How to service and repair the upper intake manifold on 2001 Ford Ranger?

The service process for the upper intake manifold requires you to first detach both the battery ground cable and Intake Air Temperature (IAT) sensor. Both the air cleaner outlet tube and the accelerator control splash shield need removal. The service technician should disconnect the engine control sensor wires from both the Throttle Position sensor and Idle Air Control valve together with the accelerator cable and speed control when present. Place the accelerator cable bracket aside after removing it from its position. The next step requires the removal of the crankcase vent hose from the valve cover together with vacuum hoses from the intake manifold vacuum tee in addition to the heater water hose from both the intake manifold and the heater line of the vehicle. To replace the EGR valve you need to disconnect the EGR tube at its valve position before loosening the exhaust manifold fitting. Then discard the existing EGR valve gasket during the replacement. Begin by removing the upper intake manifold through the process of unbolt its seven fasteners and discarding the gasket. You should reverse the uninstallation steps to mount the lower intake manifold gasket while installing the upper intake manifold. Apply these bolts in a sequential order by starting at 7 - 10 Nm (62 - 88 inch lbs.) followed by 26 - 38 Nm (20 - 28 ft. lbs.).

OEM 2001 Ford Ranger Intake Manifold

Engine Intake Manifold

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

8 Intake Manifolds found

View related parts
2001 Ford Ranger Intake Manifold Part Number: 4L5Z-9424-A
$377.96 MSRP: $555.00
You Save: $177.04 (32%)
Product Specifications
- Other Name: Kit - Manifold Hardware; Engine Intake Manifold
- Replaces: 1L5Z-9424-DA, 4L5Z-9424-BA
- Base No.: 9424
- Item Weight: 12.50 Pounds
- Item Dimensions: 23.8 x 12.5 x 11.5 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 4L5Z-9424-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2001 Ford Ranger Submodels:
- Edge, FX4, Sport, STX, Tremor, XL, XLT | 6 Cyl 4.0 L GAS
View related parts
2001 Ford Ranger Intake Manifold, Lower Part Number: F57Z-9424-D
Product Specifications
- Other Name: Manifold Assembly - Inlet; Engine Intake Manifold, Lower; Manifold
- Position: Lower
- Base No.: 9424
- Item Weight: 7.60 Pounds
- Item Dimensions: 18.6 x 13.5 x 9.0 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: F57Z-9424-D
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2001 Ford Ranger Submodels:
- Splash, Sport, STX, XL, XL Sport, XLT | 4 Cyl 2.3 L GAS, 4 Cyl 2.5 L GAS
View related parts
2001 Ford Ranger Intake Manifold Part Number: 1L5Z-9424-A
Product Specifications
- Other Name: Manifold Assembly - Inlet; Engine Intake Manifold
- Replaces: 1L5Z-9424-AN
- Base No.: 9424
- Item Weight: 10.80 Pounds
- Item Dimensions: 19.4 x 16.5 x 13.7 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 1L5Z-9424-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2001 Ford Ranger Submodels:
- XL, XLT | 4 Cyl 2.3 L GAS
View related parts
2001 Ford Ranger Intake Manifold, Upper Part Number: F87Z-9424-GA
Product Specifications
- Other Name: Manifold Assembly - Inlet; Engine Intake Manifold, Upper; Manifold
- Manufacturer Note: Upper , Unleaded/Flex Fuel Ethanol
- Position: Upper
- Base No.: 9424
- Item Weight: 15.80 Pounds
- Item Dimensions: 19.0 x 13.3 x 9.1 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: F87Z-9424-GA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2001 Ford Ranger Submodels:
- Edge, Splash, XL, XLT | 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS
View related parts
2001 Ford Ranger Intake Manifold, Upper Part Number: 98TZ-9424-CA
Product Specifications
- Other Name: Manifold Assembly - Inlet; Engine Intake Manifold, Upper; Manifold
- Manufacturer Note: Upper - #98TF-9E648-CA. Includes gaskets 9E436/9F670/9E936, OHV - without EGR
- Position: Upper
- Base No.: 9424
- Item Weight: 7.30 Pounds
- Item Dimensions: 19.1 x 13.2 x 8.9 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 98TZ-9424-CA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2001 Ford Ranger Submodels:
- Edge, FX4, Sport, STX, Tremor, XL, XLT | 6 Cyl 4.0 L GAS
View related parts
2001 Ford Ranger Intake Manifold, Lower Part Number: 2L5Z-9424-EARM
Product Specifications
- Other Name: Remanufactured Manifold Assembly - Inlet; Engine Intake Manifold, Lower; Manifold
- Position: Lower
- Replaces: 2L5Z-9424-EA, 2L5Z-9424-AA
- Base No.: 9424
- Item Weight: 8.50 Pounds
- Item Dimensions: 17.6 x 16.3 x 13.1 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 2L5Z-9424-EARM
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2001 Ford Ranger Submodels:
- Edge, Sport, STX, Tremor, XL, XLT | 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS
View related parts
2001 Ford Ranger Intake Manifold, Upper Part Number: F87Z-9424-HA
Product Specifications
- Other Name: Manifold Assembly - Inlet; Engine Intake Manifold, Upper; Manifold
- Manufacturer Note: Upper. Serv 8A505 elbow nipples in assembly only. Note: Dealers must also order/install fitinggs D5AE-9996-DA (pressure regulator) & F2LE-6B608-BA (PCV).
- Position: Upper
- Base No.: 9424
- Item Weight: 7.70 Pounds
- Item Dimensions: 19.3 x 13.0 x 9.1 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: F87Z-9424-HA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2001 Ford Ranger Submodels:
- Splash, XL, XLT | 4 Cyl 2.5 L GAS
View related parts
2001 Ford Ranger Intake Manifold Part Number: 1L5Z-9424-CA
Product Specifications
- Other Name: Manifold Assembly - Inlet
- Manufacturer Note: Upper. Uses M6 attaching hardware (2)W701909-S309 bolt 130mm,(2)W706375-S309 bolt 105mm,(1)W701544-S309 bolt 60mm,(1)stud 6C520 for upper to lower intake
- Base No.: 9424
- Item Weight: 11.90 Pounds
- Item Dimensions: 19.1 x 13.0 x 9.1 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 1L5Z-9424-CA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2001 Ford Ranger Submodels:
- Edge, XL, XLT | 6 Cyl 3.0 L FLEX, 6 Cyl 3.0 L GAS

2001 Ford Ranger Intake Manifold

If you're seeking quality and affordability, look no further than our extensive inventory of genuine 2001 Ford Ranger Intake Manifold available at FordPartsDeal.com. You can confidently purchase our OEM 2001 Ford Ranger Intake Manifold as they are supported by the manufacturer's warranty and our hassle-free return policy, alongside the benefit of our fast delivery service.

2001 Ford Ranger Intake Manifold Parts Q&A

Q: How to service and repair the upper intake manifold on 2001 Ford Ranger?
A: The service process for the upper intake manifold requires you to first detach both the battery ground cable and Intake Air Temperature (IAT) sensor. Both the air cleaner outlet tube and the accelerator control splash shield need removal. The service technician should disconnect the engine control sensor wires from both the Throttle Position sensor and Idle Air Control valve together with the accelerator cable and speed control when present. Place the accelerator cable bracket aside after removing it from its position. The next step requires the removal of the crankcase vent hose from the valve cover together with vacuum hoses from the intake manifold vacuum tee in addition to the heater water hose from both the intake manifold and the heater line of the vehicle. To replace the EGR valve you need to disconnect the EGR tube at its valve position before loosening the exhaust manifold fitting. Then discard the existing EGR valve gasket during the replacement. Begin by removing the upper intake manifold through the process of unbolt its seven fasteners and discarding the gasket. You should reverse the uninstallation steps to mount the lower intake manifold gasket while installing the upper intake manifold. Apply these bolts in a sequential order by starting at 7 - 10 Nm (62 - 88 inch lbs.) followed by 26 - 38 Nm (20 - 28 ft. lbs.).