How to service and repair the brake caliper on 2002 Mercury Mountaineer?

Before starting brake caliper service operations you must use only Ford High Performance DOT 3 Motor Vehicle Brake Fluid C6AZ-19542-AB or an equivalent solution suitable for Ford specification ESA-M6C25A because other brake fluids will result in permanent breakdown and brake inoperability. Begin brake fluid handling using proper techniques that prevent eye contact and safeguard both painted structures and plastic items while handwashing completely after procedure completion. Simply draining or bleeding brake fluid should also be followed by discarding the fluid since using it again will produce poor results. Avoid using fluid from open containers or contaminated fluids. Begin the disassembly task by taking out both the caliper for the disc brakes and draining all remaining fluid. Install the caliper into a vise and use low air pressure at the fluid port while placing a block of wood between the caliper bridge to push out the pistons from their housing. Discard the piston seals and boots along with the pistons and avoid caliper bore honing since pistons for honed bores are not available; new calipers must be installed in case bore corrosion or scoring surpasses expected wear levels. Before assembling the brake system refrain from using old dust boots or piston seals and maintain all fluid through the hydraulic system inside sealed containers. The specified brake fluid serves for applying lubrication to both piston boot and caliper piston and piston seal while treating all cylinder bores. Place the piston seal and boot onto the piston while being cautious of damaging the seal before placing the caliper piston into the bore by pushing it straight without causing any bending. You should reinstall the disc brake caliper as the last step of the procedure.

OEM 2002 Mercury Mountaineer Brake Caliper

Caliper

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

6 Brake Calipers found

View related parts
2002 Mercury Mountaineer Caliper, Front Driver Side
Part Number: 6L5Z-2B121-A
Product Specifications
- Other Name: Caliper Assembly - Brake - Less Pad; Disc Brake Caliper, Front Left; Brake Caliper Repair Kit; Caliper Assembly - Brake - Less Pads; Brake Caliper
- Position: Front Driver Side
- Replaces: 1L2Z-2B121-AC, 3L2Z-2B121-BB
- Base No.: 2B120
- Item Weight: 8.90 Pounds
- Item Dimensions: 9.9 x 7.4 x 5.8 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 6L5Z-2B121-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2002 Mercury Mountaineer Submodels:
- Base, Convenience, Luxury, Premier | 6 Cyl 4.0 L FLEX, 6 Cyl 4.0 L GAS, 8 Cyl 4.6 L GAS
View related parts
2002 Mercury Mountaineer Caliper, Front
Part Number: 6L5Z-2B120-A
Product Specifications
- Other Name: Caliper Assembly - Brake - Less Pad; Disc Brake Caliper, Front Left, Front Right; Brake Caliper Repair Kit; Caliper Assembly - Brake - Less Pads; Brake Caliper
- Position: Front
- Replaces: 1L2Z-2B120-AB, 3L2Z-2B120-BB
- Base No.: 2B120
- Item Weight: 9.30 Pounds
- Item Dimensions: 5.6 x 7.5 x 10.1 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 6L5Z-2B120-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2002 Mercury Mountaineer Submodels:
- Base, Convenience, Luxury, Premier | 6 Cyl 4.0 L FLEX, 6 Cyl 4.0 L GAS, 8 Cyl 4.6 L GAS
View related parts
2002 Mercury Mountaineer Caliper, Rear Passenger Side
Part Number: 6L2Z-2552-A
Product Specifications
- Other Name: Housing; Disc Brake Caliper, Rear Right; Brake Caliper Repair Kit; Brake Caliper
- Manufacturer Note: Warranty Eligible
- Position: Rear Passenger Side
- Replaces: 1L2Z-2552-AA, 1L2Z-2552-BA, 3L2Z-2552-AA, BRCF-181
- Base No.: 2552
- Item Weight: 6.30 Pounds
- Item Dimensions: 6.9 x 3.6 x 6.6 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 6L2Z-2552-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2002 Mercury Mountaineer Submodels:
- Base, Convenience, Luxury, Premier | 6 Cyl 4.0 L FLEX, 6 Cyl 4.0 L GAS, 8 Cyl 4.6 L GAS, 8 Cyl 5.0 L GAS
View related parts
2002 Mercury Mountaineer Caliper, Passenger Side
Part Number: 2C5Z-2552-AA
Product Specifications
- Other Name: Housing; Brake Caliper Repair Kit; Brake Caliper
- Position: Passenger Side
- Base No.: 2552
- Item Weight: 5.60 Pounds
- Item Dimensions: 3.3 x 5.2 x 6.1 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 2C5Z-2552-AA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2002 Mercury Mountaineer Submodels:
- Base | 6 Cyl 4.0 L FLEX, 6 Cyl 4.0 L GAS, 8 Cyl 4.6 L GAS
View related parts
2002 Mercury Mountaineer Caliper, Rear Driver Side
Part Number: 6L2Z-2553-A
Product Specifications
- Other Name: Housing; Disc Brake Caliper, Rear Left; Brake Caliper Repair Kit; Brake Caliper
- Manufacturer Note: Warranty Eligible
- Position: Rear Driver Side
- Replaces: 1L2Z-2553-AA, 1L2Z-2553-BA, 3L2Z-2553-AA, BRCF-13
- Base No.: 2552
- Item Weight: 5.70 Pounds
- Item Dimensions: 6.8 x 3.6 x 6.6 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 6L2Z-2553-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2002 Mercury Mountaineer Submodels:
- Base, Convenience, Luxury, Premier | 6 Cyl 4.0 L FLEX, 6 Cyl 4.0 L GAS, 8 Cyl 4.6 L GAS, 8 Cyl 5.0 L GAS
View related parts
2002 Mercury Mountaineer Caliper, Driver Side
Part Number: 2C5Z-2553-AA
Product Specifications
- Other Name: Housing; Brake Caliper Repair Kit; Brake Caliper
- Position: Driver Side
- Base No.: 2552
- Item Weight: 5.30 Pounds
- Item Dimensions: 3.3 x 5.2 x 6.1 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 2C5Z-2553-AA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2002 Mercury Mountaineer Submodels:
- Base | 6 Cyl 4.0 L FLEX, 6 Cyl 4.0 L GAS, 8 Cyl 4.6 L GAS

2002 Mercury Mountaineer Brake Caliper

If you're seeking quality and affordability, look no further than our extensive inventory of genuine 2002 Mercury Mountaineer Brake Caliper available at FordPartsDeal.com. You can confidently purchase our OEM 2002 Mercury Mountaineer Brake Caliper as they are supported by the manufacturer's warranty and our hassle-free return policy, alongside the benefit of our fast delivery service.

2002 Mercury Mountaineer Brake Caliper Parts Questions & Experts Answers

Q: How to service and repair the brake caliper on 2002 Mercury Mountaineer?
A: Before starting brake caliper service operations you must use only Ford High Performance DOT 3 Motor Vehicle Brake Fluid C6AZ-19542-AB or an equivalent solution suitable for Ford specification ESA-M6C25A because other brake fluids will result in permanent breakdown and brake inoperability. Begin brake fluid handling using proper techniques that prevent eye contact and safeguard both painted structures and plastic items while handwashing completely after procedure completion. Simply draining or bleeding brake fluid should also be followed by discarding the fluid since using it again will produce poor results. Avoid using fluid from open containers or contaminated fluids. Begin the disassembly task by taking out both the caliper for the disc brakes and draining all remaining fluid. Install the caliper into a vise and use low air pressure at the fluid port while placing a block of wood between the caliper bridge to push out the pistons from their housing. Discard the piston seals and boots along with the pistons and avoid caliper bore honing since pistons for honed bores are not available; new calipers must be installed in case bore corrosion or scoring surpasses expected wear levels. Before assembling the brake system refrain from using old dust boots or piston seals and maintain all fluid through the hydraulic system inside sealed containers. The specified brake fluid serves for applying lubrication to both piston boot and caliper piston and piston seal while treating all cylinder bores. Place the piston seal and boot onto the piston while being cautious of damaging the seal before placing the caliper piston into the bore by pushing it straight without causing any bending. You should reinstall the disc brake caliper as the last step of the procedure.