FordParts
My Garage
My Account
Cart
OEM 2005 Ford E-250 Intake Manifold
Engine Intake Manifold- Select Vehicle by Model
- Select Vehicle by VIN
Select Vehicle by Model
orMake
Model
Year
Select Vehicle by VIN
For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).
3 Intake Manifolds found
2005 Ford E-250 Intake Manifold Part Number: 4C2Z-9424-CA
Product Specifications- Other Name: Manifold Assembly - Inlet; Lower Manifold
- Base No.: 9424
- Item Weight: 21.40 Pounds
- Item Dimensions: 22.1 x 19.8 x 12.9 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 4C2Z-9424-CA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
2005 Ford E-250 Intake Manifold, Lower Part Number: 5L3Z-9424-BB
Product Specifications- Other Name: Manifold Assembly - Inlet; Engine Intake Manifold, Lower
- Position: Lower
- Base No.: 9424B
- Item Weight: 6.80 Pounds
- Item Dimensions: 20.0 x 16.2 x 11.0 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 5L3Z-9424-BB
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
2005 Ford E-250 Intake Manifold, Upper Part Number: 3L3Z-9424-DA
Product Specifications- Other Name: Manifold Assembly - Inlet; Engine Intake Manifold, Upper; Intake Plenum
- Manufacturer Note: Upper, FROM 12/9/2002
- Position: Upper
- Base No.: 9424
- Item Weight: 15.80 Pounds
- Item Dimensions: 19.9 x 16.9 x 10.0 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 3L3Z-9424-DA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
2005 Ford E-250 Intake Manifold
If you're seeking quality and affordability, look no further than our extensive inventory of genuine 2005 Ford E-250 Intake Manifold available at FordPartsDeal.com. You can confidently purchase our OEM 2005 Ford E-250 Intake Manifold as they are supported by the manufacturer's warranty and our hassle-free return policy, alongside the benefit of our fast delivery service.
2005 Ford E-250 Intake Manifold Parts Q&A
- Q: How to install the intake manifold and its components on 2005 Ford E-250?A: First step to install the intake manifold involves placing intake manifold gaskets with the intake manifold before conducting bolt installation in a loose manner. Before proceeding with installation apply the thermostat housing to the engine block before placing the thermostat and a new O-ring seal. The therapist housing bolts need sequence tightening with intake manifold bolts because you must first loosely install the bolts on the thermostat housing and then perform two stages of tightening: 2 Nm (18 inch lbs.) followed by 25 Nm (18 ft. lbs.). Starting from the intake manifold bracket attach the pushpin retainer while adding the screws and 10 coils afterward move the LH fuel charge wiring harness into place before securing it with bolts. Fitting the RH fuel charging wiring harness requires stud bolts followed by adjustment of the transmission fluid level indicator tube and fitting the retaining nut. Fit together the 10 ignition coil electrical connectors, 10 fuel injector electrical connectors, FRP sensor electrical connector and vacuum connector with the coolant hose. Professional technicians should apply the throttle body adapter gasket first to the assembly before tightening the bolts in two sequence: starting at 9 Nm (80 inch lbs.) then adding an additional 90-degree (1/4 turn). Ensure a secure connection of the brake booster with evaporative emission hose and Positive Crankcase Ventilation (PCV) coolant hose together with heated PCV tube and engine vacuum harness and Throttle Position (TP) sensor electrical connector with its red clip pushed in place. After connecting the electronic Throttle Body (TB) electrical connector with its red clip and installing an upper radiator hose you should connect the fuel hose spring lock couplings. The generator installation requires ground battery cable connection after which the engine cover goes on and the assembly of air cleaner components follows before cooling system filling.