How to Service and Repair the One-Piece, 4x2 Drive Shaft with a 137-Inch and 141-Inch Wheelbase on 2001 Ford F-250 Super Duty?

The service process for the one-piece 4x2 driveshaft associated with vehicles that have 137-inch or 141-inch wheelbase starts with vehicle lifting and suspension installation. Vehicle owners with automatic transmissions should stop the output shaft movement before marking the driveshaft and transmission extension housing positions. For manual transmission vehicles, index-mark the driveshaft yoke and the transmission flange. Driveshaft index-marking and pinion flange indexing apply to all vehicles except the Excursion, after which the four bolts and two U-joint retainers need removal and discarding. The rear axle pinion flange and driveshaft yoke of the Excursion require marking as a first step before removing and discarding all four bolts. You should remove the four bolts on manual transmission vehicles before disposal. The driveshaft must be detached from both its connections to the rear axle pinion flange and if the transmission is manual the driveshaft should be completely removed from the vehicle. In vehicles with automatic transmission the driveshaft requires dropping and sliding off the transmission output shaft. Apply tape to the bearing cups to avoid their dislodgement from the spider while using tape also to seal the automatic transmission extension housing against fluid leakage. The procedure to disconnect the driveshaft yoke from the rear axle pinion flange requires a suitable tool during Excursion service but avoid striking driveshaft components with the tool. Before installing the driveshaft slip-yoke on the transmission output shaft, vehicles with automatic transmission require Premium Long-Life Grease XG-1-C or equivalent FSA-M1C75-B-rated grease for the spline lubrication and the removal of extension housing plug helps achieve proper index mark alignment. Users should line up the index marks when installing the driveshaft yoke to the transmission flange when working on manual transmission systems. Unlike the Excursion model all other vehicles require removal of bearing cup tape followed by index mark alignment before placing cups into the pinion flange of the rear axle. Place the driveshaft yoke onto the rear axle pinion flange on the Excursion while aligning the index marks followed by installing the four new bolts in a loose manner. While working on vehicles with manual transmission the mechanic must use new bolts for assembly then follow up with loose installation of these four new bolts. All vehicles require installation of new bolts as well as new retainers followed by securement of the two new retainers and four new bolts. Users should check that the driveshaft yoke fits perfectly on the flange before tightening every bolt by following a cross-pattern sequence. Torque the recently installed four bolts on vehicles using manual transmission before lowering down the vehicle.

OEM 2001 Ford F-250 Super Duty Drive Shaft

Axle Shaft

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

67 Drive Shafts found

View related parts
2001 Ford F-250 Super Duty Drive Shaft Part Number: 5C3Z-4A376-FA
$392.25 MSRP: $567.69
You Save: $175.44 (31%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft Assembly - Drive; Driveshaft
- Base No.: 4A376
- Item Weight: 34.20 Pounds
- Item Dimensions: 6.3 x 6.1 x 56.2 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 5C3Z-4A376-FA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2001 Ford F-250 Super Duty Submodels:
- Lariat, XL, XLT | 8 Cyl 7.3 L DIESEL
View related parts
2001 Ford F-250 Super Duty Axle Shaft, Front Driver Side Part Number: 4C3Z-3220-BA
$410.76 MSRP: $603.17
You Save: $192.41 (32%)
ADD TO CART
Product Specifications
- Other Name: Shaft - Front Axle; Axle Shaft Assembly; Axle Assembly
- Position: Front Driver Side
- Replaces: 3C3Z-3220-BA
- Item Weight: 34.90 Pounds
- Item Dimensions: 30.7 x 6.2 x 6.3 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 4C3Z-3220-BA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2001 Ford F-250 Super Duty Submodels:
- Harley-Davidson Edition, King Ranch, Lariat, XL, XLT | 10 Cyl 6.8 L GAS, 8 Cyl 5.4 L GAS, 8 Cyl 6.0 L DIESEL, 8 Cyl 7.3 L DIESEL
View related parts
2001 Ford F-250 Super Duty Axle Shaft, Front Passenger Side Part Number: 4C3Z-3219-BA
$454.45 MSRP: $667.33
You Save: $212.88 (32%)
ADD TO CART
Product Specifications
- Other Name: Shaft - Front Axle; Axle Shaft Assembly; Axle Assembly
- Position: Front Passenger Side
- Replaces: 3C3Z-3219-BA
- Item Weight: 35.40 Pounds
- Item Dimensions: 6.2 x 6.2 x 29.4 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 4C3Z-3219-BA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2001 Ford F-250 Super Duty Submodels:
- Harley-Davidson Edition, King Ranch, Lariat, XL, XLT | 10 Cyl 6.8 L GAS, 8 Cyl 5.4 L GAS, 8 Cyl 6.0 L DIESEL, 8 Cyl 7.3 L DIESEL
View related parts
2001 Ford F-250 Super Duty Drive Shaft Part Number: F81Z-4R602-GA
$574.31 MSRP: $778.46
You Save: $204.15 (27%)
Ships in 1-3 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft Assembly - Drive; Driveshaft
- Item Weight: 61.00 Pounds
- Condition: New
- Fitment Type: Direct Replacement
- SKU: F81Z-4R602-GA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following 2001 Ford F-250 Super Duty Submodels:
- Lariat, XL, XLT | 10 Cyl 6.8 L GAS, 8 Cyl 5.4 L GAS
View related parts
2001 Ford F-250 Super Duty Drive Shaft Part Number: 5C3Z-4A376-D
$435.84 MSRP: $590.77
You Save: $154.93 (27%)
Product Specifications
- Other Name: Shaft Assembly - Drive; Driveshaft
- Base No.: 4A376
- Item Weight: 38.20 Pounds
- Item Dimensions: 6.1 x 6.3 x 55.7 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 5C3Z-4A376-D
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2001 Ford F-250 Super Duty Submodels:
- Lariat, XL, XLT | 8 Cyl 7.3 L DIESEL
View related parts
2001 Ford F-250 Super Duty Drive Shaft Part Number: 5C3Z-4A376-A
Product Specifications
- Other Name: Shaft Assembly - Drive; Driveshaft
- Base No.: 4A376
- Item Weight: 35.50 Pounds
- Item Dimensions: 63.0 x 6.3 x 6.2 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 5C3Z-4A376-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2001 Ford F-250 Super Duty Submodels:
- Harley-Davidson Edition, King Ranch, Lariat, XL, XLT | 10 Cyl 6.8 L GAS, 8 Cyl 5.4 L GAS
View related parts
2001 Ford F-250 Super Duty Drive Shaft Part Number: F81Z-4602-AG
Product Specifications
- Other Name: Shaft Assembly - Drive; Driveshaft
- Base No.: 4602
- Item Weight: 24.20 Pounds
- Condition: New
- Fitment Type: Direct Replacement
- SKU: F81Z-4602-AG
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2001 Ford F-250 Super Duty Submodels:
- Lariat, XL, XLT | 8 Cyl 5.4 L GAS
View related parts
2001 Ford F-250 Super Duty Drive Shaft Part Number: F81Z-4R602-LKE
Product Specifications
- Other Name: Shaft Assembly - Drive; Driveshaft
- Condition: New
- Fitment Type: Direct Replacement
- SKU: F81Z-4R602-LKE
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following 2001 Ford F-250 Super Duty Submodels:
- Lariat, XL, XLT | 8 Cyl 7.3 L DIESEL
View related parts
2001 Ford F-250 Super Duty Drive Shaft Part Number: 1L3Z-4R602-AA
Product Specifications
- Other Name: Shaft Assembly - Drive; Driveshaft
- Item Dimensions: 9.9 x 13.0 x 55.1 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 1L3Z-4R602-AA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following 2001 Ford F-250 Super Duty Submodels:
- Lariat, XL, XLT | 8 Cyl 5.4 L GAS
View related parts
2001 Ford F-250 Super Duty Drive Shaft Part Number: 5C3Z-4A376-B
Product Specifications
- Other Name: Shaft Assembly - Drive; Driveshaft
- Base No.: 4A376
- Item Dimensions: 26.4 x 6.0 x 15.5 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 5C3Z-4A376-B
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2001 Ford F-250 Super Duty Submodels:
- Harley-Davidson Edition, King Ranch, Lariat, XL, XLT | 10 Cyl 6.8 L GAS, 8 Cyl 5.4 L GAS
View related parts
2001 Ford F-250 Super Duty Drive Shaft Part Number: 5C3Z-4A376-C
Product Specifications
- Other Name: Shaft Assembly - Drive; Driveshaft
- Base No.: 4A376
- Item Dimensions: 25.7 x 6.2 x 15.0 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 5C3Z-4A376-C
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2001 Ford F-250 Super Duty Submodels:
- Harley-Davidson Edition, King Ranch, Lariat, XL, XLT | 10 Cyl 6.8 L GAS, 8 Cyl 5.4 L GAS
View related parts
2001 Ford F-250 Super Duty Drive Shaft Part Number: 5C3Z-4R602-H
Product Specifications
- Other Name: Shaft Assembly - Drive; Driveshaft
- Base No.: 4R602
- Item Weight: 31.50 Pounds
- Item Dimensions: 26.2 x 6.0 x 15.8 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 5C3Z-4R602-H
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2001 Ford F-250 Super Duty Submodels:
- Harley-Davidson Edition, King Ranch, Lariat, XL, XLT | 10 Cyl 6.8 L GAS
View related parts
2001 Ford F-250 Super Duty Drive Shaft Part Number: F81Z-4602-ABD
Product Specifications
- Other Name: Shaft Assembly - Drive; Driveshaft
- Base No.: 4602
- Condition: New
- Fitment Type: Direct Replacement
- SKU: F81Z-4602-ABD
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following 2001 Ford F-250 Super Duty Submodels:
- Lariat, XL, XLT | 8 Cyl 7.3 L DIESEL
View related parts
2001 Ford F-250 Super Duty Drive Shaft Part Number: F81Z-4602-ACC
Product Specifications
- Other Name: Shaft Assembly - Drive; Driveshaft
- Base No.: 4602
- Condition: New
- Fitment Type: Direct Replacement
- SKU: F81Z-4602-ACC
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following 2001 Ford F-250 Super Duty Submodels:
- Lariat, XL, XLT | 10 Cyl 6.8 L GAS
View related parts
2001 Ford F-250 Super Duty Drive Shaft Part Number: F81Z-4602-AD
Product Specifications
- Other Name: Shaft Assembly - Drive; Driveshaft
- Base No.: 4602
- Condition: New
- Fitment Type: Direct Replacement
- SKU: F81Z-4602-AD
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following 2001 Ford F-250 Super Duty Submodels:
- Lariat, XL, XLT | 8 Cyl 5.4 L GAS
View related parts
2001 Ford F-250 Super Duty Drive Shaft Part Number: F81Z-4602-AX
Product Specifications
- Other Name: Shaft Assembly - Drive; Driveshaft
- Base No.: 4602
- Condition: New
- Fitment Type: Direct Replacement
- SKU: F81Z-4602-AX
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following 2001 Ford F-250 Super Duty Submodels:
- Lariat, XL, XLT | 10 Cyl 6.8 L GAS
View related parts
2001 Ford F-250 Super Duty Drive Shaft Part Number: F81Z-4602-AZ
Product Specifications
- Other Name: Shaft Assembly - Drive; Driveshaft
- Manufacturer Note: Parts List No. 217, 137"WB - 4x4 - SRW, THRU 1-6-2002
- Base No.: 4602
- Condition: New
- Fitment Type: Direct Replacement
- SKU: F81Z-4602-AZ
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2001 Ford F-250 Super Duty Submodels:
- Lariat, XL, XLT | 8 Cyl 5.4 L GAS
View related parts
2001 Ford F-250 Super Duty Drive Shaft Part Number: F81Z-4602-CTG
Product Specifications
- Other Name: Shaft Assembly - Drive; Driveshaft
- Base No.: 4602
- Condition: New
- Fitment Type: Direct Replacement
- SKU: F81Z-4602-CTG
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following 2001 Ford F-250 Super Duty Submodels:
- Lariat, XL, XLT | 8 Cyl 7.3 L DIESEL
View related parts
2001 Ford F-250 Super Duty Drive Shaft Part Number: F81Z-4602-DB
Product Specifications
- Other Name: Shaft Assembly - Drive; Driveshaft
- Base No.: 4602
- Condition: New
- Fitment Type: Direct Replacement
- SKU: F81Z-4602-DB
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following 2001 Ford F-250 Super Duty Submodels:
- Lariat, XL, XLT | 10 Cyl 6.8 L GAS
View related parts
2001 Ford F-250 Super Duty Drive Shaft Part Number: F81Z-4602-DCG
Product Specifications
- Other Name: Shaft Assembly - Drive; Driveshaft
- Base No.: 4602
- Condition: New
- Fitment Type: Direct Replacement
- SKU: F81Z-4602-DCG
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following 2001 Ford F-250 Super Duty Submodels:
- Lariat, XL, XLT | 10 Cyl 6.8 L GAS

| Page 1 of 4 |Next >

1-20 of 67 Results

2001 Ford F-250 Super Duty Drive Shaft

If you're seeking quality and affordability, look no further than our extensive inventory of genuine 2001 Ford F-250 Super Duty Drive Shaft available at FordPartsDeal.com. You can confidently purchase our OEM 2001 Ford F-250 Super Duty Drive Shaft as they are supported by the manufacturer's warranty and our hassle-free return policy, alongside the benefit of our fast delivery service.

2001 Ford F-250 Super Duty Drive Shaft Parts Q&A

Q: How to Service and Repair the One-Piece, 4x2 Drive Shaft with a 137-Inch and 141-Inch Wheelbase on 2001 Ford F-250 Super Duty?
A: The service process for the one-piece 4x2 driveshaft associated with vehicles that have 137-inch or 141-inch wheelbase starts with vehicle lifting and suspension installation. Vehicle owners with automatic transmissions should stop the output shaft movement before marking the driveshaft and transmission extension housing positions. For manual transmission vehicles, index-mark the driveshaft yoke and the transmission flange. Driveshaft index-marking and pinion flange indexing apply to all vehicles except the Excursion, after which the four bolts and two U-joint retainers need removal and discarding. The rear axle pinion flange and driveshaft yoke of the Excursion require marking as a first step before removing and discarding all four bolts. You should remove the four bolts on manual transmission vehicles before disposal. The driveshaft must be detached from both its connections to the rear axle pinion flange and if the transmission is manual the driveshaft should be completely removed from the vehicle. In vehicles with automatic transmission the driveshaft requires dropping and sliding off the transmission output shaft. Apply tape to the bearing cups to avoid their dislodgement from the spider while using tape also to seal the automatic transmission extension housing against fluid leakage. The procedure to disconnect the driveshaft yoke from the rear axle pinion flange requires a suitable tool during Excursion service but avoid striking driveshaft components with the tool. Before installing the driveshaft slip-yoke on the transmission output shaft, vehicles with automatic transmission require Premium Long-Life Grease XG-1-C or equivalent FSA-M1C75-B-rated grease for the spline lubrication and the removal of extension housing plug helps achieve proper index mark alignment. Users should line up the index marks when installing the driveshaft yoke to the transmission flange when working on manual transmission systems. Unlike the Excursion model all other vehicles require removal of bearing cup tape followed by index mark alignment before placing cups into the pinion flange of the rear axle. Place the driveshaft yoke onto the rear axle pinion flange on the Excursion while aligning the index marks followed by installing the four new bolts in a loose manner. While working on vehicles with manual transmission the mechanic must use new bolts for assembly then follow up with loose installation of these four new bolts. All vehicles require installation of new bolts as well as new retainers followed by securement of the two new retainers and four new bolts. Users should check that the driveshaft yoke fits perfectly on the flange before tightening every bolt by following a cross-pattern sequence. Torque the recently installed four bolts on vehicles using manual transmission before lowering down the vehicle.