How to Service and Repair the Rear Drive Shaft on 2005 Ford F-350 Super Duty?

Service procedures for the rear three-piece driveshaft begin by properly sustaining the vehicle while you make index marks on the driveshaft at the axle flange before disconnecting it by removing and discarding bolts together with U-Joint retainers. You should support the driveshaft with mechanics wire before you remove its coupling shaft retainers and bolts then discard them with additional support from more mechanics wire. The service proceeds by taking out the support bolts of the center bearing before removing the rear driveshaft assembly while keeping precise records of driveshaft alignment relative to the transmission flange or output shaft position. When dealing with vehicles which utilize a circular flange, remove and throw away all bolts before continuing the process to eliminate the front driveshaft with its center bearing support bolts and remove the disc-shaped flange. Drivers should lower the driveshaft before pushing it backward off the transmission output shaft by plugging the extension housing to avoid fluid leakage. All driveshaft components require cleaning from grease deposits and dirt and rust alongside wiping the bearing and rubber insulator of the center bearing without using solvent immersion. When inspecting the universal joint slip yoke boot, replacement is needed when holes or rips are present while the driveshaft center bearing support requires replacement when wear or rough action occurs. A thorough examination should be done to check for deterioration or cracking and hardness in the center bearing rubber insulator. Replacement is needed if any deficiencies are present. Alignment of index marks allows vehicle installation of the front drive shaft through the transmission via circular flange bolts yet only use hand tightness. Drivers with a vehicle equipped with a slip yoke should align their index marks before inserting the driveshaft slip yoke onto the output shaft. Then they should install the center support bearing followed by hand-tightening the bolts. Position the rear driveshaft assembly before installing center support bearing bolts while applying only hand torque to the bolts. Additionally tighten driveshaft to transmission flange bolts and the driveshaft center bearing bolts. Disassemble the rear driveshaft by connecting it to the front driveshaft while adding new retainers and bolts. Afterward the driver installs the driveshaft to the rear axle and adds new retainers and bolts followed by tightening the center support bearing bolts.

OEM 2005 Ford F-350 Super Duty Drive Shaft

Axle Shaft

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

36 Drive Shafts found

View related parts
2005 Ford F-350 Super Duty Drive Shaft
Part Number: 6C3Z-4602-B
$364.13 MSRP: $503.73
You Save: $139.60 (28%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft Assembly - Drive; Driveshaft
- Replaces: 5C3Z-4602-VB
- Base No.: 4602
- Item Weight: 31.50 Pounds
- Item Dimensions: 25.7 x 6.1 x 15.2 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 6C3Z-4602-B
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2005 Ford F-350 Super Duty Submodels:
- King Ranch, Lariat, XL, XLT | 8 Cyl 5.4 L GAS
View related parts
2005 Ford F-350 Super Duty Drive Shaft
Part Number: 2C3Z-4602-AA
Product Specifications
- Other Name: Shaft Assembly - Drive; Driveshaft
- Base No.: 4602
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 2C3Z-4602-AA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following 2005 Ford F-350 Super Duty Submodels:
- Harley-Davidson Edition, King Ranch, Lariat, XL, XLT | 10 Cyl 6.8 L GAS
View related parts
2005 Ford F-350 Super Duty Drive Shaft
Part Number: 2C3Z-4602-AD
Product Specifications
- Other Name: Shaft Assembly - Drive; Driveshaft
- Base No.: 4602
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 2C3Z-4602-AD
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following 2005 Ford F-350 Super Duty Submodels:
- King Ranch, Lariat, XL, XLT | 8 Cyl 5.4 L GAS
View related parts
2005 Ford F-350 Super Duty Drive Shaft
Part Number: 2C3Z-4602-DA
Product Specifications
- Other Name: Shaft Assembly - Drive; Driveshaft
- Base No.: 4602
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 2C3Z-4602-DA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following 2005 Ford F-350 Super Duty Submodels:
- King Ranch, Lariat, XL, XLT | 8 Cyl 5.4 L GAS
View related parts
2005 Ford F-350 Super Duty Drive Shaft
Part Number: 2C3Z-4602-EB
Product Specifications
- Other Name: Shaft Assembly - Drive; Driveshaft
- Replaces: 2C3Z-4602-EA
- Base No.: 4602
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 2C3Z-4602-EB
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2005 Ford F-350 Super Duty Submodels:
- Harley-Davidson Edition, King Ranch, Lariat, XL, XLT | 10 Cyl 6.8 L GAS, 8 Cyl 5.4 L GAS
View related parts
2005 Ford F-350 Super Duty Drive Shaft
Part Number: 2C3Z-4602-NB
Product Specifications
- Other Name: Shaft Assembly - Drive; Driveshaft
- Replaces: 2C3Z-4602-NA, 2C3Z-4602-XA
- Base No.: 4602
- Item Weight: 41.90 Pounds
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 2C3Z-4602-NB
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2005 Ford F-350 Super Duty Submodels:
- Harley-Davidson Edition, King Ranch, Lariat, XL, XLT | 10 Cyl 6.8 L GAS, 8 Cyl 5.4 L GAS
View related parts
2005 Ford F-350 Super Duty Drive Shaft
Part Number: 2C3Z-4R602-AXX
Product Specifications
- Other Name: Shaft Assembly - Drive; Driveshaft
- Base No.: 4R602
- Item Weight: 58.90 Pounds
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 2C3Z-4R602-AXX
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2005 Ford F-350 Super Duty Submodels:
- King Ranch, Lariat, XL, XLT | 8 Cyl 5.4 L GAS
View related parts
2005 Ford F-350 Super Duty Drive Shaft
Part Number: 2C3Z-4R602-BH
Product Specifications
- Other Name: Shaft Assembly - Drive; Driveshaft
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 2C3Z-4R602-BH
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following 2005 Ford F-350 Super Duty Submodels:
- King Ranch, Lariat, XL, XLT | 8 Cyl 5.4 L GAS
View related parts
2005 Ford F-350 Super Duty Drive Shaft
Part Number: 2C3Z-4R602-BZ
Product Specifications
- Other Name: Shaft Assembly - Drive; Driveshaft
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 2C3Z-4R602-BZ
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following 2005 Ford F-350 Super Duty Submodels:
- Harley-Davidson Edition, King Ranch, Lariat, XL, XLT | 10 Cyl 6.8 L GAS
View related parts
2005 Ford F-350 Super Duty Drive Shaft
Part Number: 2C3Z-4R602-CPC
Product Specifications
- Other Name: Shaft Assembly - Drive; Driveshaft
- Replaces: 2C3Z-4R602-CP, 2C3Z-4R602-CPB
- Item Weight: 73.40 Pounds
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 2C3Z-4R602-CPC
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2005 Ford F-350 Super Duty Submodels:
- King Ranch, Lariat, XL, XLT | 8 Cyl 5.4 L GAS
View related parts
2005 Ford F-350 Super Duty Drive Shaft
Part Number: 2C3Z-4R602-DPX
Product Specifications
- Other Name: Shaft Assembly - Drive; Driveshaft
- Replaces: 2C3Z-4R602-DP
- Base No.: 4R602
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 2C3Z-4R602-DPX
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2005 Ford F-350 Super Duty Submodels:
- Harley-Davidson Edition, King Ranch, Lariat, XL, XLT | 8 Cyl 6.0 L DIESEL
View related parts
2005 Ford F-350 Super Duty Drive Shaft
Part Number: 2C3Z-4R602-DQX
Product Specifications
- Other Name: Shaft Assembly - Drive; Driveshaft
- Replaces: 2C3Z-4R602-DQ
- Base No.: 4R602
- Item Weight: 54.80 Pounds
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 2C3Z-4R602-DQX
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2005 Ford F-350 Super Duty Submodels:
- Harley-Davidson Edition, King Ranch, Lariat, XL, XLT | 10 Cyl 6.8 L GAS, 8 Cyl 5.4 L GAS
View related parts
2005 Ford F-350 Super Duty Drive Shaft
Part Number: 2C3Z-4R602-DSX
Product Specifications
- Other Name: Shaft Assembly - Drive; Driveshaft
- Base No.: 4R602
- Item Weight: 60.50 Pounds
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 2C3Z-4R602-DSX
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2005 Ford F-350 Super Duty Submodels:
- King Ranch, Lariat, XL, XLT | 8 Cyl 5.4 L GAS
View related parts
2005 Ford F-350 Super Duty Drive Shaft
Part Number: 2C3Z-4R602-DUX
Product Specifications
- Other Name: Shaft Assembly - Drive; Driveshaft
- Base No.: 4R602
- Item Weight: 57.20 Pounds
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 2C3Z-4R602-DUX
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2005 Ford F-350 Super Duty Submodels:
- Harley-Davidson Edition, King Ranch, Lariat, XL, XLT | 10 Cyl 6.8 L GAS, 8 Cyl 6.0 L DIESEL
View related parts
2005 Ford F-350 Super Duty Drive Shaft
Part Number: 2C3Z-4R602-ED
Product Specifications
- Other Name: Shaft Assembly - Drive; Driveshaft
- Item Weight: 60.00 Pounds
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 2C3Z-4R602-ED
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following 2005 Ford F-350 Super Duty Submodels:
- Harley-Davidson Edition, King Ranch, Lariat, XL, XLT | 10 Cyl 6.8 L GAS
View related parts
2005 Ford F-350 Super Duty Drive Shaft
Part Number: 2C3Z-4R602-PC
Product Specifications
- Other Name: Shaft Assembly - Drive; Driveshaft
- Base No.: 4R602
- Item Weight: 68.30 Pounds
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 2C3Z-4R602-PC
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2005 Ford F-350 Super Duty Submodels:
- King Ranch, Lariat, XL, XLT | 8 Cyl 5.4 L GAS
View related parts
2005 Ford F-350 Super Duty Drive Shaft
Part Number: 3C3Z-4602-AM
Product Specifications
- Other Name: Shaft Assembly - Drive; Driveshaft
- Base No.: 4602
- Item Weight: 36.40 Pounds
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 3C3Z-4602-AM
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2005 Ford F-350 Super Duty Submodels:
- Harley-Davidson Edition, King Ranch, Lariat, XL, XLT | 8 Cyl 6.0 L DIESEL
View related parts
2005 Ford F-350 Super Duty Drive Shaft
Part Number: 3C3Z-4602-AR
Product Specifications
- Other Name: Shaft Assembly - Drive; Driveshaft
- Replaces: 3C3Z-4602-AH
- Base No.: 4602
- Item Weight: 32.40 Pounds
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 3C3Z-4602-AR
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2005 Ford F-350 Super Duty Submodels:
- King Ranch, Lariat, XL, XLT | 8 Cyl 5.4 L GAS
View related parts
2005 Ford F-350 Super Duty Drive Shaft
Part Number: 3C3Z-4602-BB
Product Specifications
- Other Name: Shaft Assembly - Drive; Driveshaft
- Replaces: 3C3Z-4602-BA
- Base No.: 4602
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 3C3Z-4602-BB
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2005 Ford F-350 Super Duty Submodels:
- Harley-Davidson Edition, King Ranch, Lariat, XL, XLT | 8 Cyl 5.4 L GAS, 8 Cyl 6.0 L DIESEL
View related parts
2005 Ford F-350 Super Duty Drive Shaft
Part Number: 3C3Z-4R602-BPX
Product Specifications
- Other Name: Shaft Assembly - Drive; Driveshaft
- Replaces: 3C3Z-4R602-BP
- Base No.: 4R602
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 3C3Z-4R602-BPX
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2005 Ford F-350 Super Duty Submodels:
- Harley-Davidson Edition, King Ranch, Lariat, XL, XLT | 8 Cyl 6.0 L DIESEL

| Page 1 of 2 |Next >

1-20 of 36 Results

2005 Ford F-350 Super Duty Drive Shaft

If you're seeking quality and affordability, look no further than our extensive inventory of genuine 2005 Ford F-350 Super Duty Drive Shaft available at FordPartsDeal.com. You can confidently purchase our OEM 2005 Ford F-350 Super Duty Drive Shaft as they are supported by the manufacturer's warranty and our hassle-free return policy, alongside the benefit of our fast delivery service.

2005 Ford F-350 Super Duty Drive Shaft Parts Questions & Experts Answers

Q: How to Service and Repair the Rear Drive Shaft on 2005 Ford F-350 Super Duty?
A: Service procedures for the rear three-piece driveshaft begin by properly sustaining the vehicle while you make index marks on the driveshaft at the axle flange before disconnecting it by removing and discarding bolts together with U-Joint retainers. You should support the driveshaft with mechanics wire before you remove its coupling shaft retainers and bolts then discard them with additional support from more mechanics wire. The service proceeds by taking out the support bolts of the center bearing before removing the rear driveshaft assembly while keeping precise records of driveshaft alignment relative to the transmission flange or output shaft position. When dealing with vehicles which utilize a circular flange, remove and throw away all bolts before continuing the process to eliminate the front driveshaft with its center bearing support bolts and remove the disc-shaped flange. Drivers should lower the driveshaft before pushing it backward off the transmission output shaft by plugging the extension housing to avoid fluid leakage. All driveshaft components require cleaning from grease deposits and dirt and rust alongside wiping the bearing and rubber insulator of the center bearing without using solvent immersion. When inspecting the universal joint slip yoke boot, replacement is needed when holes or rips are present while the driveshaft center bearing support requires replacement when wear or rough action occurs. A thorough examination should be done to check for deterioration or cracking and hardness in the center bearing rubber insulator. Replacement is needed if any deficiencies are present. Alignment of index marks allows vehicle installation of the front drive shaft through the transmission via circular flange bolts yet only use hand tightness. Drivers with a vehicle equipped with a slip yoke should align their index marks before inserting the driveshaft slip yoke onto the output shaft. Then they should install the center support bearing followed by hand-tightening the bolts. Position the rear driveshaft assembly before installing center support bearing bolts while applying only hand torque to the bolts. Additionally tighten driveshaft to transmission flange bolts and the driveshaft center bearing bolts. Disassemble the rear driveshaft by connecting it to the front driveshaft while adding new retainers and bolts. Afterward the driver installs the driveshaft to the rear axle and adds new retainers and bolts followed by tightening the center support bearing bolts.