How to service and repair the front antenna cable on 2004 Ford Expedition?

The service process for front antenna lead-in cables begins by first removing the right-hand scuff plate and the right-hand A-pillar lower trim panel. The front antenna lead-in cable service and repair requires detachments of the two pin-type retainers from the lower A-pillar while removing the rear antenna lead-in cable from the front antenna lead-in cable. Replace the antenna cable only through the wiring harness because it cannot function by itself. Cut all free ends to secure the wiring harness from producing unwanted noise. After disconnecting the ground plate proceed to remove the antenna cable ends. The installation process of the new cable needs taping or wire-tying to the wiring harness to minimize noise before proceeding with the reverse removal steps.

OEM 2004 Ford Expedition Antenna Cable

Radio Antenna Cable

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

3 Antenna Cables found

View related parts
2004 Ford Expedition Antenna Cable Part Number: 2L1Z-18812-DA
$16.22 MSRP: $22.07
You Save: $5.85 (27%)
ADD TO CART
Product Specifications
- Other Name: Cable Assembly - Extension; Cable Assembly
- Base No.: 18812B
- Item Weight: 1.00 Pounds
- Item Dimensions: 10.2 x 9.1 x 3.0 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 2L1Z-18812-DA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2004 Ford Expedition Submodels:
- Eddie Bauer, King Ranch, Limited, NBX, XLS, XLT, XLT Sport | 8 Cyl 4.6 L GAS, 8 Cyl 5.4 L GAS
View related parts
2004 Ford Expedition Antenna Cable, Front Part Number: 2L1Z-18812-CB
$13.78 MSRP: $18.75
You Save: $4.97 (27%)
ADD TO CART
Product Specifications
- Other Name: Cable Assembly - Extension; Cable Assembly
- Manufacturer Note: Attaches To Radio Receiver
- Position: Front
- Base No.: 18812A
- Item Weight: 0.50 Pounds
- Item Dimensions: 5.6 x 5.8 x 1.0 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 2L1Z-18812-CB
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2004 Ford Expedition Submodels:
- Eddie Bauer, King Ranch, Limited, NBX, XLS, XLT, XLT Sport | 8 Cyl 4.6 L GAS, 8 Cyl 5.4 L GAS
View related parts
2004 Ford Expedition Antenna Cable Part Number: 2L1Z-18812-EA
Product Specifications
- Other Name: Cable Assembly - Extension; GPS Navigation System Antenna Cable; Cable Assembly
- Base No.: 18812B
- Item Weight: 5.60 Pounds
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 2L1Z-18812-EA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2004 Ford Expedition Submodels:
- Eddie Bauer, King Ranch, Limited, NBX, XLS, XLT, XLT Sport | 8 Cyl 4.6 L GAS, 8 Cyl 5.4 L GAS

2004 Ford Expedition Antenna Cable

If you're seeking quality and affordability, look no further than our extensive inventory of genuine 2004 Ford Expedition Antenna Cable available at FordPartsDeal.com. You can confidently purchase our OEM 2004 Ford Expedition Antenna Cable as they are supported by the manufacturer's warranty and our hassle-free return policy, alongside the benefit of our fast delivery service.

2004 Ford Expedition Antenna Cable Parts Q&A

Q: How to service and repair the front antenna cable on 2004 Ford Expedition?
A: The service process for front antenna lead-in cables begins by first removing the right-hand scuff plate and the right-hand A-pillar lower trim panel. The front antenna lead-in cable service and repair requires detachments of the two pin-type retainers from the lower A-pillar while removing the rear antenna lead-in cable from the front antenna lead-in cable. Replace the antenna cable only through the wiring harness because it cannot function by itself. Cut all free ends to secure the wiring harness from producing unwanted noise. After disconnecting the ground plate proceed to remove the antenna cable ends. The installation process of the new cable needs taping or wire-tying to the wiring harness to minimize noise before proceeding with the reverse removal steps.