How to remove and replace the Door Lock Actuator for the right-hand drive assembly on Mercury Monterey?

The procedure for right-hand drive assembly actuator power sliding door motor replacement begins with opening both power sliding door and rear quarter window access points. Begin replacing the power sliding door motor by first removing the SJB fuse 11 with its 5A rating as well as the rear quarter trim panel. The first task involves removing the five drive assembly actuator pulley cable bolts followed by extracting the power sliding door center track moulding. Operating the power sliding door drive assembly actuator without cable connection will lead to damage so operatives must avoid using it. The power sliding door requires an opening space of 100 mm (4 in) against the B-pillar before extracting the front cable clip while removing the front cable. To detach the rear cable clip the door should be opened halfway before removing the rear cable. Fiber cables need to pass through the vehicle chamber before disconnection of power sliding door module electrical connectors followed by motor assembly bolt removal for complete motor extraction. The module needs to be smoothly detached from the drive assembly. Begin by installing the power sliding door module before adding the motor assembly which should be tightened to 11 Nm (8 lb-ft) using four bolts. The power sliding door module electrical connectors should be connected after checking that cables maintain distance from sheet metal and after they are fully fed through the opening. Before closing the power sliding door use it to attach the rear cable through its installed clip by positioning it tightly on the stud. After opening the power sliding door to 101.6 mm (4 in) distance from the B-pillar position install the front cable by applying its provided clip. Finnish the installation of the power sliding door center track moulding along with the five drive assembly actuator pulley cable bolts by tightening them to 11 Nm (8 lb-ft). The last step involves reinstallation of SJB fuse 11 (5A) followed by power sliding door initialization and installment of the rear quarter trim panel.

How to Service the Front Door Lock Actuator on Mercury Monterey?

The service of front door lock actuators begins with removing the front door trim. The next step requires removing the three front door latch bolts followed by torquing them to 9 Nm (80 lb-in) before reinstalling them properly. Disconnect the exterior front door handle actuating rod while also disconnecting any present door lock cylinder actuating rod. Use the front door latch to reach the door lock actuator before detaching its electrical connector. Complete the door lock actuator removal process by proceeding to install it onto the front door latch while following the reverse steps of removal.

OEM Mercury Monterey Door Lock Actuator

Power Door Lock Actuator

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

11 Door Lock Actuators found

View related parts
Mercury Monterey Lock Actuator, Front Passenger Side Part Number: 6L3Z-25218A42-AA
$67.29 MSRP: $110.73
You Save: $43.44 (40%)
Ships in 1 Business Day
ADD TO CART
Product Specifications
- Other Name: Actuator Assembly; Door Lock Motor, Front/Rear Right; Tailgate/Trunk Lock Motor; Door Lock Solenoid
- Position: Passenger Side
- Replaces: F88Z-16219A64-BB
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2004-2007 Mercury Monterey | Base, Convenience, Luxury, Premier | 6 Cyl 4.2 L GAS
View related parts
Mercury Monterey Lock Actuator, Front Driver Side Part Number: 6L3Z-25218A43-AA
$46.14 MSRP: $73.27
You Save: $27.13 (38%)
Ships in 1 Business Day
ADD TO CART
Product Specifications
- Other Name: Actuator Assembly; Door Lock Actuator Motor, Front Left; Tailgate Lock Actuator; Trunk Lock Actuator; Door Lock Solenoid
- Position: Driver Side
- Replaces: 3L3Z-25218A43-AA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2004-2007 Mercury Monterey | Base, Convenience, Limited, Luxury, Mercury Convenience, Mercury Luxury, Mercury Premier, Premier, SE, SEL, SES | 3.9L V6, 4.2L V6, 6 Cyl 4.2 L GAS
View related parts
Mercury Monterey Actuator, Driver Side Part Number: 7F2Z-17218A43-AA
$78.10 MSRP: $108.04
You Save: $29.94 (28%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Actuator Assembly; Door Lock Actuator Motor; Door Lock Actuator
- Position: Driver Side
- Replaces: 5F2Z-17218A43-AA, 6F2Z-17218A43-AA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2005-2007 Mercury Monterey | Base, Convenience, Limited, Luxury, Mercury Convenience, Mercury Luxury, Mercury Premier, Premier, SE, SEL, SES | 3.9L V6, 4.2L V6, 6 Cyl 4.2 L GAS
View related parts
Mercury Monterey Latch Assembly, Passenger Side Part Number: 7F2Z-17264A00-C
$502.91 MSRP: $690.00
You Save: $187.09 (28%)
ADD TO CART
Product Specifications
- Other Name: Remote Control System; Sliding Door Latch, Right; Door Latch Assembly; Door Lock
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2006-2007 Mercury Monterey | Luxury | 6 Cyl 4.2 L GAS
View related parts
Mercury Monterey Latch Assembly, Passenger Side Part Number: 5F2Z-17264A00-B
$151.08 MSRP: $205.59
You Save: $54.51 (27%)
ADD TO CART
Product Specifications
- Other Name: Remote Control System; Sliding Door Latch, Right; Door Latch Assembly; Door Lock; Lock
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2004-2005 Mercury Monterey | Base, Convenience, Luxury, Premier | 6 Cyl 4.2 L GAS
View related parts
Mercury Monterey Actuator, Passenger Side Part Number: 7F2Z-17218A42-AA
Product Specifications
- Other Name: Actuator Assembly; Door Lock Actuator Motor; Door Lock Actuator
- Position: Passenger Side
- Replaces: 6F2Z-17218A42-AA, 5F2Z-17218A42-AA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2005-2007 Mercury Monterey | Base, Convenience, Limited, Luxury, Mercury Convenience, Mercury Luxury, Mercury Premier, Premier, SE, SEL, SES | 3.9L V6, 4.2L V6, 6 Cyl 4.2 L GAS
View related parts
Mercury Monterey Lock Actuator, Rear Part Number: 4C2Z-16218A42-CA
Product Specifications
- Other Name: Actuator Assembly; Door Lock Actuator Motor, Center, Rear, Rear Rearward; Liftgate Actuator
- Position: Rear
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2005-2007 Mercury Monterey | Convenience, Luxury, Premier | 6 Cyl 4.2 L GAS
View related parts
Mercury Monterey Actuator Part Number: 3F2Z-14S411-AA
Product Specifications
- Other Name: Wire Assembly; Door Lock Actuator Motor; Door Lock Actuator
- Replaces: 4F2Z-17264A00-DB, 5F2Z-17264A00-BA, 1F2Z-17264A01-BA, 1F2Z-16264A00-BA, 4F2Z-17264A00-DA, 4F2Z-17218A42-BA, 5F2Z-17264A01-BA, XF2Z-16218A42-DA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2004-2005 Mercury Monterey | Base, Convenience, Limited, Luxury, Mercury Convenience, Mercury Luxury, Mercury Premier, Premier, SE, SEL, SES | 3.9L V6, 4.2L V6, 6 Cyl 4.2 L GAS
View related parts
Mercury Monterey Lock Actuator, Front Center Part Number: 2F2Z-16218A42-BA
Product Specifications
- Other Name: Actuator Assembly; Door Lock Motor, Center Front, Rear; Tailgate Lock Motor; Solenoid; Liftgate Actuator
- Position: Front Center
- Replaces: F3VY-54218A42-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2004 Mercury Monterey | Base, Limited, Mercury Convenience, Mercury Luxury, Mercury Premier, Premier, SE, SEL, SES | 3.9L V6, 4.2L V6, 6 Cyl 4.2 L GAS
View related parts
Mercury Monterey Latch Assembly, Driver Side Part Number: 7F2Z-17264A01-C
Product Specifications
- Other Name: Remote Control System; Sliding Door Latch, Left; Door Latch Assembly; Door Lock
- Position: Driver Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2006-2007 Mercury Monterey | Luxury | 6 Cyl 4.2 L GAS
View related parts
Mercury Monterey Latch Assembly, Driver Side Part Number: 5F2Z-17264A01-B
Product Specifications
- Other Name: Remote Control System; Sliding Door Latch, Left; Door Latch Assembly; Door Lock
- Position: Driver Side
- Replaces: 5F2Z-17264A01-AB, 5F2Z-17264A01-AA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2004-2005 Mercury Monterey | Base, Convenience, Limited, Luxury, Mercury Convenience, Mercury Luxury, Mercury Premier, Premier, SE, SEL, SES | 3.9L V6, 4.2L V6, 6 Cyl 4.2 L GAS

Mercury Monterey Door Lock Actuator

OEM Door Lock Actuator boasts unmatched quality. Each part goes through full quality checks. They adhere to Mercury's official factory standards. These steps remove flaws and inconsistencies. So you can get Door Lock Actuator with long life and a perfect fit. Come to our website and find genuine Mercury Monterey parts. We keep a wide inventory of OEM Monterey parts at the highly affordable prices. It's easy to search, compare, and pick what you need. You'll love the clear info and simple checkout. We offer top-rated customer service, and we reply fast. We also ship promptly to ensure your order arrives on time.

Mercury Monterey Door Lock Actuator Parts and Q&A

Lock Actuator, Rear
4C2Z-16218A42-CA
Q: How to remove and replace the Door Lock Actuator for the right-hand drive assembly on Mercury Monterey?
A:
The procedure for right-hand drive assembly actuator power sliding door motor replacement begins with opening both power sliding door and rear quarter window access points. Begin replacing the power sliding door motor by first removing the SJB fuse 11 with its 5A rating as well as the rear quarter trim panel. The first task involves removing the five drive assembly actuator pulley cable bolts followed by extracting the power sliding door center track moulding. Operating the power sliding door drive assembly actuator without cable connection will lead to damage so operatives must avoid using it. The power sliding door requires an opening space of 100 mm (4 in) against the B-pillar before extracting the front cable clip while removing the front cable. To detach the rear cable clip the door should be opened halfway before removing the rear cable. Fiber cables need to pass through the vehicle chamber before disconnection of power sliding door module electrical connectors followed by motor assembly bolt removal for complete motor extraction. The module needs to be smoothly detached from the drive assembly. Begin by installing the power sliding door module before adding the motor assembly which should be tightened to 11 Nm (8 lb-ft) using four bolts. The power sliding door module electrical connectors should be connected after checking that cables maintain distance from sheet metal and after they are fully fed through the opening. Before closing the power sliding door use it to attach the rear cable through its installed clip by positioning it tightly on the stud. After opening the power sliding door to 101.6 mm (4 in) distance from the B-pillar position install the front cable by applying its provided clip. Finnish the installation of the power sliding door center track moulding along with the five drive assembly actuator pulley cable bolts by tightening them to 11 Nm (8 lb-ft). The last step involves reinstallation of SJB fuse 11 (5A) followed by power sliding door initialization and installment of the rear quarter trim panel.
Lock Actuator, Front Passenger Side
6L3Z-25218A42-AA
Q: How to Service the Front Door Lock Actuator on Mercury Monterey?
A:
The service of front door lock actuators begins with removing the front door trim. The next step requires removing the three front door latch bolts followed by torquing them to 9 Nm (80 lb-in) before reinstalling them properly. Disconnect the exterior front door handle actuating rod while also disconnecting any present door lock cylinder actuating rod. Use the front door latch to reach the door lock actuator before detaching its electrical connector. Complete the door lock actuator removal process by proceeding to install it onto the front door latch while following the reverse steps of removal.