How to Service and Repair Automatic Transmission Shift Levers on 2005 Ford Escape?

A transmission automatic transmission shift lever requires servicing by first placing the automobile into neutral position on a hoist. You should start by placing the floor shift automatic transmission shift lever into (D) mode before using a pick to elevate the upper shift lever trim ring so you can proceed to detach the top finish panel. Disconnect the shift cable by detaching the end of the cable from the gearshift lever as well as removing it from the supporting bracket. Begin by taking out the shifter through a process of disconnecting electric wires and unscrewing four bolts. Start by installing the shifter assembly while tightening its 4 bolts to 25 Nm (18 ft. lbs.) before reconnecting the electrical connector. To complete the installation you should start with the upper center console assembly followed by the upper shift lever trim ring while paying attention to properly position the thick tab on the driver side front of the shifter before pressing it into position. Finish the process by readjusting the shift cable.

OEM 2005 Ford Escape Automatic Transmission Shift Levers

Automatic Transmission Shifter

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

3 Automatic Transmission Shift Levers found

View related parts
2005 Ford Escape Gear Shift Assembly Part Number: 5L8Z-7210-EA
$77.52 MSRP: $112.83
You Save: $35.31 (32%)
ADD TO CART
Product Specifications
- Other Name: Housing Assembly - Gear Shift
- Base No.: 7210B
- Item Weight: 3.80 Pounds
- Item Dimensions: 14.5 x 13.9 x 7.5 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 5L8Z-7210-EA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2005 Ford Escape Submodels:
- Hybrid, Limited, XLS, XLT, XLT No Boundaries, XLT Sport | 4 Cyl 2.0 L GAS, 4 Cyl 2.3 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.3 L GAS, 6 Cyl 3.0 L GAS
View related parts
2005 Ford Escape Gear Shift Assembly Part Number: 5L8Z-7210-AA
Product Specifications
- Other Name: Lever - Transmission Gear Shift
- Manufacturer Note: Gearshift Lever
- Base No.: 7210
- Item Weight: 3.60 Pounds
- Item Dimensions: 18.0 x 11.2 x 7.3 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 5L8Z-7210-AA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2005 Ford Escape Submodels:
- Hybrid, Limited, XLS, XLT, XLT No Boundaries, XLT Sport | 4 Cyl 2.3 L FULL HYBRID EV-GAS (FHEV), 4 Cyl 2.3 L GAS, 6 Cyl 3.0 L GAS
View related parts
2005 Ford Escape Shifter Assembly Part Number: 5M6Z-7210-C
Product Specifications
- Other Name: Lever - Gear Shift; Automatic Transmission Shift Lever; Shift Lever
- Base No.: 7210
- Item Weight: 4.90 Pounds
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 5M6Z-7210-C
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2005 Ford Escape Submodels:
- Hybrid | 4 Cyl 2.3 L FULL HYBRID EV-GAS (FHEV)

2005 Ford Escape Automatic Transmission Shift Levers

If you're seeking quality and affordability, look no further than our extensive inventory of genuine 2005 Ford Escape Automatic Transmission Shift Levers available at FordPartsDeal.com. You can confidently purchase our OEM 2005 Ford Escape Automatic Transmission Shift Levers as they are supported by the manufacturer's warranty and our hassle-free return policy, alongside the benefit of our fast delivery service.

2005 Ford Escape Automatic Transmission Shift Levers Parts Q&A

Q: How to Service and Repair Automatic Transmission Shift Levers on 2005 Ford Escape?
A: A transmission automatic transmission shift lever requires servicing by first placing the automobile into neutral position on a hoist. You should start by placing the floor shift automatic transmission shift lever into (D) mode before using a pick to elevate the upper shift lever trim ring so you can proceed to detach the top finish panel. Disconnect the shift cable by detaching the end of the cable from the gearshift lever as well as removing it from the supporting bracket. Begin by taking out the shifter through a process of disconnecting electric wires and unscrewing four bolts. Start by installing the shifter assembly while tightening its 4 bolts to 25 Nm (18 ft. lbs.) before reconnecting the electrical connector. To complete the installation you should start with the upper center console assembly followed by the upper shift lever trim ring while paying attention to properly position the thick tab on the driver side front of the shifter before pressing it into position. Finish the process by readjusting the shift cable.