How to Service and Repair the Rear One-Piece Drive Shaft for 4X2 on 2005 Ford F-250 Super Duty?

Begin front driveshaft service and repair of 4x2 vehicles by hoisting the vehicle so its transmission is set to neutral. Rephrase the driveshaft to the transmission extension housing by making index marks for vehicles that use slip yokes to prevent output shaft rotation. The circular flange service requires marking both the driveshaft yoke and the transmission flange but split pin yoke vehicles need index-marking of the driveshaft and rear axle pinion flange. Use a wrench to remove and discard the four bolts and two u-joint retainers from split pin yoke vehicles and release four bolts only on circular flange vehicles with different bolt directions based on application requirements. Driveshaft separation should occur at the rear axle pinion flange position on automatic transmissions along with a removal of the manual transmission driveshaft or its sliding distance backward off the output shaft. Stick the bearing cups onto the spider and close the automatic transmission extension housing with a plug to stop fluid leakage. The slip-yoke spline of vehicles with slip yokes needs grease during installation and the extension housing plug removal should occur at the same time as slip-yoke transmission output shaft alignment for driveshaft installation. Circular flange vehicles require that the driveshaft yoke be placed on the transmission flange where index marks should align and new bolts should be installed with care for their directions. When working on split pin flange vehicles personnel must first remove tape from bearing cups before they line up the index marks while placing these cups into the rear axle pinion flange. You should install loose four bolts on the circular flange yoke for the driveshaft at the rear axle pinion flange and follow a cross pattern to achieve proper seating. The process for split pin yoke vehicles requires installation of two new retainers followed by four new bolts before lowering the vehicle.

OEM 2005 Ford F-250 Super Duty Drive Shaft

Axle Shaft

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

39 Drive Shafts found

View related parts
2005 Ford F-250 Super Duty Axle Shaft, Front Driver Side Part Number: 4C3Z-3220-BA
$410.76 MSRP: $603.17
You Save: $192.41 (32%)
ADD TO CART
Product Specifications
- Other Name: Shaft - Front Axle; Axle Shaft Assembly; Axle Assembly
- Position: Front Driver Side
- Replaces: 3C3Z-3220-BA
- Item Weight: 34.90 Pounds
- Item Dimensions: 30.7 x 6.2 x 6.3 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 4C3Z-3220-BA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2005 Ford F-250 Super Duty Submodels:
- Harley-Davidson Edition, King Ranch, Lariat, XL, XLT | 10 Cyl 6.8 L GAS, 8 Cyl 5.4 L GAS, 8 Cyl 6.0 L DIESEL, 8 Cyl 7.3 L DIESEL
View related parts
2005 Ford F-250 Super Duty Axle Shaft, Front Passenger Side Part Number: 4C3Z-3219-BA
$454.45 MSRP: $667.33
You Save: $212.88 (32%)
ADD TO CART
Product Specifications
- Other Name: Shaft - Front Axle; Axle Shaft Assembly; Axle Assembly
- Position: Front Passenger Side
- Replaces: 3C3Z-3219-BA
- Item Weight: 35.40 Pounds
- Item Dimensions: 6.2 x 6.2 x 29.4 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 4C3Z-3219-BA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2005 Ford F-250 Super Duty Submodels:
- Harley-Davidson Edition, King Ranch, Lariat, XL, XLT | 10 Cyl 6.8 L GAS, 8 Cyl 5.4 L GAS, 8 Cyl 6.0 L DIESEL, 8 Cyl 7.3 L DIESEL
View related parts
2005 Ford F-250 Super Duty Drive Shaft Part Number: 6C3Z-4602-B
$364.13 MSRP: $503.73
You Save: $139.60 (28%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft Assembly - Drive; Driveshaft
- Replaces: 5C3Z-4602-VB
- Base No.: 4602
- Item Weight: 31.50 Pounds
- Item Dimensions: 25.7 x 6.1 x 15.2 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 6C3Z-4602-B
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2005 Ford F-250 Super Duty Submodels:
- King Ranch, Lariat, XL, XLT | 10 Cyl 6.8 L GAS, 8 Cyl 5.4 L GAS
View related parts
2005 Ford F-250 Super Duty Drive Shaft Part Number: 8C3Z-4R602-EEA
Product Specifications
- Other Name: Shaft Assembly - Drive; Driveshaft
- Replaces: 3C3Z-4R602-EG
- Base No.: 4R602
- Item Weight: 53.50 Pounds
- Item Dimensions: 82.4 x 10.5 x 8.5 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 8C3Z-4R602-EEA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2005 Ford F-250 Super Duty Submodels:
- Harley-Davidson Edition, King Ranch, Lariat, XL, XLT | 10 Cyl 6.8 L GAS
View related parts
2005 Ford F-250 Super Duty Drive Shaft, Rear Part Number: 2C3Z-4R602-FPC
Product Specifications
- Other Name: Shaft Assembly - Drive; Driveshaft
- Position: Rear
- Replaces: 2C3Z-4R602-FPB
- Item Weight: 39.10 Pounds
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 2C3Z-4R602-FPC
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2005 Ford F-250 Super Duty Submodels:
- King Ranch, Lariat, XL, XLT | 8 Cyl 5.4 L GAS
View related parts
2005 Ford F-250 Super Duty Drive Shaft Part Number: 2C3Z-4R602-AXX
Product Specifications
- Other Name: Shaft Assembly - Drive; Driveshaft
- Base No.: 4R602
- Item Weight: 58.90 Pounds
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 2C3Z-4R602-AXX
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2005 Ford F-250 Super Duty Submodels:
- King Ranch, Lariat, XL, XLT | 8 Cyl 5.4 L GAS
View related parts
2005 Ford F-250 Super Duty Drive Shaft Part Number: 2C3Z-4R602-BDD
Product Specifications
- Other Name: Shaft Assembly - Drive; Driveshaft
- Base No.: 4R602
- Item Weight: 58.60 Pounds
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 2C3Z-4R602-BDD
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2005 Ford F-250 Super Duty Submodels:
- King Ranch, Lariat, XL, XLT | 10 Cyl 6.8 L GAS, 8 Cyl 5.4 L GAS
View related parts
2005 Ford F-250 Super Duty Drive Shaft Part Number: 2C3Z-4R602-BH
Product Specifications
- Other Name: Shaft Assembly - Drive; Driveshaft
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 2C3Z-4R602-BH
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following 2005 Ford F-250 Super Duty Submodels:
- King Ranch, Lariat, XL, XLT | 8 Cyl 5.4 L GAS
View related parts
2005 Ford F-250 Super Duty Drive Shaft Part Number: 2C3Z-4R602-BR
Product Specifications
- Other Name: Shaft Assembly - Drive; Driveshaft
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 2C3Z-4R602-BR
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following 2005 Ford F-250 Super Duty Submodels:
- Harley-Davidson Edition, King Ranch, Lariat, XL, XLT | 10 Cyl 6.8 L GAS
View related parts
2005 Ford F-250 Super Duty Drive Shaft Part Number: 2C3Z-4R602-DEC
Product Specifications
- Other Name: Shaft Assembly - Drive; Driveshaft
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 2C3Z-4R602-DEC
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following 2005 Ford F-250 Super Duty Submodels:
- King Ranch, Lariat, XL, XLT | 8 Cyl 5.4 L GAS
View related parts
2005 Ford F-250 Super Duty Drive Shaft Part Number: 2C3Z-4R602-DQX
Product Specifications
- Other Name: Shaft Assembly - Drive; Driveshaft
- Replaces: 2C3Z-4R602-DQ
- Base No.: 4R602
- Item Weight: 54.80 Pounds
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 2C3Z-4R602-DQX
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2005 Ford F-250 Super Duty Submodels:
- King Ranch, Lariat, XL, XLT | 8 Cyl 5.4 L GAS
View related parts
2005 Ford F-250 Super Duty Drive Shaft Part Number: 2C3Z-4R602-EEX
Product Specifications
- Other Name: Shaft Assembly - Drive; Driveshaft
- Replaces: 2C3Z-4R602-EE
- Base No.: 4R602
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 2C3Z-4R602-EEX
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2005 Ford F-250 Super Duty Submodels:
- Harley-Davidson Edition, King Ranch, Lariat, XL, XLT | 10 Cyl 6.8 L GAS, 8 Cyl 5.4 L GAS, 8 Cyl 6.0 L DIESEL
View related parts
2005 Ford F-250 Super Duty Drive Shaft Part Number: 2C3Z-4R602-EW
Product Specifications
- Other Name: Shaft Assembly - Drive; Driveshaft
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 2C3Z-4R602-EW
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following 2005 Ford F-250 Super Duty Submodels:
- Harley-Davidson Edition, King Ranch, Lariat, XL, XLT | 10 Cyl 6.8 L GAS
View related parts
2005 Ford F-250 Super Duty Drive Shaft Part Number: 2C3Z-4R602-FBC
Product Specifications
- Other Name: Shaft Assembly - Drive; Driveshaft
- Replaces: 2C3Z-4R602-FBB
- Item Weight: 58.30 Pounds
- Item Dimensions: 25.2 x 6.2 x 15.6 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 2C3Z-4R602-FBC
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2005 Ford F-250 Super Duty Submodels:
- King Ranch, Lariat, XL, XLT | 8 Cyl 5.4 L GAS
View related parts
2005 Ford F-250 Super Duty Drive Shaft Part Number: 2C3Z-4R602-FC
Product Specifications
- Other Name: Shaft Assembly - Drive; Driveshaft
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 2C3Z-4R602-FC
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following 2005 Ford F-250 Super Duty Submodels:
- Harley-Davidson Edition, King Ranch, Lariat, XL, XLT | 10 Cyl 6.8 L GAS
View related parts
2005 Ford F-250 Super Duty Drive Shaft Part Number: 2C3Z-4R602-FX
Product Specifications
- Other Name: Shaft Assembly - Drive; Driveshaft
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 2C3Z-4R602-FX
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following 2005 Ford F-250 Super Duty Submodels:
- King Ranch, Lariat, XL, XLT | 8 Cyl 5.4 L GAS
View related parts
2005 Ford F-250 Super Duty Drive Shaft Part Number: 2C3Z-4R602-PC
Product Specifications
- Other Name: Shaft Assembly - Drive; Driveshaft
- Base No.: 4R602
- Item Weight: 68.30 Pounds
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 2C3Z-4R602-PC
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2005 Ford F-250 Super Duty Submodels:
- King Ranch, Lariat, XL, XLT | 8 Cyl 5.4 L GAS
View related parts
2005 Ford F-250 Super Duty Drive Shaft Part Number: 3C3Z-4602-AA
Product Specifications
- Other Name: Shaft Assembly - Drive; Driveshaft
- Base No.: 4602
- Item Weight: 36.10 Pounds
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 3C3Z-4602-AA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2005 Ford F-250 Super Duty Submodels:
- Harley-Davidson Edition, King Ranch, Lariat, XL, XLT | 8 Cyl 6.0 L DIESEL
View related parts
2005 Ford F-250 Super Duty Drive Shaft Part Number: 3C3Z-4R602-BPX
Product Specifications
- Other Name: Shaft Assembly - Drive; Driveshaft
- Replaces: 3C3Z-4R602-BP
- Base No.: 4R602
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 3C3Z-4R602-BPX
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2005 Ford F-250 Super Duty Submodels:
- Harley-Davidson Edition, King Ranch, Lariat, XL, XLT | 8 Cyl 6.0 L DIESEL
View related parts
2005 Ford F-250 Super Duty Drive Shaft Part Number: 3C3Z-4R602-CR
Product Specifications
- Other Name: Shaft Assembly - Drive; Driveshaft
- Base No.: 4R602
- Item Weight: 55.60 Pounds
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 3C3Z-4R602-CR
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2005 Ford F-250 Super Duty Submodels:
- Harley-Davidson Edition, King Ranch, Lariat, XL, XLT | 10 Cyl 6.8 L GAS

| Page 1 of 2 |Next >

1-20 of 39 Results

2005 Ford F-250 Super Duty Drive Shaft

If you're seeking quality and affordability, look no further than our extensive inventory of genuine 2005 Ford F-250 Super Duty Drive Shaft available at FordPartsDeal.com. You can confidently purchase our OEM 2005 Ford F-250 Super Duty Drive Shaft as they are supported by the manufacturer's warranty and our hassle-free return policy, alongside the benefit of our fast delivery service.

2005 Ford F-250 Super Duty Drive Shaft Parts Q&A

Q: How to Service and Repair the Rear One-Piece Drive Shaft for 4X2 on 2005 Ford F-250 Super Duty?
A: Begin front driveshaft service and repair of 4x2 vehicles by hoisting the vehicle so its transmission is set to neutral. Rephrase the driveshaft to the transmission extension housing by making index marks for vehicles that use slip yokes to prevent output shaft rotation. The circular flange service requires marking both the driveshaft yoke and the transmission flange but split pin yoke vehicles need index-marking of the driveshaft and rear axle pinion flange. Use a wrench to remove and discard the four bolts and two u-joint retainers from split pin yoke vehicles and release four bolts only on circular flange vehicles with different bolt directions based on application requirements. Driveshaft separation should occur at the rear axle pinion flange position on automatic transmissions along with a removal of the manual transmission driveshaft or its sliding distance backward off the output shaft. Stick the bearing cups onto the spider and close the automatic transmission extension housing with a plug to stop fluid leakage. The slip-yoke spline of vehicles with slip yokes needs grease during installation and the extension housing plug removal should occur at the same time as slip-yoke transmission output shaft alignment for driveshaft installation. Circular flange vehicles require that the driveshaft yoke be placed on the transmission flange where index marks should align and new bolts should be installed with care for their directions. When working on split pin flange vehicles personnel must first remove tape from bearing cups before they line up the index marks while placing these cups into the rear axle pinion flange. You should install loose four bolts on the circular flange yoke for the driveshaft at the rear axle pinion flange and follow a cross pattern to achieve proper seating. The process for split pin yoke vehicles requires installation of two new retainers followed by four new bolts before lowering the vehicle.