How to service and repair the inner tie rod on Ford F-150?

Service and repair operations for inner tie rod should begin by placing the vehicle in neutral position at a hoist. The tie-rod jam nut needs loosening before removing the outer tie-rod end nut that you will discard. Separate the outer tie-rod end from the wheel knuckle with the Ball Joint Tool Separator while making a note of turn counts since these values will help during reinstallation. The maintenance of the inner tie rod begins by removing both the tie-rod end and the tie-rod jam nut from the end of the rod. Discard both clamps and pull away the bellows boot from the base of the steering gear. Position the steering gear at its center and use the correct size crowfoot wrench on the rack gear flat to stop the inner tie rod from turning. Assistance may be needed for removing the right-hand side. Review all parts intended for re-use then install necessary new components. Steer the steering gear towards the center position before using the crowfoot wrench to establish the inner tie rod while tightening it to 120 Nm (89 lb-ft). Before installation of the inner tie rod apply grease to both sides of the bellows boot groove and position it correctly at the steering gear housing bead. Fit the steering gear bellows boot onto its position while using Boot Clamp Pliers to tighten a new inner bellows boot clamp securely. You must position the steering gear bellows end in the middle of the two grooves on the inner tie rod to block internal leakage before using a new outer bellows boot clamp installation. Install the tie-rod end on the inner tie rod by threading in the jam nut and repeat the same turns as initially removed. Secure the tie-rod end with the wheel knuckle but install a new tie-rod end nut then tighten it to 85 lb-ft (115 Nm). Finally adjust the front toe by tightening the tie-rod end jam nut to 103 Nm (76 lb-ft).

OEM Ford F-150 Tie Rod

Steering Tie Rod

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

21 Tie Rods found

View related parts
Ford F-150 Inner Tie Rod Part Number: GL3Z-3280-A
$63.76 MSRP: $104.91
You Save: $41.15 (40%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Kit - Tie Rod; Inner Tie Rod End; Tie Rod End
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2017-2020 Ford F-150 | King Ranch, Lariat, Limited, Platinum, Police Responder, Raptor, SSV, XL, XLT | 6 Cyl 2.7 L GAS, 6 Cyl 3.0 L DIESEL, 6 Cyl 3.3 L FLEX, 6 Cyl 3.5 L FLEX, 6 Cyl 3.5 L GAS, 8 Cyl 5.0 L FLEX
View related parts
Ford F-150 Inner Tie Rod Part Number: AL3Z-3280-A
$49.50 MSRP: $81.45
You Save: $31.95 (40%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Rod; Steering Tie Rod End, Inner
- Position: Inner
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2010-2014 Ford F-150 | SVT Raptor | 8 Cyl 5.4 L FLEX, 8 Cyl 6.2 L GAS
View related parts
Ford F-150 Inner Tie Rod Part Number: 6L3Z-3280-B
$32.52 MSRP: $51.64
You Save: $19.12 (38%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Rod; Steering Tie Rod End, Inner; Inner Tie Rod End; Tie Rod End
- Manufacturer Note: When Replacing Inner Tie Rods, Use Boots & Clamps Listed To Ensure A Proper Seal And Minimize Contamination
- Position: Inner
- Replaces: 4L3Z-3280-DA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2004-2008 Ford F-150 | FX2, FX4, Harley-Davidson Edition, King Ranch, Lariat, Limited, STX, THE 60TH ANNIVERSARY EDITION, XL, XLT | 6 Cyl 4.2 L GAS, 8 Cyl 4.6 L GAS, 8 Cyl 5.4 L FLEX, 8 Cyl 5.4 L GAS
View related parts
Ford F-150 Inner Tie Rod Part Number: 9L3Z-3280-A
$49.35 MSRP: $78.36
You Save: $29.01 (38%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Rod; Steering Tie Rod Nut, Front Inner; Steering Tie Rod End, Inner; Inner Tie Rod End; Tie Rod End
- Position: Inner
- Replaces: 7L1Z-3280-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2009-2014 Ford F-150 | FX2, FX4, Harley-Davidson Edition, King Ranch, Lariat, Lariat Limited, Limited, Platinum, STX, XL, XLT | 6 Cyl 3.5 L GAS, 6 Cyl 3.7 L CNG, 6 Cyl 3.7 L FLEX, 6 Cyl 3.7 L LPG, 8 Cyl 4.6 L GAS, 8 Cyl 5.0 L FLEX, 8 Cyl 5.4 L FLEX, 8 Cyl 6.2 L GAS
View related parts
Ford F-150 Inner Tie Rod Part Number: FL3Z-3280-A
$56.80 MSRP: $93.45
You Save: $36.65 (40%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Kit - Tie Rod; Steering Tie Rod End, Inner; Inner Tie Rod End; Tie Rod End
- Position: Inner
- Replaces: BL3Z-3280-A, MEF-20
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2011-2016 Ford F-150 | FX2, FX4, Harley-Davidson Edition, King Ranch, Lariat, Lariat Limited, Limited, Platinum, SSV, STX, SVT Raptor, XL, XLT | 6 Cyl 2.7 L GAS, 6 Cyl 3.5 L FLEX, 6 Cyl 3.5 L GAS, 6 Cyl 3.7 L CNG, 6 Cyl 3.7 L FLEX, 6 Cyl 3.7 L LPG, 8 Cyl 5.0 L FLEX, 8 Cyl 6.2 L GAS
View related parts
Ford F-150 Inner Tie Rod Part Number: HL3Z-3280-A
$162.59 MSRP: $236.67
You Save: $74.08 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Kit - Tie Rod
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2017-2020 Ford F-150 | King Ranch, Lariat, Limited, Platinum, Police Responder, Raptor, SSV, XL, XLT | 6 Cyl 2.7 L GAS, 6 Cyl 3.0 L DIESEL, 6 Cyl 3.3 L FLEX, 6 Cyl 3.5 L FLEX, 6 Cyl 3.5 L GAS, 8 Cyl 5.0 L FLEX
View related parts
Ford F-150 Inner Tie Rod, Passenger Side Part Number: 2L3Z-3A130-DA
$47.74 MSRP: $80.00
You Save: $32.26 (41%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: End - Spindle Rod Connecting; Steering Tie Rod End, Right Inner; Outer Tie Rod End; Tie Rod End
- Position: Inner Passenger Side
- Replaces: F65Z-3A130-DA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1997-2004 Ford F-150 | Base, FX4, Harley-Davidson Edition, King Ranch, Lariat, Lightning, STX, XL, XLT | 6 Cyl 4.2 L GAS, 8 Cyl 4.6 L GAS, 8 Cyl 5.4 L BI-FUEL, 8 Cyl 5.4 L CNG, 8 Cyl 5.4 L GAS
View related parts
Ford F-150 Inner Tie Rod, Driver Side Part Number: 2L3Z-3A131-BA
$61.88 MSRP: $101.82
You Save: $39.94 (40%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: End - Spindle Rod Connecting; Steering Tie Rod End, Left Inner; Outer Tie Rod End; Tie Rod End
- Position: Inner Driver Side
- Replaces: F65Z-3A130-BB
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1997-2004 Ford F-150 | Base, FX4, Harley-Davidson Edition, King Ranch, Lariat, Lightning, STX, XL, XLT | 6 Cyl 4.2 L GAS, 8 Cyl 4.6 L GAS, 8 Cyl 5.4 L BI-FUEL, 8 Cyl 5.4 L CNG, 8 Cyl 5.4 L GAS
View related parts
Ford F-150 Inner Tie Rod, Driver Side Part Number: 2L3Z-3A131-AA
$34.73 MSRP: $56.73
You Save: $22.00 (39%)
ADD TO CART
Product Specifications
- Other Name: End - Spindle Rod Connecting; Steering Tie Rod End, Left, Left Inner; Outer Tie Rod End; Tie Rod End
- Position: Driver Side
- Replaces: F65Z-3A130-AB
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1997-2004 Ford F-150 | Base, Harley-Davidson Edition, King Ranch, Lariat, Lightning, STX, XL, XLT | 6 Cyl 4.2 L GAS, 8 Cyl 4.6 L GAS, 8 Cyl 5.4 L BI-FUEL, 8 Cyl 5.4 L CNG, 8 Cyl 5.4 L GAS
View related parts
Ford F-150 Tie Rod End, Driver Side Part Number: EOTZ3A131D
$9.06 MSRP: $12.54
You Save: $3.48 (28%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: End - Spindle Rod Connecting; Steering Tie Rod End; Outer Tie Rod End; Outer Tie Rod
- Position: Driver Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1984-1986 Ford F-150 | Base, XL, XLT, XLT Lariat | 6 Cyl 4.9 L GAS, 6 Cyl 4.9 L LPG, 8 Cyl 5.0 L GAS, 8 Cyl 5.8 L GAS, 8 Cyl 6.9 L DIESEL
View related parts
Ford F-150 Outer Tie Rod, Passenger Side Part Number: ML3Z-3A130-A
$128.24 MSRP: $203.64
You Save: $75.40 (38%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: End - Spindle Rod Connecting; Steering Tie Rod End, Right Outer; Outer Tie Rod End; Tie Rod End
- Position: Outer Passenger Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2021-2023 Ford F-150 | King Ranch, Lariat, Limited, Platinum, Police Responder, Raptor, Raptor R, SSV, Tremor, XL, XLT | 6 Cyl 2.7 L GAS, 6 Cyl 3.0 L DIESEL, 6 Cyl 3.3 L FLEX, 6 Cyl 3.5 L FULL HYBRID EV-GAS (FHEV), 6 Cyl 3.5 L GAS, 8 Cyl 5.0 L FLEX, 8 Cyl 5.2 L GAS
View related parts
Ford F-150 Outer Tie Rod, Driver Side Part Number: ML3Z-3A130-B
$73.64 MSRP: $123.64
You Save: $50.00 (41%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: End - Spindle Rod Connecting; Steering Tie Rod End, Left Outer; Outer Tie Rod End; Tie Rod End
- Position: Outer Driver Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2021-2023 Ford F-150 | King Ranch, Lariat, Limited, Platinum, Police Responder, Raptor, Raptor R, SSV, Tremor, XL, XLT | 6 Cyl 2.7 L GAS, 6 Cyl 3.0 L DIESEL, 6 Cyl 3.3 L FLEX, 6 Cyl 3.5 L FULL HYBRID EV-GAS (FHEV), 6 Cyl 3.5 L GAS, 8 Cyl 5.0 L FLEX, 8 Cyl 5.2 L GAS
View related parts
Ford F-150 Inner Tie Rod Part Number: 6L3Z-3280-A
$49.26 MSRP: $82.55
You Save: $33.29 (41%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Rod; Steering Tie Rod End, Inner; Inner Tie Rod End; Tie Rod End
- Manufacturer Note: When Replacing Inner Tie Rods, Use Boots & Clamps Listed To Ensure A Proper Seal And Minimize Contamination
- Position: Inner
- Replaces: 4L3Z-3280-CA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2004-2008 Ford F-150 | FX2, FX4, Harley-Davidson Edition, King Ranch, Lariat, Limited, STX, THE 60TH ANNIVERSARY EDITION, XL, XLT | 6 Cyl 4.2 L GAS, 8 Cyl 4.6 L GAS, 8 Cyl 5.4 L FLEX, 8 Cyl 5.4 L GAS
View related parts
Ford F-150 Inner Tie Rod Part Number: ML3Z-3280-B
$138.55 MSRP: $201.67
You Save: $63.12 (32%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Kit - Tie Rod; Steering Tie Rod End, Inner
- Position: Inner
- Replaced by: NL1Z-3280-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2021-2023 Ford F-150 | King Ranch, Lariat, Limited, Platinum, Police Responder, Raptor, SSV, Tremor, XL, XLT | 6 Cyl 2.7 L GAS, 6 Cyl 3.0 L DIESEL, 6 Cyl 3.3 L FLEX, 6 Cyl 3.5 L FULL HYBRID EV-GAS (FHEV), 6 Cyl 3.5 L GAS, 8 Cyl 5.0 L FLEX
View related parts
Ford F-150 Outer Tie Rod Part Number: PL3Z-3A130-A
$167.51 MSRP: $243.83
You Save: $76.32 (32%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: End - Spindle Rod Connecting
- Replaces: ML3Z-3A130-D
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2021-2023 Ford F-150 | Raptor, Raptor R | 6 Cyl 3.5 L GAS, 8 Cyl 5.2 L GAS
View related parts
Ford F-150 Inner Tie Rod Part Number: ML3Z-3280-C
$140.84 MSRP: $205.00
You Save: $64.16 (32%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Kit - Tie Rod
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2021-2023 Ford F-150 | Raptor, Raptor R | 6 Cyl 3.5 L GAS, 8 Cyl 5.2 L GAS
View related parts
Ford F-150 Outer Tie Rod, Driver Side Part Number: E8TZ-3304-A
Product Specifications
- Other Name: Rod Assembly - Drag Link; Drag Link Repair Kit; Outer Tie Rod End; Center Link; Tie Rod End; Drag Link
- Position: Driver Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1988-1991 Ford F-150 | Custom, XL, XLT Lariat | 6 Cyl 4.9 L GAS, 8 Cyl 5.0 L GAS, 8 Cyl 5.8 L GAS
View related parts
Ford F-150 Tie Rod End, Passenger Side Part Number: EOTZ3A131C
Product Specifications
- Other Name: End Assembly - Drag Link Rod; Outer Tie Rod
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1984-1986 Ford F-150 | Base, XL, XLT, XLT Lariat | 6 Cyl 4.9 L GAS, 6 Cyl 4.9 L LPG, 8 Cyl 5.0 L GAS, 8 Cyl 5.8 L GAS, 8 Cyl 6.9 L DIESEL
View related parts
Ford F-150 Tie Rod End, Passenger Side Part Number: EOTZ3A131E
Product Specifications
- Other Name: Steering Gear & Linkage; Outer Tie Rod
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1984-1986 Ford F-150 | Base, XL, XLT, XLT Lariat | 6 Cyl 4.9 L GAS, 6 Cyl 4.9 L LPG, 8 Cyl 5.0 L GAS, 8 Cyl 5.8 L GAS, 8 Cyl 6.9 L DIESEL
View related parts
Ford F-150 Tie Rod End, Driver Side Part Number: EOTZ3A131F
Product Specifications
- Other Name: End Spindle Rod Connector; Outer Tie Rod
- Position: Driver Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1984-1986 Ford F-150 | Base, XL, XLT, XLT Lariat | 6 Cyl 4.9 L GAS, 6 Cyl 4.9 L LPG, 8 Cyl 5.0 L GAS, 8 Cyl 5.8 L GAS, 8 Cyl 6.9 L DIESEL

| Page 1 of 2 |Next >

1-20 of 21 Results

Ford F-150 Tie Rod

OEM Tie Rod boasts unmatched quality. Each part goes through full quality checks. They adhere to Ford's official factory standards. These steps remove flaws and inconsistencies. So you can get Tie Rod with long life and a perfect fit. Come to our website and find genuine Ford F-150 parts. We keep a wide inventory of OEM F-150 parts at the highly affordable prices. It's easy to search, compare, and pick what you need. You'll love the clear info and simple checkout. We offer top-rated customer service, and we reply fast. We also ship promptly to ensure your order arrives on time.

Steering control relies on the Ford F-150 Tie Rod which operates as a crucial connection between steering gear and front wheels. Through reliable performance the Tie Rod transforms wheel movement to vehicle turns for better operational efficiency together with safety standards. Both inner and outer Tie Rod components form part of the Ford F-150 model which supports steering gear types such as rack & pinion and parallelogram systems. This universal design feature enables the product to support numerous F-150 models through its versatility which appeals to an extensive range of truck users. The pivot mechanism of the inner Tie Rod end functions differently than ball joints and delivers more stability and better handling characteristics. Preventing steering dangers requires that Tie Rod assemblies get inspected properly because detectorable wear signs can create unsafe Smooth play conditions. Produced continuously for more than seven decades the Ford F-150 pickup truck has kept its famous status as both reliable and high-performing. Design and engineering advancements keep the F-150 at the forefront of pickup ratings in the market segment. The sturdy build of the Tie Rod along with its exceptional features helps make the Ford F-150 attract vehicle owners who want reliable performance. The Ford model Tie Rod belongs to an elite category which underpins the truck's superlative reputation in the market.

Ford F-150 Tie Rod Parts and Q&A

Inner Tie Rod
9L3Z-3280-A
Q: How to service and repair the inner tie rod on Ford F-150?
A:
Service and repair operations for inner tie rod should begin by placing the vehicle in neutral position at a hoist. The tie-rod jam nut needs loosening before removing the outer tie-rod end nut that you will discard. Separate the outer tie-rod end from the wheel knuckle with the Ball Joint Tool Separator while making a note of turn counts since these values will help during reinstallation. The maintenance of the inner tie rod begins by removing both the tie-rod end and the tie-rod jam nut from the end of the rod. Discard both clamps and pull away the bellows boot from the base of the steering gear. Position the steering gear at its center and use the correct size crowfoot wrench on the rack gear flat to stop the inner tie rod from turning. Assistance may be needed for removing the right-hand side. Review all parts intended for re-use then install necessary new components. Steer the steering gear towards the center position before using the crowfoot wrench to establish the inner tie rod while tightening it to 120 Nm (89 lb-ft). Before installation of the inner tie rod apply grease to both sides of the bellows boot groove and position it correctly at the steering gear housing bead. Fit the steering gear bellows boot onto its position while using Boot Clamp Pliers to tighten a new inner bellows boot clamp securely. You must position the steering gear bellows end in the middle of the two grooves on the inner tie rod to block internal leakage before using a new outer bellows boot clamp installation. Install the tie-rod end on the inner tie rod by threading in the jam nut and repeat the same turns as initially removed. Secure the tie-rod end with the wheel knuckle but install a new tie-rod end nut then tighten it to 85 lb-ft (115 Nm). Finally adjust the front toe by tightening the tie-rod end jam nut to 103 Nm (76 lb-ft).