How can you effectively remove air from the Hydro-Boost power brake booster system on 2000 Ford E-150 Econoline?

The Hydro-Boost power brake booster contains a built-in bleed feature which can be cleared through the steps mentioned below. Start the process by adding either Motorcraft MERCON(r) ATF XT-2-QDX or -DDX or a MERCON(r) equivalent to the power steering oil reservoir. Reposition the Powertrain Control Module (PCM) relay to stop engine start-up followed by several seconds of cranking the engine. Check the power steering oil reservoir fluid level and add fluid if required before placing back the PCM relay. Begin motor operation but after the engine starts turn the steering wheel between stops twice and then shut off the engine. Braking the vehicle several times through pedal presses removes pressure from the accumulator so perform steps again. Stop the engine to wait until the foam disappears if it starts to form. Perform the procedure again to eliminate all air trapped in the system until foaming stops completely.

OEM 2000 Ford E-150 Econoline Brake Booster

Brake Power Booster

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

3 Brake Boosters found

View related parts
2000 Ford E-150 Econoline Brake Booster
Part Number: XC2Z-2005-AA
Product Specifications
- Other Name: Booster Assembly - Brake; Power Brake Booster
- Base No.: 2005
- Item Weight: 16.10 Pounds
- Item Dimensions: 8.9 x 8.5 x 17.9 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: XC2Z-2005-AA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2000 Ford E-150 Econoline Submodels:
- Base, XL | 6 Cyl 4.2 L GAS, 8 Cyl 4.6 L GAS, 8 Cyl 5.4 L GAS
View related parts
2000 Ford E-150 Econoline Brake Booster
Part Number: 5C2Z-2005-BA
Product Specifications
- Other Name: Booster Assembly - Brake; Power Brake Booster
- Base No.: 2005
- Item Weight: 9.50 Pounds
- Item Dimensions: 12.2 x 11.9 x 13.5 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 5C2Z-2005-BA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2000 Ford E-150 Econoline Submodels:
- Base, XL | 6 Cyl 4.2 L GAS, 8 Cyl 4.6 L GAS, 8 Cyl 5.4 L GAS
View related parts
2000 Ford E-150 Econoline Brake Booster
Part Number: 3C2Z-2005-CA
Product Specifications
- Other Name: Booster Assembly - Brake; Power Brake Booster; Booster Assembly
- Base No.: 2005
- Item Weight: 13.00 Pounds
- Item Dimensions: 11.0 x 11.3 x 14.2 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 3C2Z-2005-CA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2000 Ford E-150 Econoline Submodels:
- Base, XL | 6 Cyl 4.2 L GAS, 8 Cyl 4.6 L GAS, 8 Cyl 5.4 L BI-FUEL, 8 Cyl 5.4 L GAS

2000 Ford E-150 Econoline Brake Booster

If you're seeking quality and affordability, look no further than our extensive inventory of genuine 2000 Ford E-150 Econoline Brake Booster available at FordPartsDeal.com. You can confidently purchase our OEM 2000 Ford E-150 Econoline Brake Booster as they are supported by the manufacturer's warranty and our hassle-free return policy, alongside the benefit of our fast delivery service.

2000 Ford E-150 Econoline Brake Booster Parts Questions & Experts Answers

Q: How can you effectively remove air from the Hydro-Boost power brake booster system on 2000 Ford E-150 Econoline?
A: The Hydro-Boost power brake booster contains a built-in bleed feature which can be cleared through the steps mentioned below. Start the process by adding either Motorcraft MERCON(r) ATF XT-2-QDX or -DDX or a MERCON(r) equivalent to the power steering oil reservoir. Reposition the Powertrain Control Module (PCM) relay to stop engine start-up followed by several seconds of cranking the engine. Check the power steering oil reservoir fluid level and add fluid if required before placing back the PCM relay. Begin motor operation but after the engine starts turn the steering wheel between stops twice and then shut off the engine. Braking the vehicle several times through pedal presses removes pressure from the accumulator so perform steps again. Stop the engine to wait until the foam disappears if it starts to form. Perform the procedure again to eliminate all air trapped in the system until foaming stops completely.