How to Service and Repair the Rear Motor and Transmission Mount on Lincoln MKZ?

Start transaxle rear support insulator service and repair by hoisting the vehicle in neutral and then removing its splash shield bolts while you also detach the shield before reinstalling all bolts with 47 Nm (35 ft. lbs.) torque. Start by removing the 2 bolts at the bottom of the transaxle rear support insulator while torquing them to 63 Nm (46 ft. lbs.) when reinstalling. You should lower the vehicle while following these steps to remove the battery and battery tray. Begin by disconnecting the positive battery cable retainer then remove the battery tray nut and bolt while tightening the bolt to 9 Nm (80 inch lbs.). The power distribution box can be placed aside after removing its 2 bolts and nut and pulling it upward to unclip the pushpin and disconnecting the 2 electrical connectors. To support the transaxle along with a suitable floor jack you must unscrew the four remaining bolts from the transaxle rear support insulator. Install new mount studs properly into their designated case seats followed by bolt tightening to 63 Nm (46 ft. lbs.) torque. First disconnect the clutch hydraulic line spring clip while continuing to lower the clutch line until it leaves the bracket. Then take off the clutch hydraulic line plastic retainer and transaxle mount. The installation process will be completed by performing the opposite steps of removal.

OEM Lincoln MKZ Motor And Transmission Mount

Motor and Trans Mount

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

28 Motor And Transmission Mounts found

View related parts
Lincoln MKZ Transmission Mount, Lower Part Number: DP5Z-6068-A
$55.42 MSRP: $80.67
You Save: $25.25 (32%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Automatic Transmission Mount, Lower; Engine Torque Strut; Transfer Case Mount; Motor Mount; Torque Arm; Torque Strut; Mount
- Position: Lower
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2013-2020 Lincoln MKZ | Base, Black Label, Black Label Hybrid, Hybrid, Premiere, Premiere Hybrid, Reserve, Reserve Hybrid, Reserve I, Reserve I Hybrid, Reserve II, Reserve II Hybrid, Select, Select Hybrid | 4 Cyl 2.0 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.0 L GAS
View related parts
Lincoln MKZ Torque Strut Part Number: 9E5Z-6068-A
$91.69 MSRP: $133.47
You Save: $41.78 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Housing; Engine Torque Strut; Engine Mount Torque Strut; Engine Mount Bracket; Motor Mount; Strut
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2011-2012 Lincoln MKZ | Hybrid | 4 Cyl 2.5 L FULL HYBRID EV-GAS (FHEV)
View related parts
Lincoln MKZ Transmission Mount, Lower Part Number: 8H6Z-6068-A
$63.89 MSRP: $93.00
You Save: $29.11 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Housing; Engine Support Rod, Lower; Engine Mount Torque Strut; Engine Mount Bracket; Transfer Case Mount; Motor Mount; Torque Arm; Torque Strut; Strut
- Position: Lower
- Replaces: 7H6Z-6068-CA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2007-2012 Lincoln MKZ | Base, High Version - Car, Hybrid, Low Version - Car, Mid Version - Car, Sport | 3.5L V6, 6 Cyl 3.5 L GAS
View related parts
Lincoln MKZ Front Mount Part Number: 9E5Z-6038-C
$60.11 MSRP: $87.50
You Save: $27.39 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Bracket - Engine Front Support; Engine Mount, Front; Engine Mount Bracket; Motor Mount; Mount
- Position: Front
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2011-2012 Lincoln MKZ | Hybrid | 4 Cyl 2.5 L FULL HYBRID EV-GAS (FHEV)
View related parts
Lincoln MKZ Transmission Mount, Upper Part Number: 8H6Z-6038-A
$83.62 MSRP: $121.72
You Save: $38.10 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Insulator Assembly; Automatic Transmission Mount, Upper; Transfer Case Mount
- Position: Upper
- Replaces: 7H6Z-6038-AB
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2007-2012 Lincoln MKZ | Base, High Version - Car, Hybrid, Low Version - Car, Mid Version - Car, Sport | 3.5L V6, 6 Cyl 3.5 L GAS
View related parts
Lincoln MKZ Front Mount Part Number: DG9Z-6038-J
$108.20 MSRP: $157.50
You Save: $49.30 (32%)
ADD TO CART
Product Specifications
- Other Name: Bracket - Engine Front Support; Engine Mount, Front; Automatic Transmission Mount; Engine Mount Bracket; Motor Mount; Mount
- Position: Front
- Replaces: DG9Z-6038-C
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2013-2016 Lincoln MKZ | Base, Black Label, HYBRID SELECT VERSION, Reserve Version, SE Wagon, Series 25 | 2.0L L4, 4 Cyl 2.0 L GAS
View related parts
Lincoln MKZ Transmission Mount, Lower Part Number: DP5Z-6068-H
$113.72 MSRP: $175.00
You Save: $61.28 (36%)
ADD TO CART
Product Specifications
- Other Name: Automatic Transmission Mount, Lower; Engine Torque Strut; Transfer Case Mount; Motor Mount; Torque Arm; Lower Trans Mount; Torsion Damper
- Position: Lower
- Replaces: DP5Z-6068-B, DP5Z-6068-G
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2013-2016 Lincoln MKZ | Base, Black Label, HYBRID SELECT VERSION, Reserve Version, SE Wagon, Series 25 | 3.7L V6, 6 Cyl 3.7 L GAS
View related parts
Lincoln MKZ Motor Mount, Front Part Number: DP5Z-6038-B
$167.17 MSRP: $243.33
You Save: $76.16 (32%)
ADD TO CART
Product Specifications
- Other Name: Bracket - Engine Front Support; Engine Mount, Front; Engine Mount Bracket; Front Mount; Mount
- Position: Front
- Replaces: DP5Z-6038-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2013-2016 Lincoln MKZ | Base, Black Label, HYBRID SELECT VERSION, Reserve Version, SE Wagon, Series 25 | 3.7L V6, 6 Cyl 3.7 L GAS
View related parts
Lincoln MKZ Trans Mount Bracket Damper, Upper Part Number: DG9Z-6F028-D
$40.88 MSRP: $58.48
You Save: $17.60 (31%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Damper Assembly; Automatic Transmission Mount Insulator; Engine Mount Isolator, Upper; Transfer Case Mount; Motor Mount; Damper; Transmission Mount
- Position: Upper
- Replaces: DG9Z-6F028-B, DG9Z-6F028-C
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2013-2016 Lincoln MKZ | Base, Black Label, HYBRID SELECT VERSION, Reserve Version, SE Wagon, Series 25 | 2.0L L4, 4 Cyl 2.0 L GAS
View related parts
Lincoln MKZ Front Mount Part Number: DG9Z-6038-L
$106.83 MSRP: $155.50
You Save: $48.67 (32%)
ADD TO CART
Product Specifications
- Other Name: Bracket - Engine Front Support; Engine Mount, Front; Engine Mount Bracket; Motor Mount; Mount
- Position: Front
- Replaces: DG9Z-6038-A, DG9Z-6038-F, DG9Z-6038-G
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2013-2020 Lincoln MKZ | Black Label Hybrid, Hybrid, HYBRID SELECT VERSION, Premiere Hybrid, Reserve Hybrid, Reserve I Hybrid, Reserve II Hybrid, Reserve Version, SE Wagon, Select Hybrid, Series 25 | 2.0L L4, 4 Cyl 2.0 L FULL HYBRID EV-GAS (FHEV)
View related parts
Lincoln MKZ Support Bracket Part Number: DP5Z-6F055-A
$30.35 MSRP: $44.18
You Save: $13.83 (32%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bracket; Engine Torque Strut; Support Rod; Mount; Transfer Case; Transmission; Motor
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2017-2020 Lincoln MKZ | Black Label, Reserve, Reserve II, Select | 6 Cyl 3.0 L GAS
View related parts
Lincoln MKZ Support Bracket Part Number: JG9Z-6E042-C
$67.13 MSRP: $97.72
You Save: $30.59 (32%)
ADD TO CART
Product Specifications
- Other Name: Bracket; Engine Mount Support Bracket; Engine Mount Bracket; Motor Mount
- Replaces: DG9Z-6E042-A, DG9Z-6E042-C, HG9Z-6E042-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2013-2020 Lincoln MKZ | Base, Black Label, HYBRID SELECT VERSION, Premiere, Reserve, Reserve I, Reserve II, Reserve Version, SE Wagon, Select, Series 25 | 2.0L L4, 4 Cyl 2.0 L GAS
View related parts
Lincoln MKZ Support Bracket Part Number: DG9Z-6E042-B
$94.81 MSRP: $138.00
You Save: $43.19 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Bracket; Engine Mount Support Bracket; Engine Mount Bracket; Motor Mount
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2013-2020 Lincoln MKZ | Black Label Hybrid, Hybrid, Premiere Hybrid, Reserve Hybrid, Reserve I Hybrid, Reserve II Hybrid, Select Hybrid | 4 Cyl 2.0 L FULL HYBRID EV-GAS (FHEV)
View related parts
Lincoln MKZ Transmission Mount, Upper Part Number: DP5Z-6068-C
$108.29 MSRP: $166.65
You Save: $58.36 (36%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Housing; Engine Torque Strut; Engine Support Rod; Engine Mount Torque Strut; Transfer Case Mount; Motor Mount; Torque Arm; Torque Strut
- Position: Upper
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2013-2016 Lincoln MKZ | Base, Black Label | 6 Cyl 3.7 L GAS
View related parts
Lincoln MKZ Transmission Mount, Upper Part Number: GD9Z-6068-H
$101.33 MSRP: $147.50
You Save: $46.17 (32%)
ADD TO CART
Product Specifications
- Other Name: Housing - Transmission Extension; Automatic Transmission Mount, Upper; Transfer Case Mount; Upper Trans Mount
- Position: Upper
- Replaces: DP5Z-6068-E, GD9Z-6068-G
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2013-2016 Lincoln MKZ | Base, Black Label, HYBRID SELECT VERSION, Reserve Version, SE Wagon, Series 25 | 3.7L V6, 6 Cyl 3.7 L GAS
View related parts
Lincoln MKZ Transmission Mount, Upper Part Number: DG9Z-6068-S
$148.62 MSRP: $216.33
You Save: $67.71 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Housing - Transmission Extension; Manual Transmission Mount, Upper; Engine Mount Bracket; Motor Mount; Upper Mount
- Position: Upper
- Replaces: DG9Z-6068-P, DG9Z-6068-K, DG9Z-6068-M
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2013-2020 Lincoln MKZ | Black Label Hybrid, Hybrid, HYBRID SELECT VERSION, Premiere Hybrid, Reserve Hybrid, Reserve I Hybrid, Reserve II Hybrid, Reserve Version, SE Wagon, Select Hybrid, Series 25 | 2.0L L4, 4 Cyl 2.0 L FULL HYBRID EV-GAS (FHEV)
View related parts
Lincoln MKZ Front Mount Part Number: HG9Z-6038-A
$153.43 MSRP: $223.33
You Save: $69.90 (32%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Bracket - Engine Front Support; Engine Mount, Front; Engine Mount Bracket; Motor Mount; Mount
- Position: Front
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2017-2020 Lincoln MKZ | Base, Black Label, Premiere, Reserve, Reserve I, Reserve II, Select | 4 Cyl 2.0 L GAS
View related parts
Lincoln MKZ Upper Arm Part Number: F2GZ-6068-B
$104.77 MSRP: $152.50
You Save: $47.73 (32%)
Product Specifications
- Other Name: Automatic Transmission Mount; Engine Torque Strut; Engine Support Rod; Transfer Case Mount; Motor Mount.; Transmission Mount; Torque Strut
- Position: Upper
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2017-2020 Lincoln MKZ | Black Label, Reserve, Reserve II, Select | 6 Cyl 3.0 L GAS
View related parts
Lincoln MKZ Transmission Mount Part Number: BE5Z-6038-C
$115.65 MSRP: $168.33
You Save: $52.68 (32%)
Product Specifications
- Other Name: Insulator Assembly; Automatic Transmission Mount; Transfer Case Mount
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2011-2012 Lincoln MKZ | Hybrid | 4 Cyl 2.5 L FULL HYBRID EV-GAS (FHEV)
View related parts
Lincoln MKZ Front Mount Part Number: 7H6Z-6038-A
$141.98 MSRP: $206.67
You Save: $64.69 (32%)
Product Specifications
- Other Name: Bracket; Engine Mount; Engine Mount Bracket; Motor Mount; Mount
- Position: Front
- Replaces: 7H6Z-6038-AA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2007-2012 Lincoln MKZ | Base, High Version - Car, Hybrid, Low Version - Car, Mid Version - Car, Sport | 3.5L V6, 6 Cyl 3.5 L GAS

| Page 1 of 2 |Next >

1-20 of 28 Results

Lincoln MKZ Motor And Transmission Mount

OEM Motor And Transmission Mount boasts unmatched quality. Each part goes through full quality checks. They adhere to Lincoln's official factory standards. These steps remove flaws and inconsistencies. So you can get Motor And Transmission Mount with long life and a perfect fit. Come to our website and find genuine Lincoln MKZ parts. We keep a wide inventory of OEM MKZ parts at the highly affordable prices. It's easy to search, compare, and pick what you need. You'll love the clear info and simple checkout. We offer top-rated customer service, and we reply fast. We also ship promptly to ensure your order arrives on time.

The Motor And Transmission Mount is an essential and vital part that speaks of the reliability of the entire assembly of the Lincoln MKZ series. Acting as a stable platform for the transmission system, this Motor And Transmission Mount ensures that the transmission stays put in its position and, at the same time, insulates the same from vibrations emanating from the engine. This is especially crucial in as far as it supports stability and structural performance of the Lincoln MKZ as it cushions them during operation. Designed to fit most MKZ models, Motor And Transmission Mount effectively helps to improve the vehicle's performance and endurance and therefore is significant to the driving experience. The Lincoln MKZ which is a luxury vehicle with practicality get to enjoy this component by enhancing efficiency and safety in order come up with well controlled ride. Convenience of the Motor And Transmission Mount is based on its location and provides great balance and protection of the transmission; all this contributes to the increase in popularity of the MKZ car model. Being first launched in 2007, Lincoln MKZ has been continually improving its traits and Motor And Transmission Mount is one of them. That's why the Lincoln MKZ can boast of a combination of luxury, performance, and reliability thanks to the Lincoln's commitment to the top quality Motor And Transmission Mount.

Lincoln MKZ Motor And Transmission Mount Parts and Q&A

Transmission Mount, Upper
8H6Z-6038-A
Q: How to Service and Repair the Rear Motor and Transmission Mount on Lincoln MKZ?
A:
Start transaxle rear support insulator service and repair by hoisting the vehicle in neutral and then removing its splash shield bolts while you also detach the shield before reinstalling all bolts with 47 Nm (35 ft. lbs.) torque. Start by removing the 2 bolts at the bottom of the transaxle rear support insulator while torquing them to 63 Nm (46 ft. lbs.) when reinstalling. You should lower the vehicle while following these steps to remove the battery and battery tray. Begin by disconnecting the positive battery cable retainer then remove the battery tray nut and bolt while tightening the bolt to 9 Nm (80 inch lbs.). The power distribution box can be placed aside after removing its 2 bolts and nut and pulling it upward to unclip the pushpin and disconnecting the 2 electrical connectors. To support the transaxle along with a suitable floor jack you must unscrew the four remaining bolts from the transaxle rear support insulator. Install new mount studs properly into their designated case seats followed by bolt tightening to 63 Nm (46 ft. lbs.) torque. First disconnect the clutch hydraulic line spring clip while continuing to lower the clutch line until it leaves the bracket. Then take off the clutch hydraulic line plastic retainer and transaxle mount. The installation process will be completed by performing the opposite steps of removal.