Question 1

How to reseal a windshield on Ford Mustang?

Accepted Answer

You should start the windshield resealing process by taking out the right-hand (RH) and left-hand (LH) windshield side garnish mouldings. Press release the pin-type retainers when working on vehicles that have convertibles. The convertibles require first removing visor clip screws then the visor trim moulding followed by screws and sun visors on both sides before disconnecting their electrical connectors. The windscreen servicing process starts by taking out the LH sun visor and its clip which requires their existing screws to be removed. Lower the front part of the headliner while supporting it with proper material. The wiper pivot arms for both LH and RH must be removed after raising them up then releasing the retainers followed by arm detachment. Remove first the cowl grille weather strip and subsequently take out the cowl grille. Apply non-alcohol based glass cleaner on both windshield glass surfaces inside and outside. The end of the urethane adhesive tip needs to be cut properly before using a high-ratio electric or battery-operated caulk gun to spread urethane while making the adhesive form uniform beads evenly across all gaps. Insert urethane adhesive to the windshield top and sides from within the car and to the bottom from outside. After tapping the windshield with a wooden applicator to check for air or water leaks, continue adhesive application if necessary. Allow the urethane adhesive to cure for at least 1 hour before testing. Installation should proceed with the cowl grille followed by the cowl grille weather strip and finally the LH and RH windshield wiper pivot arms. Coupes require headliner front repositioning before installing left and right sun visors together with their corresponding clips using screws for fixation. Convertible owners should mount LH and RH sun visors before screwing them into place while reconnecting electrical connectors. Install the visor trim moulding and visor clip screws together with the step of installing the RH and LH windshield side garnish mouldings using pin-type retainers if they apply. Adjust the wiper blade and pivot arms according to requirements.

Question 2

How to remove and replace the windshield glass on Ford Mustang?

Accepted Answer

Begin the windshield glass replacement process by putting on safety glasses combined with heavy gloves to defend against glass fragments. You should start the task by taking off both the interior rear view mirror and the cowl vent screen. Protect the pinch weld from damage while applying water lubrication to the adhesive to aid cutting work. Apply the cutting tool to the lowest windshield glass corner and proceed with adhesive removal before cleaning the pinch weld area with soft materials. After urethane adhesive curing the vehicle needs to remain parked until the time listed in the drive away chart which correlates with temperature and humidity conditions. Check the windshield glass position by dry-fitting it across the width while readjusting set blocks when present and creating alignment marks on the glass and vehicle body. Truncate the urethane after the second glass removal to produce a 1 mm to 2 mm layer on the pinch weld. The procedure for windshield replacement differs between original glass reinstallations and new glass installations which begin by removing urethane adhesive or proceeding with new moulding application starting from the top center before applying glass cleaner to clean the inside surface. Apply urethane glass primer according to manufacturer directions while allowing at least 6 minutes to dry before using adhesive and primer products with the same brand and cure-rate specifications. The specified applicator tip should be cut before applying a continuous urethane adhesive bead along the pinch weld using either an electric caulk gun with high ratio power or a battery-operated caulk gun. Mask all gaps with smooth applications of this adhesive. Open a window to maintain an even pressure inside the car while closing the door. Then install the windshield glass by aligning with the marks. Testing of the cured urethane seal should be done for air and water leaks before adding additional adhesive if needed. You must reinstall both the interior rear view mirror and the cowl vent screen as the last step.

OEM Ford Mustang Windshield

13 Windshields found

Ford Mustang Windshield Part Number: PR3Z-6303100-E

Ford Mustang Windshield, Front Part Number: YR3Z-6303100-AA

Ford Mustang Windshield, Front Part Number: FR3Z-6303100-H

Ford Mustang Windshield, Front Part Number: FR3Z-6303100-E

Ford Mustang Windshield Part Number: F5ZZ-6303100-AA

Ford Mustang Windshield, Front Part Number: XR3Z-6303100-BB

Ford Mustang Windshield Part Number: F4ZZ-7603100-A

Ford Mustang Windshield, Front Part Number: YR3Z-7603100-AA

Ford Mustang Windshield, Front Part Number: JR3Z-6303100-C

Ford Mustang Windshield, Front Part Number: FR3Z-6303100-J

Ford Mustang Windshield, Front Part Number: 4R3Z-6303100-AA

Ford Mustang Windshield, Front Part Number: XR3Z-7603100-CC

Ford Mustang Windshield Part Number: PR3Z-6303100-B

Ford Mustang Windshield

Ford Mustang Windshield Parts and Q&A

Related Ford Mustang Parts

Browse Ford Mustang Windshield by Years