 2.0 L GAS, 4 Cyl 2.5 L GAS
View related parts
Ford Escape Modulator Valve Part Number: GV6Z-2C405-G
$770.63 MSRP: $1141.67
You Save: $371.04 (33%)
Product Specifications
- Other Name: Unit Assembly - Control; ABS Hydraulic Assembly; ABS Control Module; ABS Control Unit
- Manufacturer Note: ECU & HCU
- Replaces: GV6Z-2C405-D, GV6Z-2C405-B
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2017-2019 Ford Escape | S, SE, SEL, Titanium | 4 Cyl 1.5 L GAS, 4 Cyl 2.0 L GAS, 4 Cyl 2.5 L GAS
View related parts
Ford Escape Modulator Valve Part Number: 6L8Z-2C286-A
Product Specifications
- Other Name: Control Assembly - ABS Hydraulics; ABS Control Module; Module
- Replaces: 5L8Z-2C286-AA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2005-2007 Ford Escape | Limited, XLS, XLT, XLT No Boundaries, XLT Sport | 4 Cyl 2.3 L GAS, 6 Cyl 3.0 L GAS

| Page 1 of 2 |Next >

1-20 of 28 Results

Ford Escape ABS Control Module

OEM ABS Control Module boasts unmatched quality. Each part goes through full quality checks. They adhere to Ford's official factory standards. These steps remove flaws and inconsistencies. So you can get ABS Control Module with long life and a perfect fit. Come to our website and find genuine Ford Escape parts. We keep a wide inventory of OEM Escape parts at the highly affordable prices. It's easy to search, compare, and pick what you need. You'll love the clear info and simple checkout. We offer top-rated customer service, and we reply fast. We also ship promptly to ensure your order arrives on time.

The Ford Escape ABS Control Module is a central part in the Ford Escape's Anti-lock Braking System; which is well known for dependability and durability. This particular module is very important to prevent wheel lock-up during hard braking and this coupled with improvements in safety and performance makes this a very important one as per my perception. With the help of the wheel speed sensors, valves, a pump, and the ECU, the Ford Escape ABS Control Module is always able to measure the current speed of the wheels and control the brake pressure to deliver the premier possible ABS performance in any situation. This brand ABS Control Module can fit most Ford Escape generations from the second to the fourth one and is improved with additional features like electronic stability control with traction control to ensure that the vehicle will behave more responsive to the driver's inputs. So, the integrated design of Ford Escape with the help of the ABS Control Module gives the better ability to steer and needed stopping distance on various surfaces of the road. And although it may decrease the road holding factor on loose gravel or snow by roughly the same margin effective countering the gain in safety and driving pleasure is indisputable. First, the Ford Escape ABS Control Module is known in the market due to the incorporation of new technology and second, it ensures safe driving to the vehicle's users. Therefore, Ford Escape ABS Control Module is still worth its salt because of the positive impression it has made in the market among users of Ford Escape.

Ford Escape ABS Control Module Parts and Q&A

ABS Control Unit
5L8Z-2B373-BC
Q: What Precautions Should Be Taken When Servicing the Front ABS Control Module on Ford Escape?
A:
Workers servicing the Escape Hybrid Hydraulic Control Unit (HCU) need to wear high voltage insulated safety gloves combined with a face shield because the traction battery along with charging system contains high voltage components which pose a severe risk of death or injury. Brake fluid that contains polyglycol ethers and polyglycols requires users to prevent eye contact and to wash their hands properly after usage. Any eye exposure requires immediate flushing with running water for 15 minutes while patients needing continued medical care should remain under observation. Ingesting brake fluid requires you to consume water followed by vomiting before going to a medical center at once. Any brake fluid spillages should be cleansed immediately by using water because the fluid will potentially harm painted and plastic materials. A new ABS module must be handled as a single unit with the HCU because performing as-built configuration using vehicle data is necessary before installation. A mechanism must be used to depressurize the HCU before mechanical work begins and this process can be checked by marking and observing a 12 mm (0.47 inch) increase in master cylinder brake fluid level. The vehicle requires 4 minutes of rest in OFF position to depressurize without door opening and by avoiding the brake pedal usage. Secure a power connection out of the battery and deactivate the high voltage battery followed by extracting the battery Junction box fuses 24 (50A) and 31 (50A). The first step involves taking out 2 pin-type fasteners from the HCU heat shield followed by rotating its electrical connector cover for disconnection and unclipping the brake fluid low pressure feed and return hoses. Write down the brake lines' sequence before taking off their 10 mm and 12 mm fittings from the HCU then tighten them to 18 Nm (13 ft. lbs.) when reattaching the brake lines. Loosen and tighten the HCU bracket-to-frame bolts to 23 Nm (17 ft. lbs.) before uninstalling and later install. Unfasten the brake line from its routing clip found at the bottom of the HCU bracket. The first step is to remove the HCU bracket bolt that retains the A/C line routing then proceed with HCU disassembly. During reinstallation users must apply an appropriate lubricating substance while making sure brake line crossings do not occur because this could generate DTC(s) during ABS events. The installation requires the same reverse steps with a correct bleed procedure for the brake system.
ABS Control Unit
5L8Z-2B373-AC
Q: How to Service and Repair the ABS Control Module in the Hydraulic Control Assembly on Ford Escape?
A:
Treatment and repair work of the antilock brake Hydraulic Control Assembly must begin by disconnecting the battery's ground cable. Detach the air cleaner together with the outlet pipe after disconnecting brake line fittings from the HCU. Tighten these fittings to 15 Nm (11 ft. lbs.) when reinstalling everything. The HCU-to-master cylinder brake tube fittings should be removed from cars with 3.0L engines by following the same tightening specification when reinstalling. The next step involves removing three HCU bracket-to-frame bolts before reassembly where they need to be tightened at 23 Nm (17 ft. lbs.). First turn the protective cover to disconnect the electrical connector and afterward remove the three bracket-to-HCU bolts by torquing them to 9 Nm (80 inch lbs.) during reinstallation. Proceed to remove the HCU but before doing so disconnect all three screws securing the ABS module then follow the recommended torque value of 2 Nm (18 inch lbs.) during reinstallation. Return the gearbox after completing removal then follow procedure to bleed the brake system. Exercise care when using brake fluid since any contact may result in personal harm and surface destruction along with sensitivity of electronic modules to electrical charges.