FordParts
My Garage
My Account
Cart
OEM 2001 Mercury Sable Spindle
Axle Spindle- Select Vehicle by Model
- Select Vehicle by VIN
Select Vehicle by Model
orMake
Model
Year
Select Vehicle by VIN
For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).
4 Spindles found
2001 Mercury Sable Spindle, Rear Passenger Side Part Number: 3F1Z-4A013-AA
$337.16 MSRP: $462.59You Save: $125.43 (28%)Product Specifications- Other Name: Suspension Knuckle, Rear Right; Knuckle
- Position: Rear Passenger Side
- Replaces: YF1Z-4A013-AA
- Base No.: 4A013
- Item Weight: 10.20 Pounds
- Item Dimensions: 4.3 x 4.3 x 7.1 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 3F1Z-4A013-AA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Product Specifications- Other Name: Suspension Knuckle, Rear Right; Knuckle
- Manufacturer Note: R.H., with 18mm diameter hole for anti-lock sensor
- Position: Rear Passenger Side
- Base No.: 4A013
- Item Weight: 11.80 Pounds
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 3F1Z-4A013-BB
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
- Product Specifications
- Other Name: Suspension Knuckle, Rear Left; Knuckle
- Manufacturer Note: L.H., with 18mm diameter hole for anti-lock sensor
- Position: Rear Driver Side
- Base No.: 4A013
- Item Weight: 12.10 Pounds
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 3F1Z-4A013-BA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
- Product Specifications
- Other Name: Suspension Knuckle, Rear Left; Knuckle
- Position: Rear Driver Side
- Replaces: YF1Z-4A013-AB
- Base No.: 4A013
- Item Weight: 10.00 Pounds
- Item Dimensions: 4.3 x 4.2 x 7.1 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 3F1Z-4A013-AB
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
2001 Mercury Sable Spindle
If you're seeking quality and affordability, look no further than our extensive inventory of genuine 2001 Mercury Sable Spindle available at FordPartsDeal.com. You can confidently purchase our OEM 2001 Mercury Sable Spindle as they are supported by the manufacturer's warranty and our hassle-free return policy, alongside the benefit of our fast delivery service.
2001 Mercury Sable Spindle Parts Q&A
- Q: How to service and repair the spindle on a four-door on 2001 Mercury Sable?A: The service and repair process for four-door spindle requires initial hub cap and wheel cover removal. A level ground measurement should determine the spindle to fender lip distance starting from the hub center point. Spindle service begins with wheel hub removal during which you should detach the brake hose with its bolt and then separate the rear brake anti-lock sensor by removing its bolt when present. Wire mechanics should be used to secure the brake backing plate until the brake hose remains free from damage. Throw away the bolts along with nuts and flag bolts before taking out both the nut and washer and bushing. A large screwdriver should be used to open the pinch joint when uninstalling the pinch bolt and rear wheel spindle. First install the new wheel spindle then position a new pinch bolt before choosing not to tighten it at this time. Install the bushing by placing its cupped side away from the bushing then slot in the tension strut before adding the new washer and nut which stays loose. Install new flag bolts and washers and nuts into the lower control arms before continuing without tightening the fasteners at any point. Secure the suspension with a jack stand until the wheel fender reaches the same initial measurement then proceed to tighten all the nuts and bolt. Finish the process by lowering the suspension followed by removing the jack stand. The installation process requires a new gasket along with correct positioning of the rear backing plate and new bolts for securing it. Check the ABS sensor mounting hole for debris since it will cause false activation before placing the brake anti-lock sensor and tightening its bolt. Complete the installation with the wheel hub and ensure the proper wheel alignment then make proper adjustments if required.