How to Remove and Replace the Rear Three-Piece Drive Shaft on 2007 Ford F-350 Super Duty?

The first step to handle a three-piece rear driveshaft replacement must start by positioning the vehicle on a hoist while it remains in neutral gear. Mark the driveshaft location on the axle flange and proceed to separate it from the flange by removing its bolts along with U-joint retainers before supporting the driveshaft with mechanic's wire. Secondly detach the driveshaft from its coupling shaft position by taking out the bolts and U-joint retainers then supporting the driveshaft. The center bearing support bolts and rear driveshaft assembly must be removed while preserving the driveshaft position with its transmission flange or output shaft. A circular-flanged driveshaft requires users to first discard the transmission-to-driveshaft bolts before proceeding to remove the center bearing support bolts then front driveshaft pieces. The slip yoke needs driveshaft relocation by lowering it away from the transmission output shaft before carefully plugging the extension housing to avoid fluid leakage. Clean all components including driveshaft yoke areas as well as center bearing bearing and rubber insulator by wiping them dry without solvent immersion. Check for damage in the universal joint slip yoke boot while inspecting the driveshaft center bearing support for rough action and evaluate the center bearing rubber insulator for signs of deterioration as well as cracks or hardening before replacing defective parts. Connect the front driveshaft to the transmission while ensuring index mark alignment by using new bolts which should be hand-tightened. Vehicle owners must line up their index marks when inserting the slip yoke of the driveshaft onto the output shaft. Center support bearing placement should be followed by bolt installation while leaving them hand-tightened. Use a torque wrench to tighten all driveshaft-to-transmission flange bolts as well as all driveshaft center bearing bolts to 102 Nm (75 ft. lbs.). After placing the rear driveshaft assembly in position the technician should install the center support bearing bolts while maintaining light tension. The procedures involve joining the rear driveshaft to the front driveshaft through new retainers and driveshaft-to-coupling shaft bolts with final torque set to 35 Nm (26 ft. lbs.). The same torque follows for connecting the rear driveshaft assembly to the rear axle through new retainers and driveshaft-to-axle bolts. Tighten the driveshaft center support bearing bolts with a torque of 63 Nm which equals 46 ft. lbs.

OEM 2007 Ford F-350 Super Duty Drive Shaft

Axle Shaft

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

35 Drive Shafts found

View related parts
2007 Ford F-350 Super Duty Drive Shaft Part Number: 6C3Z-4602-B
$364.13 MSRP: $503.73
You Save: $139.60 (28%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Shaft Assembly - Drive; Driveshaft
- Replaces: 5C3Z-4602-VB
- Base No.: 4602
- Item Weight: 31.50 Pounds
- Item Dimensions: 25.7 x 6.1 x 15.2 inches
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 6C3Z-4602-B
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2007 Ford F-350 Super Duty Submodels:
- King Ranch, Lariat, XL, XLT | 8 Cyl 5.4 L GAS
View related parts
2007 Ford F-350 Super Duty Drive Shaft Part Number: 2C3Z-4602-AA
Product Specifications
- Other Name: Shaft Assembly - Drive; Driveshaft
- Base No.: 4602
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 2C3Z-4602-AA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following 2007 Ford F-350 Super Duty Submodels:
- Harley-Davidson Edition, King Ranch, Lariat, XL, XLT | 10 Cyl 6.8 L GAS
View related parts
2007 Ford F-350 Super Duty Drive Shaft Part Number: 2C3Z-4602-AD
Product Specifications
- Other Name: Shaft Assembly - Drive; Driveshaft
- Base No.: 4602
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 2C3Z-4602-AD
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following 2007 Ford F-350 Super Duty Submodels:
- King Ranch, Lariat, XL, XLT | 8 Cyl 5.4 L GAS
View related parts
2007 Ford F-350 Super Duty Drive Shaft Part Number: 2C3Z-4602-DA
Product Specifications
- Other Name: Shaft Assembly - Drive; Driveshaft
- Base No.: 4602
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 2C3Z-4602-DA
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following 2007 Ford F-350 Super Duty Submodels:
- King Ranch, Lariat, XL, XLT | 8 Cyl 5.4 L GAS
View related parts
2007 Ford F-350 Super Duty Drive Shaft Part Number: 2C3Z-4602-EB
Product Specifications
- Other Name: Shaft Assembly - Drive; Driveshaft
- Replaces: 2C3Z-4602-EA
- Base No.: 4602
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 2C3Z-4602-EB
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2007 Ford F-350 Super Duty Submodels:
- Harley-Davidson Edition, King Ranch, Lariat, XL, XLT | 10 Cyl 6.8 L GAS, 8 Cyl 5.4 L GAS
View related parts
2007 Ford F-350 Super Duty Drive Shaft Part Number: 2C3Z-4602-NB
Product Specifications
- Other Name: Shaft Assembly - Drive; Driveshaft
- Replaces: 2C3Z-4602-NA, 2C3Z-4602-XA
- Base No.: 4602
- Item Weight: 41.90 Pounds
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 2C3Z-4602-NB
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2007 Ford F-350 Super Duty Submodels:
- Harley-Davidson Edition, King Ranch, Lariat, XL, XLT | 10 Cyl 6.8 L GAS, 8 Cyl 5.4 L GAS
View related parts
2007 Ford F-350 Super Duty Drive Shaft Part Number: 2C3Z-4R602-AXX
Product Specifications
- Other Name: Shaft Assembly - Drive; Driveshaft
- Base No.: 4R602
- Item Weight: 58.90 Pounds
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 2C3Z-4R602-AXX
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2007 Ford F-350 Super Duty Submodels:
- King Ranch, Lariat, XL, XLT | 8 Cyl 5.4 L GAS
View related parts
2007 Ford F-350 Super Duty Drive Shaft Part Number: 2C3Z-4R602-BZ
Product Specifications
- Other Name: Shaft Assembly - Drive; Driveshaft
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 2C3Z-4R602-BZ
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following 2007 Ford F-350 Super Duty Submodels:
- Harley-Davidson Edition, King Ranch, Lariat, XL, XLT | 10 Cyl 6.8 L GAS
View related parts
2007 Ford F-350 Super Duty Drive Shaft Part Number: 2C3Z-4R602-CPC
Product Specifications
- Other Name: Shaft Assembly - Drive; Driveshaft
- Replaces: 2C3Z-4R602-CP, 2C3Z-4R602-CPB
- Item Weight: 73.40 Pounds
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 2C3Z-4R602-CPC
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2007 Ford F-350 Super Duty Submodels:
- King Ranch, Lariat, XL, XLT | 8 Cyl 5.4 L GAS
View related parts
2007 Ford F-350 Super Duty Drive Shaft Part Number: 2C3Z-4R602-DPX
Product Specifications
- Other Name: Shaft Assembly - Drive; Driveshaft
- Replaces: 2C3Z-4R602-DP
- Base No.: 4R602
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 2C3Z-4R602-DPX
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2007 Ford F-350 Super Duty Submodels:
- Harley-Davidson Edition, King Ranch, Lariat, XL, XLT | 8 Cyl 6.0 L DIESEL
View related parts
2007 Ford F-350 Super Duty Drive Shaft Part Number: 2C3Z-4R602-DQX
Product Specifications
- Other Name: Shaft Assembly - Drive; Driveshaft
- Replaces: 2C3Z-4R602-DQ
- Base No.: 4R602
- Item Weight: 54.80 Pounds
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 2C3Z-4R602-DQX
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2007 Ford F-350 Super Duty Submodels:
- Harley-Davidson Edition, King Ranch, Lariat, XL, XLT | 10 Cyl 6.8 L GAS, 8 Cyl 5.4 L GAS
View related parts
2007 Ford F-350 Super Duty Drive Shaft Part Number: 2C3Z-4R602-DSX
Product Specifications
- Other Name: Shaft Assembly - Drive; Driveshaft
- Base No.: 4R602
- Item Weight: 60.50 Pounds
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 2C3Z-4R602-DSX
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2007 Ford F-350 Super Duty Submodels:
- King Ranch, Lariat, XL, XLT | 8 Cyl 5.4 L GAS
View related parts
2007 Ford F-350 Super Duty Drive Shaft Part Number: 2C3Z-4R602-DUX
Product Specifications
- Other Name: Shaft Assembly - Drive; Driveshaft
- Base No.: 4R602
- Item Weight: 57.20 Pounds
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 2C3Z-4R602-DUX
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2007 Ford F-350 Super Duty Submodels:
- Harley-Davidson Edition, King Ranch, Lariat, XL, XLT | 10 Cyl 6.8 L GAS, 8 Cyl 6.0 L DIESEL
View related parts
2007 Ford F-350 Super Duty Drive Shaft Part Number: 2C3Z-4R602-ED
Product Specifications
- Other Name: Shaft Assembly - Drive; Driveshaft
- Item Weight: 60.00 Pounds
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 2C3Z-4R602-ED
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following 2007 Ford F-350 Super Duty Submodels:
- Harley-Davidson Edition, King Ranch, Lariat, XL, XLT | 10 Cyl 6.8 L GAS
View related parts
2007 Ford F-350 Super Duty Drive Shaft Part Number: 2C3Z-4R602-PC
Product Specifications
- Other Name: Shaft Assembly - Drive; Driveshaft
- Base No.: 4R602
- Item Weight: 68.30 Pounds
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 2C3Z-4R602-PC
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2007 Ford F-350 Super Duty Submodels:
- King Ranch, Lariat, XL, XLT | 8 Cyl 5.4 L GAS
View related parts
2007 Ford F-350 Super Duty Drive Shaft Part Number: 3C3Z-4602-AM
Product Specifications
- Other Name: Shaft Assembly - Drive; Driveshaft
- Base No.: 4602
- Item Weight: 36.40 Pounds
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 3C3Z-4602-AM
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2007 Ford F-350 Super Duty Submodels:
- Harley-Davidson Edition, King Ranch, Lariat, XL, XLT | 8 Cyl 6.0 L DIESEL
View related parts
2007 Ford F-350 Super Duty Drive Shaft Part Number: 3C3Z-4602-AR
Product Specifications
- Other Name: Shaft Assembly - Drive; Driveshaft
- Replaces: 3C3Z-4602-AH
- Base No.: 4602
- Item Weight: 32.40 Pounds
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 3C3Z-4602-AR
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2007 Ford F-350 Super Duty Submodels:
- King Ranch, Lariat, XL, XLT | 8 Cyl 5.4 L GAS
View related parts
2007 Ford F-350 Super Duty Drive Shaft Part Number: 3C3Z-4602-BB
Product Specifications
- Other Name: Shaft Assembly - Drive; Driveshaft
- Replaces: 3C3Z-4602-BA
- Base No.: 4602
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 3C3Z-4602-BB
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2007 Ford F-350 Super Duty Submodels:
- Harley-Davidson Edition, King Ranch, Lariat, XL, XLT | 8 Cyl 5.4 L GAS, 8 Cyl 6.0 L DIESEL
View related parts
2007 Ford F-350 Super Duty Drive Shaft Part Number: 3C3Z-4R602-BPX
Product Specifications
- Other Name: Shaft Assembly - Drive; Driveshaft
- Replaces: 3C3Z-4R602-BP
- Base No.: 4R602
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 3C3Z-4R602-BPX
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
More Info
Fits the following 2007 Ford F-350 Super Duty Submodels:
- Harley-Davidson Edition, King Ranch, Lariat, XL, XLT | 8 Cyl 6.0 L DIESEL
View related parts
2007 Ford F-350 Super Duty Drive Shaft Part Number: 3C3Z-4R602-BZ
Product Specifications
- Other Name: Shaft Assembly - Drive; Driveshaft
- Base No.: 4R602
- Condition: New
- Fitment Type: Direct Replacement
- SKU: 3C3Z-4R602-BZ
- Warranty: This genuine part is guaranteed by Ford's factory warranty.
Fits the following 2007 Ford F-350 Super Duty Submodels:
- Harley-Davidson Edition, King Ranch, Lariat, XL, XLT | 8 Cyl 6.0 L DIESEL

| Page 1 of 2 |Next >

1-20 of 35 Results

2007 Ford F-350 Super Duty Drive Shaft

If you're seeking quality and affordability, look no further than our extensive inventory of genuine 2007 Ford F-350 Super Duty Drive Shaft available at FordPartsDeal.com. You can confidently purchase our OEM 2007 Ford F-350 Super Duty Drive Shaft as they are supported by the manufacturer's warranty and our hassle-free return policy, alongside the benefit of our fast delivery service.

2007 Ford F-350 Super Duty Drive Shaft Parts Q&A

Q: How to Remove and Replace the Rear Three-Piece Drive Shaft on 2007 Ford F-350 Super Duty?
A: The first step to handle a three-piece rear driveshaft replacement must start by positioning the vehicle on a hoist while it remains in neutral gear. Mark the driveshaft location on the axle flange and proceed to separate it from the flange by removing its bolts along with U-joint retainers before supporting the driveshaft with mechanic's wire. Secondly detach the driveshaft from its coupling shaft position by taking out the bolts and U-joint retainers then supporting the driveshaft. The center bearing support bolts and rear driveshaft assembly must be removed while preserving the driveshaft position with its transmission flange or output shaft. A circular-flanged driveshaft requires users to first discard the transmission-to-driveshaft bolts before proceeding to remove the center bearing support bolts then front driveshaft pieces. The slip yoke needs driveshaft relocation by lowering it away from the transmission output shaft before carefully plugging the extension housing to avoid fluid leakage. Clean all components including driveshaft yoke areas as well as center bearing bearing and rubber insulator by wiping them dry without solvent immersion. Check for damage in the universal joint slip yoke boot while inspecting the driveshaft center bearing support for rough action and evaluate the center bearing rubber insulator for signs of deterioration as well as cracks or hardening before replacing defective parts. Connect the front driveshaft to the transmission while ensuring index mark alignment by using new bolts which should be hand-tightened. Vehicle owners must line up their index marks when inserting the slip yoke of the driveshaft onto the output shaft. Center support bearing placement should be followed by bolt installation while leaving them hand-tightened. Use a torque wrench to tighten all driveshaft-to-transmission flange bolts as well as all driveshaft center bearing bolts to 102 Nm (75 ft. lbs.). After placing the rear driveshaft assembly in position the technician should install the center support bearing bolts while maintaining light tension. The procedures involve joining the rear driveshaft to the front driveshaft through new retainers and driveshaft-to-coupling shaft bolts with final torque set to 35 Nm (26 ft. lbs.). The same torque follows for connecting the rear driveshaft assembly to the rear axle through new retainers and driveshaft-to-axle bolts. Tighten the driveshaft center support bearing bolts with a torque of 63 Nm which equals 46 ft. lbs.