How to Service and Repair the Rear Two-Piece Drive Shaft on 2000 Ford F-350 Super Duty?

The first step to work on the rear two-piece drive/propeller shaft involves vehicle lifting and support followed by driveshaft indexing at the axle flange. The replacement of new bolts and retainers becomes necessary during and after the third instance of removal. Brittle Corrosion is the initial step to perform this service which involves marking the drive shaft and then unbolting the driveshaft from its position at the rear axle area after removing the U-joint retainers. Mechanics wire should be used to provide support for the driveshaft. To disconnect the driveshaft in vehicles with transfer cases or manual transmissions, users must first mark bolts that connect the driveshaft to the transfer case or transmission then they can support the shaft with mechanics wire. The automatic transmission process starts with indexing the output shaft to slip yoke before removal of center bearing support bolts and driveshaft assembly. Move the driveshaft backwards while lowering it from the transmission output shaft before plugging the extension housing to stop fluid leakages. Thoroughly clean grease deposits together with dirt and rust from the driveshaft yoke areas as well as all components before wiping the bearing and keeping the rubber insulator of the driveshaft center bearing free from solvent immersion. Checks should be performed for torn or punctured driveshaft slip yoke boots and rough movements from driveshaft center bearing supports and evidence of damage on the center bearing rubber insulator for repairing defective components during the inspection process. To install the driveshaft you need to place bolts and retainers back after the third removal step while inspecting transmission and transfer case and axle seals for damage and applying Premium Long-Life Grease XG-1-C or equivalent meeting Ford specification ESA-M1C75-13 to lubricate the slip yoke spline before aligning the driveshaft with index marks made before removal or by aligning the yellow mark on the driveshaft tube with the yellow mark on the rear axle flange. The bolt threads must be cleaned before the third removal while applying Loctite(R) 242 or equivalent followed by the reverse order removal procedure.

OEM 2000 Ford F-350 Super Duty Drive Shaft

Axle Shaft

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

62 Drive Shafts found

View related parts
2000 Ford F-350 Super Duty Drive Shaft
Part Number: 5C3Z-4A376-FA
$392.25 MSRP: $567.69
You Save: $175.44 (31%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft Assembly - Drive; Driveshaft
- Base No.: 4A376
- Item Weight: 34.20 Pounds
- Item Dimensions: 6.3 x 6.1 x 56.2 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 5C3Z-4A376-FA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2000 Ford F-350 Super Duty Submodels:
- King Ranch, Lariat, XL, XLT | 8 Cyl 7.3 L DIESEL
View related parts
2000 Ford F-350 Super Duty Drive Shaft
Part Number: 5C3Z-4A376-D
$435.84 MSRP: $590.77
You Save: $154.93 (27%)
Ships in 1 Business Day
ADD TO CART
Product Specifications
- Other Name: Shaft Assembly - Drive; Driveshaft
- Base No.: 4A376
- Item Weight: 38.20 Pounds
- Item Dimensions: 6.1 x 6.3 x 55.7 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 5C3Z-4A376-D
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2000 Ford F-350 Super Duty Submodels:
- King Ranch, Lariat, XL, XLT | 8 Cyl 7.3 L DIESEL
View related parts
2000 Ford F-350 Super Duty Axle Shaft, Front Driver Side
Part Number: 4C3Z-3220-BA
$410.76 MSRP: $603.17
You Save: $192.41 (32%)
ADD TO CART
Product Specifications
- Other Name: Shaft - Front Axle; Axle Shaft Assembly; Axle Assembly
- Position: Front Driver Side
- Replaces: 3C3Z-3220-BA
- Item Weight: 34.90 Pounds
- Item Dimensions: 30.7 x 6.2 x 6.3 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 4C3Z-3220-BA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2000 Ford F-350 Super Duty Submodels:
- Harley-Davidson Edition, King Ranch, Lariat, XL, XLT | 10 Cyl 6.8 L GAS, 8 Cyl 5.4 L GAS, 8 Cyl 6.0 L DIESEL, 8 Cyl 7.3 L DIESEL
View related parts
2000 Ford F-350 Super Duty Axle Shaft, Front Passenger Side
Part Number: 4C3Z-3219-BA
$454.45 MSRP: $667.33
You Save: $212.88 (32%)
ADD TO CART
Product Specifications
- Other Name: Shaft - Front Axle; Axle Shaft Assembly; Axle Assembly
- Position: Front Passenger Side
- Replaces: 3C3Z-3219-BA
- Item Weight: 35.40 Pounds
- Item Dimensions: 6.2 x 6.2 x 29.4 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 4C3Z-3219-BA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2000 Ford F-350 Super Duty Submodels:
- Harley-Davidson Edition, King Ranch, Lariat, XL, XLT | 10 Cyl 6.8 L GAS, 8 Cyl 5.4 L GAS, 8 Cyl 6.0 L DIESEL, 8 Cyl 7.3 L DIESEL
View related parts
2000 Ford F-350 Super Duty Drive Shaft
Part Number: F81Z-4R602-GA
$574.31 MSRP: $778.46
You Save: $204.15 (27%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft Assembly - Drive; Driveshaft
- Item Weight: 61.00 Pounds
- Condition: New
- Fitment Type: Direct Replacement
- SKU: F81Z-4R602-GA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following 2000 Ford F-350 Super Duty Submodels:
- Lariat, XL, XLT | 8 Cyl 5.4 L GAS
View related parts
2000 Ford F-350 Super Duty Drive Shaft
Part Number: 5C3Z-4A376-A
Product Specifications
- Other Name: Shaft Assembly - Drive; Driveshaft
- Base No.: 4A376
- Item Weight: 35.50 Pounds
- Item Dimensions: 63.0 x 6.3 x 6.2 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 5C3Z-4A376-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2000 Ford F-350 Super Duty Submodels:
- Harley-Davidson Edition, King Ranch, Lariat, XL, XLT | 10 Cyl 6.8 L GAS, 8 Cyl 5.4 L GAS
View related parts
2000 Ford F-350 Super Duty Drive Shaft
Part Number: F81Z-4602-AG
Product Specifications
- Other Name: Shaft Assembly - Drive; Driveshaft
- Base No.: 4602
- Item Weight: 24.20 Pounds
- Condition: New
- Fitment Type: Direct Replacement
- SKU: F81Z-4602-AG
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2000 Ford F-350 Super Duty Submodels:
- Lariat, XL, XLT | 8 Cyl 5.4 L GAS
View related parts
2000 Ford F-350 Super Duty Drive Shaft
Part Number: F81Z-4R602-LKE
Product Specifications
- Other Name: Shaft Assembly - Drive; Driveshaft
- Condition: New
- Fitment Type: Direct Replacement
- SKU: F81Z-4R602-LKE
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following 2000 Ford F-350 Super Duty Submodels:
- Lariat, XL, XLT | 8 Cyl 7.3 L DIESEL
View related parts
2000 Ford F-350 Super Duty Drive Shaft
Part Number: 5C3Z-4A376-B
Product Specifications
- Other Name: Shaft Assembly - Drive; Driveshaft
- Base No.: 4A376
- Item Dimensions: 26.4 x 6.0 x 15.5 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 5C3Z-4A376-B
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2000 Ford F-350 Super Duty Submodels:
- Harley-Davidson Edition, King Ranch, Lariat, XL, XLT | 10 Cyl 6.8 L GAS, 8 Cyl 5.4 L GAS
View related parts
2000 Ford F-350 Super Duty Drive Shaft
Part Number: 5C3Z-4A376-C
Product Specifications
- Other Name: Shaft Assembly - Drive; Driveshaft
- Base No.: 4A376
- Item Dimensions: 25.7 x 6.2 x 15.0 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 5C3Z-4A376-C
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2000 Ford F-350 Super Duty Submodels:
- Harley-Davidson Edition, King Ranch, Lariat, XL, XLT | 10 Cyl 6.8 L GAS, 8 Cyl 5.4 L GAS
View related parts
2000 Ford F-350 Super Duty Drive Shaft
Part Number: F81Z-4602-ABD
Product Specifications
- Other Name: Shaft Assembly - Drive; Driveshaft
- Base No.: 4602
- Condition: New
- Fitment Type: Direct Replacement
- SKU: F81Z-4602-ABD
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following 2000 Ford F-350 Super Duty Submodels:
- Lariat, XL, XLT | 8 Cyl 7.3 L DIESEL
View related parts
2000 Ford F-350 Super Duty Drive Shaft
Part Number: F81Z-4602-ACC
Product Specifications
- Other Name: Shaft Assembly - Drive; Driveshaft
- Base No.: 4602
- Condition: New
- Fitment Type: Direct Replacement
- SKU: F81Z-4602-ACC
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following 2000 Ford F-350 Super Duty Submodels:
- Lariat, XL, XLT | 10 Cyl 6.8 L GAS
View related parts
2000 Ford F-350 Super Duty Drive Shaft
Part Number: F81Z-4602-AD
Product Specifications
- Other Name: Shaft Assembly - Drive; Driveshaft
- Base No.: 4602
- Condition: New
- Fitment Type: Direct Replacement
- SKU: F81Z-4602-AD
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following 2000 Ford F-350 Super Duty Submodels:
- Lariat, XL, XLT | 8 Cyl 5.4 L GAS
View related parts
2000 Ford F-350 Super Duty Drive Shaft
Part Number: F81Z-4602-CHF
Product Specifications
- Other Name: Shaft Assembly - Drive; Driveshaft
- Base No.: 4602
- Condition: New
- Fitment Type: Direct Replacement
- SKU: F81Z-4602-CHF
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following 2000 Ford F-350 Super Duty Submodels:
- Lariat, XL, XLT | 8 Cyl 7.3 L DIESEL
View related parts
2000 Ford F-350 Super Duty Drive Shaft
Part Number: F81Z-4602-CMF
Product Specifications
- Other Name: Shaft Assembly - Drive; Driveshaft
- Base No.: 4602
- Condition: New
- Fitment Type: Direct Replacement
- SKU: F81Z-4602-CMF
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following 2000 Ford F-350 Super Duty Submodels:
- Harley-Davidson Edition, King Ranch, Lariat, XL, XLT | 10 Cyl 6.8 L GAS
View related parts
2000 Ford F-350 Super Duty Drive Shaft
Part Number: F81Z-4602-CTG
Product Specifications
- Other Name: Shaft Assembly - Drive; Driveshaft
- Base No.: 4602
- Condition: New
- Fitment Type: Direct Replacement
- SKU: F81Z-4602-CTG
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following 2000 Ford F-350 Super Duty Submodels:
- Lariat, XL, XLT | 8 Cyl 7.3 L DIESEL
View related parts
2000 Ford F-350 Super Duty Drive Shaft
Part Number: F81Z-4602-DB
Product Specifications
- Other Name: Shaft Assembly - Drive; Driveshaft
- Base No.: 4602
- Condition: New
- Fitment Type: Direct Replacement
- SKU: F81Z-4602-DB
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following 2000 Ford F-350 Super Duty Submodels:
- Lariat, XL, XLT | 10 Cyl 6.8 L GAS
View related parts
2000 Ford F-350 Super Duty Drive Shaft
Part Number: F81Z-4602-DCG
Product Specifications
- Other Name: Shaft Assembly - Drive; Driveshaft
- Base No.: 4602
- Condition: New
- Fitment Type: Direct Replacement
- SKU: F81Z-4602-DCG
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following 2000 Ford F-350 Super Duty Submodels:
- Lariat, XL, XLT | 10 Cyl 6.8 L GAS
View related parts
2000 Ford F-350 Super Duty Drive Shaft
Part Number: F81Z-4602-DGG
Product Specifications
- Other Name: Shaft Assembly - Drive; Driveshaft
- Base No.: 4602
- Condition: New
- Fitment Type: Direct Replacement
- SKU: F81Z-4602-DGG
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following 2000 Ford F-350 Super Duty Submodels:
- Lariat, XL, XLT | 8 Cyl 5.4 L GAS
View related parts
2000 Ford F-350 Super Duty Drive Shaft
Part Number: F81Z-4602-DPG
Product Specifications
- Other Name: Shaft Assembly - Drive; Driveshaft
- Base No.: 4602
- Item Dimensions: 25.2 x 6.2 x 15.5 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: F81Z-4602-DPG
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2000 Ford F-350 Super Duty Submodels:
- Lariat, XL, XLT | 10 Cyl 6.8 L GAS

| Page 1 of 4 |Next >

1-20 of 62 Results

2000 Ford F-350 Super Duty Drive Shaft

If you're seeking quality and affordability, look no further than our extensive inventory of genuine 2000 Ford F-350 Super Duty Drive Shaft available at FordPartsDeal.com. You can confidently purchase our OEM 2000 Ford F-350 Super Duty Drive Shaft as they are supported by the manufacturer's warranty and our hassle-free return policy, alongside the benefit of our fast delivery service.

2000 Ford F-350 Super Duty Drive Shaft Parts Questions & Experts Answers

Q: How to Service and Repair the Rear Two-Piece Drive Shaft on 2000 Ford F-350 Super Duty?
A: The first step to work on the rear two-piece drive/propeller shaft involves vehicle lifting and support followed by driveshaft indexing at the axle flange. The replacement of new bolts and retainers becomes necessary during and after the third instance of removal. Brittle Corrosion is the initial step to perform this service which involves marking the drive shaft and then unbolting the driveshaft from its position at the rear axle area after removing the U-joint retainers. Mechanics wire should be used to provide support for the driveshaft. To disconnect the driveshaft in vehicles with transfer cases or manual transmissions, users must first mark bolts that connect the driveshaft to the transfer case or transmission then they can support the shaft with mechanics wire. The automatic transmission process starts with indexing the output shaft to slip yoke before removal of center bearing support bolts and driveshaft assembly. Move the driveshaft backwards while lowering it from the transmission output shaft before plugging the extension housing to stop fluid leakages. Thoroughly clean grease deposits together with dirt and rust from the driveshaft yoke areas as well as all components before wiping the bearing and keeping the rubber insulator of the driveshaft center bearing free from solvent immersion. Checks should be performed for torn or punctured driveshaft slip yoke boots and rough movements from driveshaft center bearing supports and evidence of damage on the center bearing rubber insulator for repairing defective components during the inspection process. To install the driveshaft you need to place bolts and retainers back after the third removal step while inspecting transmission and transfer case and axle seals for damage and applying Premium Long-Life Grease XG-1-C or equivalent meeting Ford specification ESA-M1C75-13 to lubricate the slip yoke spline before aligning the driveshaft with index marks made before removal or by aligning the yellow mark on the driveshaft tube with the yellow mark on the rear axle flange. The bolt threads must be cleaned before the third removal while applying Loctite(R) 242 or equivalent followed by the reverse order removal procedure.