How to Service the Crankshaft Position Sensor on Ford Fusion?

A hoist must support the vehicle in neutral mode before starting the crankshaft position (CKP) sensor servicing. The service begins by removing four screws to set aside the RH fender splash shield followed by existing the 6 pin-type retainers and the RH splash shield assembly. Twist the crankshaft clockwise until the crankshaft pulley hole stands at the 3 o'clock mark then remove the cylinder block plug. Turn the crankshaft clockwise until it reaches the crankshaft TDC timing peg whereby the No. 1 cylinder attains top dead center (TDC) position. Then install the crankshaft TDC timing peg before continuing to turn the crankshaft until it meets the peg. Remove the bolts connecting the CKP sensor before disconnecting its electrical connector then discard the sensor. The crankshaft pulley requires 6 mm x 18 mm standard bolts to be hand-tightened to protect the front cover. The new CKP sensor installation requires the provided alignment tool to position it correctly; place both sensor bolts loosely before using the tool to adjust the CKP sensor. Finally, tighten the bolts to 7 Nm torque. Before final tightening, apply the alignment tool to adjust the CKP sensor position and follow by tightening the 2 CKP bolts to 7 Nm (62 lb-in). Connect the CKP sensor wiring while unfastening the 6 mm pulley bolt from the crankshaft and replace the block opening with a plug which should be tightened to 20 Nm (177 lb-in). In the last step reinstall the 6 pin-type retainers and the RH splash shield while using the four screws to fasten the RH fender splash shield into place.

OEM Ford Fusion Crankshaft Position Sensor

Engine Crankshaft Position Sensor

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

7 Crankshaft Position Sensors found

View related parts
Ford Fusion Crankshaft Position Sensor Part Number: BM5Z-6C315-A
$26.45 MSRP: $42.00
You Save: $15.55 (38%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Sensor - Crankshaft Position; Engine Crankshaft Position Sensor; Crankshaft Sensor; Sensor - Crankshaft Position - Cps
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2013-2020 Ford Fusion | Platinum, S, SE, SEL, Sport, Titanium | 4 Cyl 1.5 L GAS, 4 Cyl 1.6 L GAS, 4 Cyl 2.0 L GAS, 4 Cyl 2.5 L GAS, 6 Cyl 2.7 L GAS
View related parts
Ford Fusion Crankshaft Position Sensor Part Number: AA5Z-6C315-A
$47.63 MSRP: $75.64
You Save: $28.01 (38%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Sensor - Crankshaft Position; Engine Crankshaft Position Sensor; Crankshaft Sensor; Sensor - Crankshaft Position - Cps
- Manufacturer Note: Includes Attaching Bolt
- Replaces: AT4Z-6C315-A, 7T4Z-6C315-B
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2010-2016 Ford Fusion | S, SE, Sport, Titanium | 4 Cyl 1.5 L GAS, 4 Cyl 1.6 L GAS, 4 Cyl 2.0 L GAS, 4 Cyl 2.5 L GAS, 6 Cyl 3.5 L GAS
View related parts
Ford Fusion Crankshaft Position Sensor Part Number: 5L8Z-6C315-AA
$29.20 MSRP: $46.36
You Save: $17.16 (38%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Sensor - Crankshaft Position; Engine Crankshaft Position Sensor; Crankshaft Sensor; Sensor - Crankshaft Position - Cps
- Manufacturer Note: Also Used As Camshaft Position Sensor
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2006-2012 Ford Fusion | SE, SEL | 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS
View related parts
Ford Fusion Crankshaft Position Sensor Part Number: 6M8Z-6C315-AA
$67.63 MSRP: $111.27
You Save: $43.64 (40%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Sensor - Crankshaft Position; Engine Crankshaft Position Sensor; Crankshaft Sensor; Camshaft Position Sensor; Sensor - Crankshaft Position - Cps
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2013-2020 Ford Fusion | Energi Platinum, Energi SE, Energi Titanium, Platinum, Platinum Hybrid, S, S Hybrid, SE, SE Hybrid, SEL, SEL Hybrid, Sport, Titanium, Titanium Hybrid | 4 Cyl 1.5 L GAS, 4 Cyl 1.6 L GAS, 4 Cyl 2.0 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.0 L GAS, 4 Cyl 2.0 L PLUG-IN HYBRID EV-GAS (PHEV), 4 Cyl 2.5 L GAS, 6 Cyl 2.7 L GAS
View related parts
Ford Fusion Crankshaft Position Sensor Part Number: JX6Z-6C315-B
$41.12 MSRP: $64.18
You Save: $23.06 (36%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Sensor - Crankshaft Position; Engine Crankshaft Position Sensor; Crankshaft Sensor
- Replaces: AS7Z-6C315-A, DY-1461, DY-1204, JX6Z-6C315-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2013-2020 Ford Fusion | Platinum, S, SE, SEL, Sport, Titanium | 4 Cyl 1.5 L GAS, 4 Cyl 1.6 L GAS, 4 Cyl 2.0 L GAS, 4 Cyl 2.5 L GAS, 6 Cyl 2.7 L GAS
View related parts
Ford Fusion Crankshaft Position Sensor Part Number: FT4Z-6C315-C
$63.89 MSRP: $101.45
You Save: $37.56 (38%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Sensor - Crankshaft Position; Engine Crankshaft Position Sensor; Crankshaft Sensor
- Replaces: FT4Z-6C315-A, DY-1288
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2017-2020 Ford Fusion | Platinum, S, SE, SEL, Sport, Titanium | 4 Cyl 1.5 L GAS, 4 Cyl 2.0 L GAS, 4 Cyl 2.5 L GAS, 6 Cyl 2.7 L GAS
View related parts
Ford Fusion Crankshaft Position Sensor Part Number: 5M6Z-6C315-A
$110.50 MSRP: $181.82
You Save: $71.32 (40%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Sensor - Crankshaft Position; Engine Crankshaft Position Sensor; Crankshaft Sensor; Sensor - Crankshaft Position - Cps
- Replaces: 3M6Z-6C315-AA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2006-2020 Ford Fusion | Hybrid, Platinum, S, SE, SEL, Sport, Titanium | 4 Cyl 1.5 L GAS, 4 Cyl 1.6 L GAS, 4 Cyl 2.0 L GAS, 4 Cyl 2.3 L GAS, 4 Cyl 2.5 L FLEX, 4 Cyl 2.5 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.5 L GAS, 6 Cyl 2.7 L GAS

Ford Fusion Crankshaft Position Sensor

OEM Crankshaft Position Sensor boasts unmatched quality. Each part goes through full quality checks. They adhere to Ford's official factory standards. These steps remove flaws and inconsistencies. So you can get Crankshaft Position Sensor with long life and a perfect fit. Come to our website and find genuine Ford Fusion parts. We keep a wide inventory of OEM Fusion parts at the highly affordable prices. It's easy to search, compare, and pick what you need. You'll love the clear info and simple checkout. We offer top-rated customer service, and we reply fast. We also ship promptly to ensure your order arrives on time.

The Crankshaft Position Sensor is an electronic device fitted in Ford Fusion cars to identify the phase of the car's engine and sends impulses to the management system. This sensor has a major responsibility of monitoring and managing fuel injection, ignition period, and several other variables of the engine. The available Crankshaft Position Sensors are inductive, Hall Effects, magnetoresistive, and optical sensors; each of the systems has its advantages and special characteristics. Social signals of the Crankshaft Position Sensor include starting problems and other problems related to the operation of the engine that makes it vital for the well-being of the car.

Ford Fusion Crankshaft Position Sensor Parts and Q&A

Crankshaft Position Sensor
5L8Z-6C315-AA
Q: How to Service the Crankshaft Position Sensor on Ford Fusion?
A:
A hoist must support the vehicle in neutral mode before starting the crankshaft position (CKP) sensor servicing. The service begins by removing four screws to set aside the RH fender splash shield followed by existing the 6 pin-type retainers and the RH splash shield assembly. Twist the crankshaft clockwise until the crankshaft pulley hole stands at the 3 o'clock mark then remove the cylinder block plug. Turn the crankshaft clockwise until it reaches the crankshaft TDC timing peg whereby the No. 1 cylinder attains top dead center (TDC) position. Then install the crankshaft TDC timing peg before continuing to turn the crankshaft until it meets the peg. Remove the bolts connecting the CKP sensor before disconnecting its electrical connector then discard the sensor. The crankshaft pulley requires 6 mm x 18 mm standard bolts to be hand-tightened to protect the front cover. The new CKP sensor installation requires the provided alignment tool to position it correctly; place both sensor bolts loosely before using the tool to adjust the CKP sensor. Finally, tighten the bolts to 7 Nm torque. Before final tightening, apply the alignment tool to adjust the CKP sensor position and follow by tightening the 2 CKP bolts to 7 Nm (62 lb-in). Connect the CKP sensor wiring while unfastening the 6 mm pulley bolt from the crankshaft and replace the block opening with a plug which should be tightened to 20 Nm (177 lb-in). In the last step reinstall the 6 pin-type retainers and the RH splash shield while using the four screws to fasten the RH fender splash shield into place.