How to Properly Disassemble and Assemble a Brake Caliper on Mercury Mountaineer?

Begin the brake caliper service by removing the disc brake caliper then draining all existing brake fluid from it. The caliper gets secured within a vise device before caliper pistons can be removed through a process that requires placing a block of wood between the caliper bridge and pistons while using low air pressure applied to the fluid port. Insert the block removal before extracting the calipers and throwing away both piston seals and boots. It is vital to avoid honing the caliper bores since pistons are unavailable for honed bores along with the requirement for a new disc brake caliper replacement when the bore shows excessive scoring or corrosion. When assembling the brake system do not restore piston seals nor dust boots and stay away from reuse of brake fluid after draining or exposing to open containers beyond an extended period. High Performance DOT 3 Brake Fluid C6AZ-19542-AB alongside a DOT 3 equivalent matching Ford specification ESA-M6C25-A should be used as lubrication for the caliper piston and boot together with piston seal and cylinder bores. Put on the disc brake caliper as the last step of the process.

How to service and repair the front brake caliper on Mercury Mountaineer?

Service or repair operations for front brake calipers should start with positioning the vehicle in neutral gear while it rests on a hoist. The correct brake components need permanent protection which requires only using approved DOT 3 motor vehicle brake fluid. The brake hose flow bolt needs removal while placing the brake hose aside with disposal of two copper washers and fluid port capping. The brake caliper sight hole should never be used for piston retraction because it damages their components. The brake caliper guide pin bolts should first be removed along with the brake caliper. The replacement of a new brake caliper becomes necessary in case either leakage or boot damage exists. The installation process begins with a bottom brake caliper bolt located at the top and requires the guide pin brake caliper bolt to be tightened next before mounting the brake caliper and securing guide pin bolts to 72 Nm (53 ft. lbs.). Position the brake hose with two new copper washers before installing the brake hose flow bolt and tightening it to 35 Nm torque. The brake caliper should be bled before performing a normal operational test of the entire braking system. Brake fluid poses a risk to both painted surfaces and plastic materials so surface wash spills right away with water. In case of emergency brake fluid information consult a doctor or dial 1-800-959-3673 to reach Ford/Motorcraft products either in the USA or Canada.

OEM Mercury Mountaineer Brake Caliper

Caliper

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

16 Brake Calipers found

View related parts
Mercury Mountaineer Caliper, Front Driver Side Part Number: XL2Z-2B121-BA
$45.79 MSRP: $66.65
You Save: $20.86 (32%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Caliper With Pads; Disc Brake Caliper, Front Left; Brake Caliper Repair Kit; Brake Caliper
- Manufacturer Note: Caliper housing - LH - 2001/2002
- Position: Front Driver Side
- Replaced by: 1U2Z-2V001-TA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1997-2001 Mercury Mountaineer | Base | 6 Cyl 4.0 L GAS, 8 Cyl 5.0 L GAS
View related parts
Mercury Mountaineer Caliper, Front Passenger Side Part Number: XL2Z-2B120-BA
$45.79 MSRP: $66.65
You Save: $20.86 (32%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Caliper With Pads; Disc Brake Caliper, Front Right; Brake Caliper Repair Kit; Brake Caliper
- Manufacturer Note: Caliper housing - RH - 2001/2002
- Position: Front Passenger Side
- Replaced by: 1U2Z-2V001-TA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1997-2001 Mercury Mountaineer | Base | 6 Cyl 4.0 L GAS, 8 Cyl 5.0 L GAS
View related parts
Mercury Mountaineer Caliper, Front Driver Side Part Number: 6L5Z-2B121-A
Product Specifications
- Other Name: Caliper Assembly - Brake - Less Pad; Disc Brake Caliper, Front Left; Brake Caliper Repair Kit; Caliper Assembly - Brake - Less Pads; Brake Caliper
- Position: Front Driver Side
- Replaces: 1L2Z-2B121-AC, 3L2Z-2B121-BB
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2002-2005 Mercury Mountaineer | Base, Convenience, Luxury, Premier | 6 Cyl 4.0 L FLEX, 6 Cyl 4.0 L GAS, 8 Cyl 4.6 L GAS
View related parts
Mercury Mountaineer Caliper, Front Part Number: 6L5Z-2B120-A
Product Specifications
- Other Name: Caliper Assembly - Brake - Less Pad; Disc Brake Caliper, Front Left, Front Right; Brake Caliper Repair Kit; Caliper Assembly - Brake - Less Pads; Brake Caliper
- Position: Front
- Replaces: 1L2Z-2B120-AB, 3L2Z-2B120-BB
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2002-2005 Mercury Mountaineer | Base, Convenience, Luxury, Premier | 6 Cyl 4.0 L FLEX, 6 Cyl 4.0 L GAS, 8 Cyl 4.6 L GAS
View related parts
Mercury Mountaineer Caliper, Rear Passenger Side Part Number: 6L2Z-2552-A
Product Specifications
- Other Name: Housing; Disc Brake Caliper, Rear Right; Brake Caliper Repair Kit; Brake Caliper
- Manufacturer Note: Warranty Eligible
- Position: Rear Passenger Side
- Replaces: 1L2Z-2552-AA, 1L2Z-2552-BA, 3L2Z-2552-AA, BRCF-181
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2001-2010 Mercury Mountaineer | Base, Convenience, Luxury, Premier | 6 Cyl 4.0 L FLEX, 6 Cyl 4.0 L GAS, 8 Cyl 4.6 L GAS, 8 Cyl 5.0 L GAS
View related parts
Mercury Mountaineer Caliper, Front Passenger Side Part Number: 6L2Z-2B120-A
Product Specifications
- Other Name: Caliper Assembly - Brake; Disc Brake Caliper, Front Right; Brake Caliper Repair Kit; Caliper Assembly - Brake - Less Pads; Brake Caliper
- Position: Front Passenger Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2006-2010 Mercury Mountaineer | Base, Convenience, Luxury, Premier | 6 Cyl 4.0 L GAS, 8 Cyl 4.6 L GAS
View related parts
Mercury Mountaineer Caliper, Front Driver Side Part Number: XL2Z2B121AB
Product Specifications
- Other Name: Caliper Assembly - Brake Lever; Disc Brake Caliper, Front Left; Brake Caliper Repair Kit; Brake Caliper
- Position: Front Driver Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1999-2001 Mercury Mountaineer | Base | 6 Cyl 4.0 L GAS, 8 Cyl 5.0 L GAS
View related parts
Mercury Mountaineer Caliper, Front Passenger Side Part Number: XL2Z-2B120-AB
Product Specifications
- Other Name: Caliper Assembly - Brake; Disc Brake Caliper, Front Right; Brake Caliper Repair Kit; Brake Caliper
- Manufacturer Note: Housing asy. - RH - 1999/ - w/o pads
- Position: Front Passenger Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1999-2001 Mercury Mountaineer | Base | 6 Cyl 4.0 L GAS, 8 Cyl 5.0 L GAS
View related parts
Mercury Mountaineer Caliper, Rear Driver Side Part Number: F57Z-2553-AD
Product Specifications
- Other Name: Housing; Disc Brake Caliper, Rear Left; Brake Caliper Repair Kit; Brake Caliper
- Position: Rear Driver Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1997-2001 Mercury Mountaineer | Base | 6 Cyl 4.0 L GAS, 8 Cyl 5.0 L GAS
View related parts
Mercury Mountaineer Caliper, Rear Passenger Side Part Number: F57Z-2552-AD
Product Specifications
- Other Name: Housing; Disc Brake Caliper, Rear Right; Brake Caliper Repair Kit; Brake Caliper
- Position: Rear Passenger Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 1997-2001 Mercury Mountaineer | Base | 6 Cyl 4.0 L GAS, 8 Cyl 5.0 L GAS
View related parts
Mercury Mountaineer Caliper, Front Driver Side Part Number: 6L2Z-2B121-A
Product Specifications
- Other Name: Caliper Assembly - Brake; Disc Brake Caliper, Front Left; Brake Caliper Repair Kit; Caliper Assembly - Brake - Less Pads; Brake Caliper
- Position: Front Driver Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2006-2010 Mercury Mountaineer | Base, Convenience, Luxury, Premier | 6 Cyl 4.0 L GAS, 8 Cyl 4.6 L GAS
View related parts
Mercury Mountaineer Caliper, Driver Side Part Number: 2C5Z-2553-AA
Product Specifications
- Other Name: Housing; Brake Caliper Repair Kit; Brake Caliper
- Position: Driver Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2002 Mercury Mountaineer | Base | 6 Cyl 4.0 L FLEX, 6 Cyl 4.0 L GAS, 8 Cyl 4.6 L GAS
View related parts
Mercury Mountaineer Caliper, Driver Side Part Number: 1L5Z-2B121-CA
Product Specifications
- Other Name: Caliper Assembly - Brake; Brake Caliper Repair Kit; Brake Caliper; Caliper Assembly - Brake - Less Pads
- Position: Driver Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2001 Mercury Mountaineer | Base | 6 Cyl 4.0 L GAS, 8 Cyl 5.0 L GAS
View related parts
Mercury Mountaineer Caliper, Front Part Number: 1L5Z2B120CA
Product Specifications
- Other Name: Caliper - Front Brakes; Brake Caliper Repair Kit; Brake Caliper; Caliper Assembly - Brake - Less Pads
- Position: Front
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2001 Mercury Mountaineer | Base | 6 Cyl 4.0 L GAS, 8 Cyl 5.0 L GAS
View related parts
Mercury Mountaineer Caliper, Passenger Side Part Number: 2C5Z-2552-AA
Product Specifications
- Other Name: Housing; Brake Caliper Repair Kit; Brake Caliper
- Position: Passenger Side
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2002 Mercury Mountaineer | Base | 6 Cyl 4.0 L FLEX, 6 Cyl 4.0 L GAS, 8 Cyl 4.6 L GAS
View related parts
Mercury Mountaineer Caliper, Rear Driver Side Part Number: 6L2Z-2553-A
Product Specifications
- Other Name: Housing; Disc Brake Caliper, Rear Left; Brake Caliper Repair Kit; Brake Caliper
- Manufacturer Note: Warranty Eligible
- Position: Rear Driver Side
- Replaces: 1L2Z-2553-AA, 1L2Z-2553-BA, 3L2Z-2553-AA, BRCF-13
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following Vehicles:
- 2001-2010 Mercury Mountaineer | Base, Convenience, Luxury, Premier | 6 Cyl 4.0 L FLEX, 6 Cyl 4.0 L GAS, 8 Cyl 4.6 L GAS, 8 Cyl 5.0 L GAS

Mercury Mountaineer Brake Caliper

OEM Brake Caliper boasts unmatched quality. Each part goes through full quality checks. They adhere to Mercury's official factory standards. These steps remove flaws and inconsistencies. So you can get Brake Caliper with long life and a perfect fit. Come to our website and find genuine Mercury Mountaineer parts. We keep a wide inventory of OEM Mountaineer parts at the highly affordable prices. It's easy to search, compare, and pick what you need. You'll love the clear info and simple checkout. We offer top-rated customer service, and we reply fast. We also ship promptly to ensure your order arrives on time.

The Mercury Mountaineer Brake Caliper plays and important role in the braking system, which is quite popular and dependable on different Mountaineer models that have been manufactured since 1996 up to 2010. This Brake Caliper is responsible for translating hydraulic pressure from the master cylinder into mechanical force so that the brake pads make correct contact with the rotors; not only does it translate, it does it in a way that improves efficiency and safety. Mercury Mountaineer's front and rear brakes consist of fixed and floating calipers; the former offer Pistons to exert fixed pressure for all the four calipers; the letter tempo type of calipers provides a floating pistons that change their position, though may cause uneven wear if not well serviced. For this reason, the Mercury Mountaineer Brake Caliper goes for more than a mere tool because it is central to the functionality of the car; thus, contributing to the comfort and efficiency with which the car is driven. For instance, the Brake Caliper is manufactured from robust materials and performance trims are offered that offer light weight solutions along with other attributes so setting this product apart in the automotive marketplace. It is recommended that the Mercury Mountaineer Brake Caliper should be inspected and be checked regularly for any signs of brake drag or fluid leaks to enable the car run as it is supposed to. Any lover of the Mercury Mountaineer would appreciate this part of the car manufacture since it remains a mark of the brand in the SUV market and it is well designed and engineered for effectiveness in its function as a brake caliper.

Mercury Mountaineer Brake Caliper Parts and Q&A

Caliper, Rear Passenger Side
6L2Z-2552-A
Q: How to Properly Disassemble and Assemble a Brake Caliper on Mercury Mountaineer?
A:
Begin the brake caliper service by removing the disc brake caliper then draining all existing brake fluid from it. The caliper gets secured within a vise device before caliper pistons can be removed through a process that requires placing a block of wood between the caliper bridge and pistons while using low air pressure applied to the fluid port. Insert the block removal before extracting the calipers and throwing away both piston seals and boots. It is vital to avoid honing the caliper bores since pistons are unavailable for honed bores along with the requirement for a new disc brake caliper replacement when the bore shows excessive scoring or corrosion. When assembling the brake system do not restore piston seals nor dust boots and stay away from reuse of brake fluid after draining or exposing to open containers beyond an extended period. High Performance DOT 3 Brake Fluid C6AZ-19542-AB alongside a DOT 3 equivalent matching Ford specification ESA-M6C25-A should be used as lubrication for the caliper piston and boot together with piston seal and cylinder bores. Put on the disc brake caliper as the last step of the process.
Caliper, Front Passenger Side
6L2Z-2B120-A
Q: How to service and repair the front brake caliper on Mercury Mountaineer?
A:
Service or repair operations for front brake calipers should start with positioning the vehicle in neutral gear while it rests on a hoist. The correct brake components need permanent protection which requires only using approved DOT 3 motor vehicle brake fluid. The brake hose flow bolt needs removal while placing the brake hose aside with disposal of two copper washers and fluid port capping. The brake caliper sight hole should never be used for piston retraction because it damages their components. The brake caliper guide pin bolts should first be removed along with the brake caliper. The replacement of a new brake caliper becomes necessary in case either leakage or boot damage exists. The installation process begins with a bottom brake caliper bolt located at the top and requires the guide pin brake caliper bolt to be tightened next before mounting the brake caliper and securing guide pin bolts to 72 Nm (53 ft. lbs.). Position the brake hose with two new copper washers before installing the brake hose flow bolt and tightening it to 35 Nm torque. The brake caliper should be bled before performing a normal operational test of the entire braking system. Brake fluid poses a risk to both painted surfaces and plastic materials so surface wash spills right away with water. In case of emergency brake fluid information consult a doctor or dial 1-800-959-3673 to reach Ford/Motorcraft products either in the USA or Canada.