Other Name: Bulb; Center High Mount Stop Light, Rear; Engine Compartment, Back Up, Turn Signal; Parking, Dome, Interior, Tail, Car; Backup Lamp Bulb; Dome Lamp Bulb; Parking Lamp Bulb; High Mount Bulb; Exterior Bulbs.
Position: Rear
Base No.: 13466
Item Weight: 0.30 Pounds
Item Dimensions: 0.4 x 0.4 x 1.1 inches
Condition: New
Fitment Type: Direct Replacement
SKU: D7TZ-13466-A
Warranty: This genuine part is guaranteed by Ford's
factory warranty.
More Info
Fits the following 2005 Lincoln Town Car Submodels:
Anniversary, Base, Cartier, Cartier L, Cypress, Executive, Executive L, Executive Protection Series, Jack Nicklaus, Protection Series, Signature, Signature L, Signature Limited, Touring Edition, Tournament Edition, Ultimate, Ultimate L | 8 Cyl 4.6 L GAS, 8 Cyl 5.0 L GAS
Other Name: Bulb; Turn Signal & Parking Light Bulb, Front; Side Marker Light; Headlight Bulbs; Car Bulbs; Parking Lamp Bulb; Signal Bulb; Exterior Bulbs
Position: Front
Replaces: F5DZ-13466-A
Base No.: 13466
Item Weight: 0.40 Pounds
Condition: New
Fitment Type: Direct Replacement
SKU: YU5Z-13466-AD
Warranty: This genuine part is guaranteed by Ford's
factory warranty.
More Info
Fits the following 2005 Lincoln Town Car Submodels:
Anniversary, Base, Cartier, Cartier L, Cypress, Designer Series, Executive, Executive L, Executive Protection Series, Protection Series, Signature, Signature L, Signature Limited, Touring Edition, Ultimate, Ultimate L | 8 Cyl 4.6 L FLEX, 8 Cyl 4.6 L GAS
Other Name: Bulb, Turn Signal & Parking, Tail, Backup, License Plate, Side Marker, Headlight; Backup Lamp Bulb; Signal, Parking, Stop, High Mount, Cornering, License, and Parking Light Bulbs.
Position: Lower Outer
Replaces: F8DZ-13466-AB, E8AZ-13466-A
Base No.: 13466
Item Weight: 0.40 Pounds
Item Dimensions: 0.4 x 0.4 x 1.0 inches
Condition: New
Fitment Type: Direct Replacement
SKU: F5DZ-13466-B
Warranty: This genuine part is guaranteed by Ford's
factory warranty.
More Info
Fits the following 2005 Lincoln Town Car Submodels:
Anniversary, Base, Cartier, Cartier L, Cypress, Designer Series, Executive, Executive L, Executive Protection Series, Jack Nicklaus, Protection Series, Signature, Signature L, Signature Limited, Signature SE, Touring Edition, Tournament Edition, Ultimate, Ultimate L | 8 Cyl 4.6 L FLEX, 8 Cyl 4.6 L GAS, 8 Cyl 5.0 L GAS
2005 Lincoln Town Car Headlight Bulb
If you're seeking quality and affordability, look no further than our extensive inventory of genuine 2005 Lincoln Town Car Headlight Bulb available at FordPartsDeal.com. You can confidently purchase our OEM 2005 Lincoln Town Car Headlight Bulb as they are supported by the manufacturer's warranty and our hassle-free return policy, alongside the benefit of our fast delivery service.
2005 Lincoln Town Car Headlight Bulb Parts Q&A
Q: How to service the front headlight bulb on 2005 Lincoln Town Car?
A: Service of the headlamp bulb requires beginning with the off positions of both the headlamp switch and ignition switch. Begin service by disconnecting the three pin-type retainers and two screws and the radiator air deflector followed by the bolts securing the headlamp assembly. Users must detach the electrical plug followed by unthreading the screws which allows them to remove the headlamp bulb protective cover. Disconnection of the electrical connector along with bulb removal completes the standard low beam bulb service. When dealing with HID low beam bulbs the spring tabs need release followed by disconnecting the electrical connector before bulb removal. The removal process for the high beam bulb starts by disconnecting its electrical connector. Begin the installation process by placing the high beam bulb into position then connect the electrical connector to it. Next install the HID low beam bulb by using spring tabs for support then link its electrical connector. Proceed to install the standard low beam bulb while you connect its electrical connector. Follow these steps to replace the headlamp bulb protective cover and bolts by partially threading the bolts at first then checking gasket placement before finishing the bolt tightening process. Renew the headlamp assembly along with bolts while connecting the electrical connector followed by installing three pin-type retainers and two screws together with the radiator air deflector then adjust the headlamps if required.