Other Name: Bulb; Center High Mount Stop Light, Rear; Engine Compartment, Back Up, Turn Signal; Parking, Dome, Interior, Tail, Car; Backup Lamp Bulb; Dome Lamp Bulb; Parking Lamp Bulb; High Mount Bulb; Exterior Bulbs.
Position: Rear
Base No.: 13466
Item Weight: 0.30 Pounds
Item Dimensions: 0.4 x 0.4 x 1.1 inches
Condition: New
Fitment Type: Direct Replacement
SKU: D7TZ-13466-A
Warranty: This genuine part is guaranteed by Ford's
factory warranty.
More Info
Fits the following 2004 Lincoln Town Car Submodels:
Anniversary, Base, Cartier, Cartier L, Cypress, Executive, Executive L, Executive Protection Series, Jack Nicklaus, Protection Series, Signature, Signature L, Signature Limited, Touring Edition, Tournament Edition, Ultimate, Ultimate L | 8 Cyl 4.6 L GAS, 8 Cyl 5.0 L GAS
Other Name: Bulb; Turn Signal & Parking Light Bulb, Front; Side Marker Light; Headlight Bulbs; Car Bulbs; Parking Lamp Bulb; Signal Bulb; Exterior Bulbs
Position: Front
Replaces: F5DZ-13466-A
Base No.: 13466
Item Weight: 0.40 Pounds
Condition: New
Fitment Type: Direct Replacement
SKU: YU5Z-13466-AD
Warranty: This genuine part is guaranteed by Ford's
factory warranty.
More Info
Fits the following 2004 Lincoln Town Car Submodels:
Anniversary, Base, Cartier, Cartier L, Cypress, Designer Series, Executive, Executive L, Executive Protection Series, Protection Series, Signature, Signature L, Signature Limited, Touring Edition, Ultimate, Ultimate L | 8 Cyl 4.6 L FLEX, 8 Cyl 4.6 L GAS
Other Name: Bulb, Turn Signal & Parking, Tail, Backup, License Plate, Side Marker, Headlight; Backup Lamp Bulb; Signal, Parking, Stop, High Mount, Cornering, License, and Parking Light Bulbs.
Position: Lower Outer
Replaces: F8DZ-13466-AB, E8AZ-13466-A
Base No.: 13466
Item Weight: 0.40 Pounds
Item Dimensions: 0.4 x 0.4 x 1.0 inches
Condition: New
Fitment Type: Direct Replacement
SKU: F5DZ-13466-B
Warranty: This genuine part is guaranteed by Ford's
factory warranty.
More Info
Fits the following 2004 Lincoln Town Car Submodels:
Anniversary, Base, Cartier, Cartier L, Cypress, Designer Series, Executive, Executive L, Executive Protection Series, Jack Nicklaus, Protection Series, Signature, Signature L, Signature Limited, Signature SE, Touring Edition, Tournament Edition, Ultimate, Ultimate L | 8 Cyl 4.6 L FLEX, 8 Cyl 4.6 L GAS, 8 Cyl 5.0 L GAS
2004 Lincoln Town Car Headlight Bulb
If you're seeking quality and affordability, look no further than our extensive inventory of genuine 2004 Lincoln Town Car Headlight Bulb available at FordPartsDeal.com. You can confidently purchase our OEM 2004 Lincoln Town Car Headlight Bulb as they are supported by the manufacturer's warranty and our hassle-free return policy, alongside the benefit of our fast delivery service.
2004 Lincoln Town Car Headlight Bulb Parts Questions & Experts Answers
Q: How to service the headlight bulb on 2004 Lincoln Town Car?
A: First touch the halogen bulb only at its base to stop shattering because it holds compressed gas. It is essential to leave the headlamp bulb installed until new replacement time to stop contaminants from entering and affecting operational quality. The service requires you to verify that you have switched off both headlamp switch and ignition switch. The service procedure starts with unfastening the three pin-type retainers and two screws and the radiator air deflector while also detaching the electrical connector and bolts from the headlamp assembly. You need to detach the protective cover of the headlamp bulb using its bolts. On the standard low beam bulb installation requires disconnecting the electrical connector before bulb removal. Detach the HID low beam bulb by releasing spring tabs as well as disconnecting the electrical connector before removing it. The high beam bulb requires disconnecting its electrical connector before removing it. Installations require connecting the high beam bulb and electrical connector followed by mounting the HID low beam bulb with spring tabs while connecting its electrical connector and finally attaching the low beam bulb along with its electrical connector. Install the headlamp bulb protective cover after tightening the bolts through three steps: start by threading the bolts partially then center the gasket correctly before completing bolt tightening. Reposition the headlamp assembly with its bolts before reconnecting electrical wires then secure the three pin-type retainers, two screws and radiator air deflector. The final step involves possible adjustment of headlamps.