Ford 6L3Z-25218A43-AA
Lock Actuator, Front Driver Side

The power door lock actuator repair requires starting by taking out the door latch either from the front or rear depending on the serviced door type. You should release the locking tab to detach the door lock actuator after removing the latch. You should conduct installation by following the steps reversed from the removal process.

Service of power door locks requires starting by uninstalling the door ajar switch. Detaching the tab will allow you to slide the door lock actuator off the latch before completely removing it. You should execute the opposite sequence for installing the new actuator. The front door latch presentation exists while the rear door latch operates with the same configuration.

The service of the power door lock actuator begins when users detach both the front door latch and the door lock actuator from the latch system. The installation process requires performing the opposite steps of removal to finish the work.

The front door lock actuator service requires removal of the front door latch followed by detachment of the door lock actuator from the latch. You should execute the removal process in reverse order to install the new actuator.

Service on the front door lock actuator requires starting with the removal of the front door trim panel. You must remove the three front door latch bolts at this point while you need to set their torque to 12 Nm (9 lb-ft) upon installing everything back together. The exterior front door handle actuating rod followed by the door lock cylinder rod need disconnection. Behavior the front door latch until you can reach the door lock actuator then remove its electrical connector from the unit. You must take the door lock actuator from the front door latch before completing reinstallation through reverse order operations.

A repair or servicing procedure for the power door lock actuator requires initial removal of the door latch according to procedures for front or rear door latches on Crew Cab and Excursion models. The next step requires removal of the door ajar switch. The service requires releasing the tab to remove the door lock actuator that slides off the latch and turns into full removal. Moreover the front door latch picture demonstrates the process while the method for the rear door latch is very similar. The installation process requires you to execute the opposite operations which were performed during removal.

Repair and servicing of the power door lock actuator begins by taking out the door ajar switch. Sliding the actuator off the latch assembly becomes possible after lifting its locking tab. The installation of the door lock actuator should only proceed when the actuating lever successfully inserts into the actuating pin. The completion of installation requires following the opposite steps used for removal.

A service technician should kick off the power door lock actuator work by taking out the front door latch. The installation requires beginning with sliding the front door latch actuator beyond the front door latch assembly. The installation process should begin by performing a reverse action of the removal steps.

Starting the power door lock actuator servicing requires the window to reach its highest position. The first step involves dismantling the front door trim panel before placing the watershield to the side. Detach both lock cylinder rod connections when they apply from their respective components between the lock cylinder and exterior door handle. Next detach the three front door latch screws before reinstallation where you should tighten them to 12 Nm (9 lb-ft). First disconnect the electrical connector of the front door latch followed by removing power door lock actuator electrical connector and door ajar switch electrical connector. First remove the front door latch before taking out the door ajar switch and front door actuator. After completing the installation you should reverse all steps of removal while applying lubrication to the front door latch.

A power door lock actuator requires service that begins with door trim panel removal and then proceeding with removing the door latch and door ajar switch while releasing the locking tab. Service the power door lock actuator by removing the adjunct actuator next. The reverse methods should be followed for installation.

Service operations for the power door lock actuator should begin by extracting the front door latch. The next step requires separating the door lock actuator from its connection with the latch. Reinstall the power door lock actuator by performing the opposite actions taken for removal.

You should start service and repair tasks on the power sliding door release actuator by taking out the power sliding door trim panel and then unscrewing the latches and remote control assembly screws. The exterior door handle linkage and latch release actuator need to be disconnected first. Place the remote control assembly next to the door before unconnecting its connector while taking off the cap. The technician should then take off the latch release actuator. To reinstall the device follow the complete opposite steps of removal.

Begin by removing the door latch and the door ajar switch.

No, the procedure for the front door latch is similar to that of the rear door latch.

Release the tab and slide the door lock actuator off the latch, then remove the door lock actuator.

Reverse the steps taken during removal for installation.

Reverse the removal procedure.

Reverse the removal procedure.

Reverse the removal procedure.

Reverse the removal procedure.

Remove the rear door lock actuator.

Reverse the removal procedure.

The procedure for the front door latch is illustrated, but the rear door latch follows a similar process.

Position the front door latch to gain access to the door lock actuator.

Open the door halfway to disconnect the rear cable clip and remove the rear cable, feeding both cables through the vehicle's interior.

Reverse the removal procedure.

Begin by removing the door ajar switch.

Reverse the steps taken during removal.

Release the tab on the door lock actuator and slide it off the door latch.

Reverse the removal procedure.

Reverse the steps taken during removal.

Reverse the removal procedure.

Feed both cables through the vehicle's interior, then disconnect the power sliding door module electrical connectors.

Remove the latch release actuator.

Reverse the removal procedure.

Remove the front door latch.

Lift the locking tab and slide the actuator off the latch assembly.

Simply reverse the removal procedure.

Slide the front door latch actuator out from the front door latch assembly.

Next, release the locking tab to detach the rear door lock actuator.

Feed the front cable and pulley guide nozzle through the body to the exterior, install the bolts, and repeat the process for the rear cable.

Remove the front door latch.

First, remove the door ajar switch.

First, remove the rear door latch.

Ensure the cables do not rub against the sheet metal and feed them fully through the opening.

Reverse the removal procedure to secure the new actuator in place.

Disconnect the electrical connector from the door lock actuator.

Remove the sliding door remote control.

Reverse the removal procedure.

Lift the locking tab and slide the actuator off the latch assembly.

Remove the door latch.