How to remove and install the engine mount on Lincoln MKX?

The procedure for engine mount removal requires positioning the vehicle on a hoist with NEUTRAL gear selection. First disconnect the 2 exhaust hangers followed by loosening the exhaust flexible pipe clamp to remove all components including 4 nuts, the exhaust flexible pipe assembly, the Y-pipe from the vehicle as a single unit. Replace the nuts with new ones along with discarding the gasket. First remove the two nuts that secure the roll restrictor heat shield before loosening the roll restrictor-to-subframe through bolt. First, extract the through bolt from the roll restrictor through bolt and then separate the 2 roll restrictor bracket plate bolts before removing the 3 bolts of the transaxle bracket. When setting up the Oil Pan Holding Fixture users need to carefully match it with the mounting bosses at the oil pan before placing it under the pan near a floor jack. First remove the 3 bolts from the engine coolant degas bottle and place it to the side before proceeding with the nut and bolt removal of the engine mount brace. Begin engine mount removal by extracting first the 4 engine mount nuts and after that the 3 engine mount bolts. To install the engine mount begin with its placement and secure it through tightening the 3 bolts to 90 Nm (66 lb-ft). Begin by installing the 4 engine mount nuts while applying a torque of 63 Nm (46 lb-ft) and afterward tighten the engine mount brace along with its nut and bolt at 20 Nm (177 lb-in). Put the engine coolant degas bottle into position before securing it with the 3 bolts which must be tightened to 9 Nm (80 lb-in). First securely fasten the transaxle bracket through its 3 bolts to 90 Nm (66 lb-ft). Proceed with engine roll restrictor and transaxle bracket installation along with 3 bolts which require torquing to 90 Nm (66 lb-ft). Fasten the roll restrictor-to-subframe through bolt to 103 Nm (76 lb-ft) before installing the roll restrictor heat shield and tightening its 2 nuts to 11 Nm (97 lb-in). The Y-pipe assembly installation requires a new gasket before positioning the assembly and securing it with 4 new nuts that you should tighten to 40 Nm (30 lb-ft). Then install the 2 exhaust hangers before clamping the exhaust to 40 Nm (30 lb-ft).

OEM Lincoln MKX Engine Mount

Engine Motor Mount

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

13 Engine Mounts found

View related parts
Lincoln MKX Transmission Mount
Part Number: 8T4Z-6068-B
$61.99 MSRP: $76.67
You Save: $14.68 (20%)
ADD TO CART
Product Specifications
- Other Name: Housing; Transfer Case Mount
- Replaces: 8T4Z-6068-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2008-2010 Lincoln MKX | Base | 6 Cyl 3.5 L GAS
View related parts
Lincoln MKX Transmission Mount
Part Number: BT4Z-6068-A
$59.56 MSRP: $91.48
You Save: $31.92 (35%)
ADD TO CART
Product Specifications
- Other Name: Housing; Transfer Case Mount
- Replaced by: DT4Z-6031-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2011-2013 Lincoln MKX | Base | 6 Cyl 3.7 L GAS
View related parts
Lincoln MKX Transmission Mount
Part Number: DT4Z-6068-A
$61.54 MSRP: $89.58
You Save: $28.04 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Housing; Engine Torque Strut; Engine Mount Torque Strut; Transfer Case Mount; Torque Arm
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2011-2015 Lincoln MKX | Base | 6 Cyl 3.7 L GAS
View related parts
Lincoln MKX Transmission Mount Bracket, Driver Side
Part Number: DT4Z-6031-A
$59.56 MSRP: $91.48
You Save: $31.92 (35%)
ADD TO CART
Product Specifications
- Other Name: Bracket - Engine Mounting; Automatic Transmission Mount Bracket; Transfer Case Mount; Transmission Mount
- Manufacturer Note: INSULATOR
- Position: Driver Side
- Replaces: 7T4Z-6031-AA, 8T4Z-6031-B, BT4Z-6068-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2011-2015 Lincoln MKX | Base | 6 Cyl 3.7 L GAS
View related parts
Lincoln MKX Motor Mount, Front
Part Number: DP5Z-6038-B
$121.37 MSRP: $176.67
You Save: $55.30 (32%)
ADD TO CART
Product Specifications
- Other Name: Bracket - Engine Front Support; Engine Mount, Front; Engine Mount Bracket; Front Mount; Mount
- Position: Front
- Replaces: DP5Z-6038-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2016-2018 Lincoln MKX | Black Label, Premiere, Reserve, Select | 6 Cyl 3.7 L GAS
View related parts
Lincoln MKX Transmission Mount
Part Number: 8T4Z-6068-A
$53.59 MSRP: $76.67
You Save: $23.08 (31%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Housing; Transfer Case Mount
- Replaced by: 8T4Z-6068-B
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2007-2008 Lincoln MKX | Base | 6 Cyl 3.5 L GAS
View related parts
Lincoln MKX Motor Mount, Passenger Side
Part Number: 8T4Z-6038-A
$128.24 MSRP: $186.67
You Save: $58.43 (32%)
ADD TO CART
Product Specifications
- Other Name: Bracket - Insulator Mounting; Engine Mount, Right; Engine Mount Bracket; Front Mount; Mount
- Manufacturer Note: Bracket And Insulator
- Position: Passenger Side
- Replaces: 7T4Z-6038-AA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2007-2015 Lincoln MKX | Base | 6 Cyl 3.5 L GAS, 6 Cyl 3.7 L GAS
View related parts
Lincoln MKX Transmission Mount, Driver Side
Part Number: 7A1Z-6038-AA
$86.65 MSRP: $126.13
You Save: $39.48 (32%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Insulator Assembly; Automatic Transmission Mount, Left; Engine Mount Bracket; Transfer Case Mount; Motor Mount; Front Mount; Mount
- Manufacturer Note: INSULATOR
- Position: Driver Side
- Replaces: 7T4Z-6038-AD
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2007-2015 Lincoln MKX | Base | 6 Cyl 3.5 L GAS, 6 Cyl 3.7 L GAS
View related parts
Lincoln MKX Mount Bracket, Front Passenger Side
Part Number: 8M8Z-6038-A
$63.73 MSRP: $97.90
You Save: $34.17 (35%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bracket - Engine Mounting; Front Engine Mount Support; Right Engine Mount Bracket; Torque Strut; Motor Mount.; Engine Bracket; Front Mount; Front Mount Bracket; Support; Mount
- Manufacturer Note: Bracket
- Position: Front Passenger Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2007-2010 Lincoln MKX | Base | 6 Cyl 3.5 L GAS
View related parts
Lincoln MKX Bracket
Part Number: F2GZ-6038-C
$46.65 MSRP: $69.85
You Save: $23.20 (34%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Bracket - Engine Mounting; Engine Mount Bracket; Transmission Mount; Motor Mount
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2016-2018 Lincoln MKX | Black Label, Premiere, Reserve, Select | 6 Cyl 2.7 L GAS
View related parts
Lincoln MKX Engine Bracket, Driver Side
Part Number: 8T4Z-6031-B
$59.56 MSRP: $91.48
You Save: $31.92 (35%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Bracket - Engine Mount; Engine Mount Bracket, Left; Motor Mount; Bracket - Engine Mounting
- Manufacturer Note: INSULATOR
- Position: Driver Side
- Replaced by: DT4Z-6031-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2007-2010 Lincoln MKX | Base | 6 Cyl 3.5 L GAS
View related parts
Lincoln MKX Motor Mount
Part Number: F2GZ-6038-A
$201.27 MSRP: $313.50
You Save: $112.23 (36%)
ADD TO CART
Product Specifications
- Other Name: Bracket - Engine Front Support; Engine Mount; Engine Mount Bracket; Mount
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2016-2018 Lincoln MKX | Black Label, Premiere, Reserve, Select | 6 Cyl 2.7 L GAS
View related parts
Lincoln MKX Support Bracket
Part Number: DP5Z-6F055-A
$30.35 MSRP: $44.18
You Save: $13.83 (32%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bracket; Engine Torque Strut; Support Rod; Mount; Transfer Case; Transmission; Motor; Transmission Mount Bracket; Torque Arm Bracket; Torque Strut Support Bracket; Torque Strut Bracket; Upper Arm Bracket
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2016-2018 Lincoln MKX | Black Label, Premiere, Reserve, Select | 6 Cyl 2.7 L GAS, 6 Cyl 3.7 L GAS

Lincoln MKX Engine Mount

Welcome to our website where you can discover high-quality, genuine Lincoln MKX Engine Mount. We offer an extensive inventory of OEM Lincoln MKX Engine Mount at affordable prices. We are committed to providing top-rated customer service along with prompt delivery.

Lincoln MKX Engine Mount Parts Questions & Experts Answers

Transmission Mount, Driver Side
7A1Z-6038-AA
Q: How to remove and install the engine mount on Lincoln MKX?
A: The procedure for engine mount removal requires positioning the vehicle on a hoist with NEUTRAL gear selection. First disconnect the 2 exhaust hangers followed by loosening the exhaust flexible pipe clamp to remove all components including 4 nuts, the exhaust flexible pipe assembly, the Y-pipe from the vehicle as a single unit. Replace the nuts with new ones along with discarding the gasket. First remove the two nuts that secure the roll restrictor heat shield before loosening the roll restrictor-to-subframe through bolt. First, extract the through bolt from the roll restrictor through bolt and then separate the 2 roll restrictor bracket plate bolts before removing the 3 bolts of the transaxle bracket. When setting up the Oil Pan Holding Fixture users need to carefully match it with the mounting bosses at the oil pan before placing it under the pan near a floor jack. First remove the 3 bolts from the engine coolant degas bottle and place it to the side before proceeding with the nut and bolt removal of the engine mount brace. Begin engine mount removal by extracting first the 4 engine mount nuts and after that the 3 engine mount bolts. To install the engine mount begin with its placement and secure it through tightening the 3 bolts to 90 Nm (66 lb-ft). Begin by installing the 4 engine mount nuts while applying a torque of 63 Nm (46 lb-ft) and afterward tighten the engine mount brace along with its nut and bolt at 20 Nm (177 lb-in). Put the engine coolant degas bottle into position before securing it with the 3 bolts which must be tightened to 9 Nm (80 lb-in). First securely fasten the transaxle bracket through its 3 bolts to 90 Nm (66 lb-ft). Proceed with engine roll restrictor and transaxle bracket installation along with 3 bolts which require torquing to 90 Nm (66 lb-ft). Fasten the roll restrictor-to-subframe through bolt to 103 Nm (76 lb-ft) before installing the roll restrictor heat shield and tightening its 2 nuts to 11 Nm (97 lb-in). The Y-pipe assembly installation requires a new gasket before positioning the assembly and securing it with 4 new nuts that you should tighten to 40 Nm (30 lb-ft). Then install the 2 exhaust hangers before clamping the exhaust to 40 Nm (30 lb-ft).