How to Service and Repair the Rear Three-Piece Drive Shaft on 2004 Ford F-350 Super Duty?

After raising and supporting the vehicle you should mark the driveshaft position at the axle flange and subsequently disconnect it from this end by removing its bolts and U-joint retaining hardware. The driveshaft needs support from mechanics wire before disconnecting from the coupling shaft by taking out bolts and U-joint retainers which should be discarded and supported again by mechanics wire. Before proceeding with the removal of center bearing support bolts and rear driveshaft assembly make sure to index-mark the driveshaft to the transmission flange or output shaft. Vehicle owners must remove bolts from circular flange sections before discarding them to eventually take out center bearing support bolts and the front driveshaft. To disconnect a slip yoke driveshaft from the transmission you should lower the driveshaft while sliding it backward off the output shaft then insert a plug to stop fluid leakage. Clean all components of driveshaft yoke areas while applying gentle wipe-downs to the bearing and rubber insulator of the driveshaft center bearing without solvent submerging. Thoroughly inspect the universal joint slip yoke boot for all possible tears as well as inspect the driveshaft center bearing support for signs of wear and roughness along with inspecting the center bearing rubber insulator for indications of deterioration. Replace damaged components when found. Vehicles with circular flanges require the installer to align index marks before connecting the transmission-driven front driveshaft through new bolt installation up to hand-tightening. Close the index marks while inserting the driveshaft slip yoke onto the output shaft for vehicles that have this type of equipment. Fit the center support bearing where it should go then install its bolts while just tightening them by hand. Connect the driveshaft to transmission flange bolts and the driveshaft center bearing bolts followed by the installation of the rear driveshaft assembly and its center support bearing bolts which require hand-tightening only. The installation process begins by linking the rear driveshaft to the front driveshaft through new retainers and bolts and following with the connection to the rear axle through additional new retainers and bolts which finally requires tightening of the driveshaft center support bearing bolts.

OEM 2004 Ford F-350 Super Duty Drive Shaft

Axle Shaft

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

53 Drive Shafts found

View related parts
2004 Ford F-350 Super Duty Axle Shaft, Front Driver Side Part Number: 4C3Z-3220-BA
$410.76 MSRP: $603.17
You Save: $192.41 (32%)
ADD TO CART
Product Specifications
- Other Name: Shaft - Front Axle; Axle Shaft Assembly; Axle Assembly
- Position: Front Driver Side
- Replaces: 3C3Z-3220-BA
- Item Weight: 34.90 Pounds
- Item Dimensions: 30.7 x 6.2 x 6.3 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 4C3Z-3220-BA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2004 Ford F-350 Super Duty Submodels:
- Harley-Davidson Edition, King Ranch, Lariat, XL, XLT | 10 Cyl 6.8 L GAS, 8 Cyl 5.4 L GAS, 8 Cyl 6.0 L DIESEL, 8 Cyl 7.3 L DIESEL
View related parts
2004 Ford F-350 Super Duty Axle Shaft, Front Passenger Side Part Number: 4C3Z-3219-BA
$454.45 MSRP: $667.33
You Save: $212.88 (32%)
ADD TO CART
Product Specifications
- Other Name: Shaft - Front Axle; Axle Shaft Assembly; Axle Assembly
- Position: Front Passenger Side
- Replaces: 3C3Z-3219-BA
- Item Weight: 35.40 Pounds
- Item Dimensions: 6.2 x 6.2 x 29.4 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 4C3Z-3219-BA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2004 Ford F-350 Super Duty Submodels:
- Harley-Davidson Edition, King Ranch, Lariat, XL, XLT | 10 Cyl 6.8 L GAS, 8 Cyl 5.4 L GAS, 8 Cyl 6.0 L DIESEL, 8 Cyl 7.3 L DIESEL
View related parts
2004 Ford F-350 Super Duty Drive Shaft Part Number: 3C3Z-4R602-CU
Product Specifications
- Other Name: Shaft Assembly - Drive; Driveshaft
- Replaces: 3C3Z-4R602-CJ
- Base No.: 4R602
- Item Weight: 48.10 Pounds
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 3C3Z-4R602-CU
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2004 Ford F-350 Super Duty Submodels:
- Harley-Davidson Edition, King Ranch, Lariat, XL, XLT | 8 Cyl 6.0 L DIESEL
View related parts
2004 Ford F-350 Super Duty Drive Shaft Part Number: 5C3Z-4A376-A
Product Specifications
- Other Name: Shaft Assembly - Drive; Driveshaft
- Base No.: 4A376
- Item Weight: 35.50 Pounds
- Item Dimensions: 63.0 x 6.3 x 6.2 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 5C3Z-4A376-A
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2004 Ford F-350 Super Duty Submodels:
- Harley-Davidson Edition, King Ranch, Lariat, XL, XLT | 10 Cyl 6.8 L GAS, 8 Cyl 5.4 L GAS
View related parts
2004 Ford F-350 Super Duty Drive Shaft Part Number: 3C3Z-4R602-AJX
Product Specifications
- Other Name: Shaft Assembly - Drive; Driveshaft
- Base No.: 4R602
- Item Weight: 60.50 Pounds
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 3C3Z-4R602-AJX
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2004 Ford F-350 Super Duty Submodels:
- King Ranch, Lariat, XL, XLT | 8 Cyl 6.0 L DIESEL
View related parts
2004 Ford F-350 Super Duty Drive Shaft Part Number: 2C3Z-4602-AA
Product Specifications
- Other Name: Shaft Assembly - Drive; Driveshaft
- Base No.: 4602
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 2C3Z-4602-AA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following 2004 Ford F-350 Super Duty Submodels:
- Harley-Davidson Edition, King Ranch, Lariat, XL, XLT | 10 Cyl 6.8 L GAS
View related parts
2004 Ford F-350 Super Duty Drive Shaft Part Number: 2C3Z-4602-AD
Product Specifications
- Other Name: Shaft Assembly - Drive; Driveshaft
- Base No.: 4602
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 2C3Z-4602-AD
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following 2004 Ford F-350 Super Duty Submodels:
- King Ranch, Lariat, XL, XLT | 8 Cyl 5.4 L GAS
View related parts
2004 Ford F-350 Super Duty Drive Shaft Part Number: 2C3Z-4602-AL
Product Specifications
- Other Name: Shaft Assembly - Drive; Driveshaft
- Base No.: 4602
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 2C3Z-4602-AL
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following 2004 Ford F-350 Super Duty Submodels:
- King Ranch, Lariat, XL, XLT | 8 Cyl 5.4 L GAS
View related parts
2004 Ford F-350 Super Duty Drive Shaft Part Number: 2C3Z-4602-DA
Product Specifications
- Other Name: Shaft Assembly - Drive; Driveshaft
- Base No.: 4602
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 2C3Z-4602-DA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following 2004 Ford F-350 Super Duty Submodels:
- King Ranch, Lariat, XL, XLT | 8 Cyl 5.4 L GAS
View related parts
2004 Ford F-350 Super Duty Drive Shaft Part Number: 2C3Z-4602-EB
Product Specifications
- Other Name: Shaft Assembly - Drive; Driveshaft
- Replaces: 2C3Z-4602-EA
- Base No.: 4602
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 2C3Z-4602-EB
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2004 Ford F-350 Super Duty Submodels:
- Harley-Davidson Edition, King Ranch, Lariat, XL, XLT | 10 Cyl 6.8 L GAS, 8 Cyl 5.4 L GAS
View related parts
2004 Ford F-350 Super Duty Drive Shaft Part Number: 2C3Z-4602-NB
Product Specifications
- Other Name: Shaft Assembly - Drive; Driveshaft
- Replaces: 2C3Z-4602-NA, 2C3Z-4602-XA
- Base No.: 4602
- Item Weight: 41.90 Pounds
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 2C3Z-4602-NB
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2004 Ford F-350 Super Duty Submodels:
- Harley-Davidson Edition, King Ranch, Lariat, XL, XLT | 10 Cyl 6.8 L GAS, 8 Cyl 5.4 L GAS
View related parts
2004 Ford F-350 Super Duty Drive Shaft Part Number: 2C3Z-4602-YA
Product Specifications
- Other Name: Shaft Assembly - Drive; Driveshaft
- Base No.: 4602
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 2C3Z-4602-YA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following 2004 Ford F-350 Super Duty Submodels:
- King Ranch, Lariat, XL, XLT | 8 Cyl 5.4 L GAS
View related parts
2004 Ford F-350 Super Duty Drive Shaft Part Number: 2C3Z-4R602-AY
Product Specifications
- Other Name: Shaft Assembly - Drive; Driveshaft
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 2C3Z-4R602-AY
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following 2004 Ford F-350 Super Duty Submodels:
- King Ranch, Lariat, XL, XLT | 8 Cyl 5.4 L GAS
View related parts
2004 Ford F-350 Super Duty Drive Shaft Part Number: 2C3Z-4R602-BG
Product Specifications
- Other Name: Shaft Assembly - Drive; Driveshaft
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 2C3Z-4R602-BG
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following 2004 Ford F-350 Super Duty Submodels:
- King Ranch, Lariat, XL, XLT | 8 Cyl 5.4 L GAS
View related parts
2004 Ford F-350 Super Duty Drive Shaft Part Number: 2C3Z-4R602-BH
Product Specifications
- Other Name: Shaft Assembly - Drive; Driveshaft
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 2C3Z-4R602-BH
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following 2004 Ford F-350 Super Duty Submodels:
- King Ranch, Lariat, XL, XLT | 8 Cyl 5.4 L GAS
View related parts
2004 Ford F-350 Super Duty Drive Shaft Part Number: 2C3Z-4R602-BK
Product Specifications
- Other Name: Shaft Assembly - Drive; Driveshaft
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 2C3Z-4R602-BK
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following 2004 Ford F-350 Super Duty Submodels:
- King Ranch, Lariat, XL, XLT | 8 Cyl 5.4 L GAS
View related parts
2004 Ford F-350 Super Duty Drive Shaft Part Number: 2C3Z-4R602-BZ
Product Specifications
- Other Name: Shaft Assembly - Drive; Driveshaft
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 2C3Z-4R602-BZ
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following 2004 Ford F-350 Super Duty Submodels:
- Harley-Davidson Edition, King Ranch, Lariat, XL, XLT | 10 Cyl 6.8 L GAS
View related parts
2004 Ford F-350 Super Duty Drive Shaft Part Number: 2C3Z-4R602-CPC
Product Specifications
- Other Name: Shaft Assembly - Drive; Driveshaft
- Replaces: 2C3Z-4R602-CP, 2C3Z-4R602-CPB
- Item Weight: 73.40 Pounds
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 2C3Z-4R602-CPC
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2004 Ford F-350 Super Duty Submodels:
- King Ranch, Lariat, XL, XLT | 8 Cyl 5.4 L GAS
View related parts
2004 Ford F-350 Super Duty Drive Shaft Part Number: 2C3Z-4R602-DDX
Product Specifications
- Other Name: Shaft Assembly - Drive; Driveshaft
- Base No.: 4R602
- Item Weight: 56.70 Pounds
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 2C3Z-4R602-DDX
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2004 Ford F-350 Super Duty Submodels:
- King Ranch, Lariat, XL, XLT | 10 Cyl 6.8 L GAS
View related parts
2004 Ford F-350 Super Duty Drive Shaft Part Number: 2C3Z-4R602-DEC
Product Specifications
- Other Name: Shaft Assembly - Drive; Driveshaft
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 2C3Z-4R602-DEC
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following 2004 Ford F-350 Super Duty Submodels:
- King Ranch, Lariat, XL, XLT | 8 Cyl 5.4 L GAS

| Page 1 of 3 |Next >

1-20 of 53 Results

2004 Ford F-350 Super Duty Drive Shaft

If you're seeking quality and affordability, look no further than our extensive inventory of genuine 2004 Ford F-350 Super Duty Drive Shaft available at FordPartsDeal.com. You can confidently purchase our OEM 2004 Ford F-350 Super Duty Drive Shaft as they are supported by the manufacturer's warranty and our hassle-free return policy, alongside the benefit of our fast delivery service.

2004 Ford F-350 Super Duty Drive Shaft Parts Q&A

Q: How to Service and Repair the Rear Three-Piece Drive Shaft on 2004 Ford F-350 Super Duty?
A: After raising and supporting the vehicle you should mark the driveshaft position at the axle flange and subsequently disconnect it from this end by removing its bolts and U-joint retaining hardware. The driveshaft needs support from mechanics wire before disconnecting from the coupling shaft by taking out bolts and U-joint retainers which should be discarded and supported again by mechanics wire. Before proceeding with the removal of center bearing support bolts and rear driveshaft assembly make sure to index-mark the driveshaft to the transmission flange or output shaft. Vehicle owners must remove bolts from circular flange sections before discarding them to eventually take out center bearing support bolts and the front driveshaft. To disconnect a slip yoke driveshaft from the transmission you should lower the driveshaft while sliding it backward off the output shaft then insert a plug to stop fluid leakage. Clean all components of driveshaft yoke areas while applying gentle wipe-downs to the bearing and rubber insulator of the driveshaft center bearing without solvent submerging. Thoroughly inspect the universal joint slip yoke boot for all possible tears as well as inspect the driveshaft center bearing support for signs of wear and roughness along with inspecting the center bearing rubber insulator for indications of deterioration. Replace damaged components when found. Vehicles with circular flanges require the installer to align index marks before connecting the transmission-driven front driveshaft through new bolt installation up to hand-tightening. Close the index marks while inserting the driveshaft slip yoke onto the output shaft for vehicles that have this type of equipment. Fit the center support bearing where it should go then install its bolts while just tightening them by hand. Connect the driveshaft to transmission flange bolts and the driveshaft center bearing bolts followed by the installation of the rear driveshaft assembly and its center support bearing bolts which require hand-tightening only. The installation process begins by linking the rear driveshaft to the front driveshaft through new retainers and bolts and following with the connection to the rear axle through additional new retainers and bolts which finally requires tightening of the driveshaft center support bearing bolts.