How to service the rear bumper cover on 2005 Ford Freestar?

Service of the rear bumper cover starts with the removal of four rear bumper screws along with three push pins and five additional rear bumper screws before the rear bumper cover can be detached. Users must detach the parking aid wiring harness electrical connector along with removing parking aid sensors when installing a new bumper cover. Secure the new bumper cover on a scratch-free clean surface for installation because it protects against possible damage to the cover. From inside the bumper cover drill a 3.18 mm (0.12 in) pilot hole which should not exceed its shape to guarantee parking aid sensor alignment. To achieve proper sensor positioning you must drill with the drill perpendicular to the surface by using a 28.58 mm (1.12 in) hole saw beginning from the exterior side. Drill the holes and do not cross scribe lines except for Sport vehicles where both inboard holes require trimming according to the scribe line configuration. Sport vehicle owners need to trim both holes found inside and outside the bumper. Perform keyway notching from the inner side while removing burrs that appear on the holes. The outer bracket should be flush with the bumper cover while exactly following its contours and requiring hole bottom filing for proper fit. Place the outer bracket homing its locating ribs into the keyways of the system while making certain neither the sensors nor brackets will turn during installation. Place the locating lug of the parking aid sensor into the notch on the bracket for installation of rear parking aid sensors followed by connection of the parking aid wiring harness and electrical connectors. The procedures for bumper installation include connecting the wiring harness electrical connector for the parking aid system if present then securing the new or original bumper cover through 5 rear screws and 3 push pins and finally securing it with the remaining 4 screws.

OEM 2005 Ford Freestar Bumper

Bumper Fascia

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

10 Bumpers found

View related parts
2005 Ford Freestar Bumper Cover, Front
Part Number: 3F2Z-17D957-RAA
$366.05 MSRP: $506.40
You Save: $140.35 (28%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Cover; Bumper Cover, Front
- Position: Front
- Base No.: 17D957
- Item Weight: 32.60 Pounds
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 3F2Z-17D957-RAA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2005 Ford Freestar Submodels:
- S, SE | 6 Cyl 3.9 L GAS, 6 Cyl 4.2 L GAS
View related parts
2005 Ford Freestar Impact Bar, Front
Part Number: 3F2Z-17757-AA
$104.39 MSRP: $142.06
You Save: $37.67 (27%)
ADD TO CART
Product Specifications
- Other Name: Bumper Assembly - Front; Bumper Impact Bar, Front
- Position: Front
- Replaces: XF2Z-17757-AA
- Base No.: 17757
- Item Weight: 15.40 Pounds
- Item Dimensions: 8.2 x 6.1 x 54.6 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 3F2Z-17757-AA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2005 Ford Freestar Submodels:
- Base, Limited, S, SE, SEL, SES | 6 Cyl 3.9 L GAS, 6 Cyl 4.2 L GAS
View related parts
2005 Ford Freestar Bumper Cover, Rear
Part Number: 3F2Z-17K835-RAA
$361.43 MSRP: $495.88
You Save: $134.45 (28%)
ADD TO CART
Product Specifications
- Other Name: Cover; Bumper Cover, Rear
- Position: Rear
- Base No.: 17K835
- Item Weight: 12.80 Pounds
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 3F2Z-17K835-RAA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2005 Ford Freestar Submodels:
- SES | 6 Cyl 3.9 L GAS
View related parts
2005 Ford Freestar Impact Bar, Rear
Part Number: 3F2Z-17906-AA
$129.09 MSRP: $178.59
You Save: $49.50 (28%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bumper; Bumper Impact Bar, Rear
- Position: Rear
- Replaces: 3F2Z-17906-BA
- Base No.: 17906
- Item Weight: 13.50 Pounds
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 3F2Z-17906-AA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2005 Ford Freestar Submodels:
- Base, Limited, S, SE, SEL, SES | 6 Cyl 3.9 L GAS, 6 Cyl 4.2 L GAS
View related parts
2005 Ford Freestar Bumper Cover, Rear
Part Number: 3F2Z-17K835-SAA
Product Specifications
- Other Name: Cover; Bumper Cover, Rear
- Position: Rear
- Base No.: 17K835
- Item Weight: 12.90 Pounds
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 3F2Z-17K835-SAA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2005 Ford Freestar Submodels:
- Base, S, SE | 6 Cyl 3.9 L GAS, 6 Cyl 4.2 L GAS
View related parts
2005 Ford Freestar Bumper Cover, Rear
Part Number: 3F2Z-17K835-PAA
Product Specifications
- Other Name: Cover; Bumper Cover, Rear
- Position: Rear
- Base No.: 17K835
- Item Weight: 11.90 Pounds
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 3F2Z-17K835-PAA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2005 Ford Freestar Submodels:
- Limited, SEL | 6 Cyl 4.2 L GAS
View related parts
2005 Ford Freestar Bumper Cover, Rear
Part Number: 3F2Z-17K835-MAA
Product Specifications
- Other Name: Cover; Bumper Cover, Rear
- Position: Rear
- Base No.: 17K835
- Item Weight: 12.60 Pounds
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 3F2Z-17K835-MAA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2005 Ford Freestar Submodels:
- Base, S | 6 Cyl 3.9 L GAS
View related parts
2005 Ford Freestar Bumper Cover, Front
Part Number: 3F2Z-17D957-SAA
Product Specifications
- Other Name: Cover; Bumper Cover, Front
- Position: Front
- Base No.: 17D957
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 3F2Z-17D957-SAA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2005 Ford Freestar Submodels:
- Base | 6 Cyl 3.9 L GAS
View related parts
2005 Ford Freestar Bumper Cover, Front
Part Number: 3F2Z-17D957-NAA
Product Specifications
- Other Name: Cover; Bumper Cover, Front
- Position: Front
- Base No.: 17D957
- Item Weight: 112.40 Pounds
- Item Dimensions: 87.4 x 45.5 x 33.7 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 3F2Z-17D957-NAA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2005 Ford Freestar Submodels:
- Limited, SEL | 6 Cyl 4.2 L GAS
View related parts
2005 Ford Freestar Bumper Cover, Front
Part Number: 3F2Z-17D957-MAA
Product Specifications
- Other Name: Cover; Bumper Cover, Front
- Position: Front
- Base No.: 17D957
- Item Weight: 34.60 Pounds
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 3F2Z-17D957-MAA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2005 Ford Freestar Submodels:
- SES | 6 Cyl 3.9 L GAS

2005 Ford Freestar Bumper

If you're seeking quality and affordability, look no further than our extensive inventory of genuine 2005 Ford Freestar Bumper available at FordPartsDeal.com. You can confidently purchase our OEM 2005 Ford Freestar Bumper as they are supported by the manufacturer's warranty and our hassle-free return policy, alongside the benefit of our fast delivery service.

2005 Ford Freestar Bumper Parts Questions & Experts Answers

Q: How to service the rear bumper cover on 2005 Ford Freestar?
A: Service of the rear bumper cover starts with the removal of four rear bumper screws along with three push pins and five additional rear bumper screws before the rear bumper cover can be detached. Users must detach the parking aid wiring harness electrical connector along with removing parking aid sensors when installing a new bumper cover. Secure the new bumper cover on a scratch-free clean surface for installation because it protects against possible damage to the cover. From inside the bumper cover drill a 3.18 mm (0.12 in) pilot hole which should not exceed its shape to guarantee parking aid sensor alignment. To achieve proper sensor positioning you must drill with the drill perpendicular to the surface by using a 28.58 mm (1.12 in) hole saw beginning from the exterior side. Drill the holes and do not cross scribe lines except for Sport vehicles where both inboard holes require trimming according to the scribe line configuration. Sport vehicle owners need to trim both holes found inside and outside the bumper. Perform keyway notching from the inner side while removing burrs that appear on the holes. The outer bracket should be flush with the bumper cover while exactly following its contours and requiring hole bottom filing for proper fit. Place the outer bracket homing its locating ribs into the keyways of the system while making certain neither the sensors nor brackets will turn during installation. Place the locating lug of the parking aid sensor into the notch on the bracket for installation of rear parking aid sensors followed by connection of the parking aid wiring harness and electrical connectors. The procedures for bumper installation include connecting the wiring harness electrical connector for the parking aid system if present then securing the new or original bumper cover through 5 rear screws and 3 push pins and finally securing it with the remaining 4 screws.